Question about 1996 Honda Accord

1 Answer

ABS Light On

When I turb the engine on after about 15-20 seconds I hear a click in the abs unit behind the passenger side kickplate and then my abs light comes on. I DONT hear the pump try to pressure up, I hear nothing. If the pump was bad would I hear it trying to pressure up? I think it might be a wheel sensor and will try to determine that with the abs light code it reveals. What do you think?

Posted by on

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Honda Master
  • 22,486 Answers

Wont hear pump check and test the sensors --have scanned for a trouble code which can narrow down a problem --also check and test hubs / wheel bearings

Posted on May 28, 2018

Ad

4 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 740 Answers

SOURCE: 1996 Honda Odyssey strange, intermittent ABS problem

If you are absolutely sure that the all the abs sensors are good. Then the only other factors are the abs unit itself and the abs computer. Please have the system checked with a a scanner to make sure. Remember the only way to an ABS light will reset is by driving the vehicle and if every component of the system is fine the light will go out. Because your light is on there is a problem in the system and your abs is not functioning when the light is ON .Good Luck

Posted on Dec 09, 2008

Anonymous

  • 1 Answer

SOURCE: ABS pump failure

Hi,
The problem is the solonoids inside the modulator are stuck, all you need to do is!!! Clear the code, than drive car while no abs light is on than lock the car a few times on wet road. The will help to free up the solonoids. Do this about 10 times, brake fluid is the only parts needed!!! Call me at 302 529 7888 if you like!!!
Dave

Posted on Feb 07, 2009

yup it broke

  • 105 Answers

SOURCE: Honda Civic 2007 Civic . Cahange wheel bearing and

sorry to tell you this but it sounds like the wheel bearing was put in backwards on one or both sides. the front wheel bearings have a black speed ring built in and that is what your speed sensor reads off. - this is common as the front bearings will install either way- hope this helps

Posted on Dec 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Traxtion and ABS lights come on at same time and noise come from front area of car. What does this mean?


Depending on what car you have. It's as though you have an abs ring/sensor fault, the noise you are hearing is the abs pump working this is because the gap between the abs sensor and the abs ring is to close, which make's the abs control module think that the wheel has locked up. causing it to open the valves in the abs hydro unit to try take away the pressure from the side with the fault.

Oct 18, 2016 | Cars & Trucks

1 Answer

2001 Dodge Ram 1500 4x4 with no heat, no ac, blows room temp air on all fan settings


The upper passenger side firewall has a little black line passing through it . Usually it is broken. There is also a ball on the drivers side firewall behind the hinge

Nov 03, 2012 | 2001 Dodge Ram 2500 Truck

1 Answer

D4 light stays on and car does not change gears; speedometer ok


Had the same problem with my 92 accord LX, almost drove me Crazy. The car seemed to be taking off in second or third gear, and not shifting at all. Then it would work perfectