Question about 2003 Hyundai Tiburon

1 Answer

The flasher unit (turn signal and hazard) starts the clicking sound as soon as the ignition key is turned on.

All lights work correctly when I activate the turn signal or turn on my hazards. The flasher unit however continuously clicks as if they signals are on, but they are not.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 1,615 Answers

Sounds to me the switch is bad, as if its stuck in the turn signal position, could be the relay or blinker faulty. Replace the blinker/relay and if thats all good, its your turn signal switch.

Posted on Dec 16, 2013

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
ghost45

PAUL MC G

  • 1280 Answers

SOURCE: The Flashers all work Hazard and l & R signals or they all do not

Go to www.hmaservice.com and register( Vehicle by VIN). Afterward, you have access to shop manuals, service bulletins, wiring diagrams, etc. about your vehicle.Take/Tow your vehicle to an authorized Hyundai dealership and pay the diagnostic fee... they will tell you exactly what the problem is and the cost of parts/labor to fix it... at least this way you'll know what the problem is and what's required to fix it.

Posted on Oct 04, 2009

Rajkumar S

  • 104 Answers

SOURCE: turn signals and hazard lights won't work. already

Check the Fuse box loacted inside the hood. Look for the guidance on the top of the fuse box for locating trun signal fuses.

Check whether they are good. If not replace with correct rating fuse. If the problem is not solved still, wiring harness has to be checked as the bulbs & flashers are replaced already.

Posted on Jun 05, 2010

rickyrt441

Richard Hale

  • 4399 Answers

SOURCE: i have an unusual fault. My indicators/hazards do

It could be the switch itself or the flasher unit.

Posted on Feb 17, 2011

customcan

Johny Oz

  • 113 Answers

SOURCE: turn signals working, but not

i beileve there is a seprit flasher for hazard take to look at that or check hazard switch its maybe the problem.

Posted on Jul 17, 2011

terry rudolph

  • 112 Answers

SOURCE: turn signal dosen't work but hazard does

there are actually two flashers in your car one for the hazards one for the turn signals... try replacing the flasher for the turn signals.

Posted on Jul 14, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the emergency flasher relay located on 2013 Rogue?


Here is what the service manual says. Looks like it is not a flasher relay but a function of the body control module.

TURN SIGNAL AND HAZARD WARNING LAMP SYSTEMSystem Description OUTLINE Turn signal lamp and the hazard warning lamp is controlled by combination switch reading function and the flasher control function of BCM.
TURN SIGNAL LAMP OPERATION - BCM detects the combination switch condition by the combination switch reading function. - BCM supplies voltage to the right (left) turn signal lamp circuit when the ignition switch is turned ON and the turn signal switch is in the right (left) position. BCM blinks the turn signal lamp.
HAZARD WARNING LAMP OPERATION BCM supplies voltage to both turn signal lamp circuit when the hazard switch is turned ON. BCM blinks the hazard warning lamp.
TURN SIGNAL INDICATOR LAMP AND TURN SIGNAL SOUND OPERATION - BCM transmits the turn indicator signal to the combination meter with CAN communication while the turn signal lamp and the hazard warning lamp are operating. - Combination meter outputs the turn signal sound with the integrated buzzer while blinking the turn signal indicator lamp according to the turn indicator signal.
HIGH FLASHER OPERATION (FAIL-SAFE) - BCM detects the turn signal lamp circuit status by the terminal current value. - BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal lamp operating. NOTE: The blinking speed is normal while operating the hazard warning lamp.

Oct 13, 2014 | 2013 Nissan Rogue

1 Answer

I have a 2002 Pontiac Firebird. Hazard lights work. Turn signals were working without clicking sound, now not working. A local parts shop said the problem is the turn signal flasher unit. Where do I locate...


There are two seperate flashers, one for the hazards, and one for the turn signals. They are located behind the lower instrument panel below the steering wheel. Turn flasher should be the one on the right. These are also notorious for the front light sockets to corode or burn out. check their condition and be sure to use connector lube when replacing bulbs there.

Sep 03, 2011 | 2002 Pontiac Firebird

2 Answers

My hazards work. My blinkers do not work at all. No sound or light.


there is a separeate flasher relay for turn signals,usullay by hazzard flashers.turn on hazzards use sound to locate,turn flasher will be near.some will interchange to get you by till you can replace.

Feb 17, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Where do replace the flasher. is it under the hood?


Hi!!
Check under dash, usually to the left of the steering column. Turn Ignition Key to the ON position (engine OFF) and the Turn Signal lever to either side, follow the clicking sound, if Turn Signal Flasher is completely out, activate the hazard lights, if they work, follow that click, usually both flashers are together.
Good Luck! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.

Feb 11, 2011 | 1992 Plymouth Acclaim

3 Answers

Turn signals wont work fuses are good?


the hazard switch above the radio is your problem. if you put on your signals and they don't flash turn hazards on then off and they will flash. (changing this *** will fix your problem

Aug 30, 2009 | 1999 Pontiac Grand Am GT

1 Answer

Haz flashers wont work but blinkers do


There are 2 seperate flashers 1 for turn signals and 1 for hazard.The hazard flasher is located in the convenance center the turn flasher in the fuse box. Also seperate fuse's for each. One battery circuit for hazard Ignition for turn signals.Check fuse for hazard,if good try swapping in the turn signal flasher and see if hazards work.They use the same flasher unit.

Aug 20, 2009 | 1993 GMC Safari

2 Answers

My hazard lights work but the turn signals wont


Have you tried changing the flasher unit (the small plugin unit that makes the click sound when flashing)?

These units come in several variations - perhaps an unsuitable unit has been installed.

If none of the above suggestions help, you should re-check the operation on the turn signal switch.
In one of the turn positions, if you bridge out the 2 correct pins of the flasher unit, the indicators on one side should light when you move the switch to that position.
Move the switch to the other turn position, and the indicator lights on that side should light.

If none of the above helps, you will need a vehicle wiring diagram to help find the problem.


Jun 11, 2009 | 1994 Chevrolet Cavalier

1 Answer

Renault laguna 1.9tdi dynamique 51 reg. hazard warning lights do not work, changed fuse still not working. whats wrong with them


If your turn signals work, then replace the flasher for your hazards. Turn your key on then give a left turn signal. Listen for the "clicking" sound near your brake pedal and accelerator. Once you locate your turn signal flasher (small, "cylinderical", device) the hazard flasher should be near it. Simply pull out the flasher and replace... just plugs in.

Jun 07, 2009 | 2000 Renault 181

2 Answers

Hazard Lights Won't Work on 96 Taurus


FIRST Check for Blown Fuse Then Locate Flasher Units @ Fuse Block to Determine Wiitch one is Hazard Turn On Key Then Turn Syg. Feel Flashers The One you feel Clicking is For Turn The Other IS Flasher Replace this Flasher unit.

  1. Verify the customer's concern by operating the turn signal/hazard flasher lamp to duplicate the condition.
  2. Inspect to determine if one of the electrical concerns apply: VISUAL INSPECTION CHART Electrical
    • Circuitry open/shorted.
    • Fuse junction panel Fuse:
+ 15 (10 A) + 29 (15 A)
  • Damaged multi-function switch.
  • Miniature bulb burned out.
  • Damaged lamp.
  1. If the inspection reveals obvious concern(s) that can be readily identified, service as required.
  2. If the concern(s) remains after the inspection, determine the symptom(s) and go to the Symptom Chart. See: ProceduresSymptom Chart(s)

Jun 01, 2009 | 1996 Ford Taurus

2 Answers

Turn signals and emergency flashers stopped


they are under the dash, but its highly unlikly that both would go bad at the same timeyour promlem is probly in the steering colum

Mar 05, 2009 | 1997 Mercury Sable

Not finding what you are looking for?
2003 Hyundai Tiburon Logo

311 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...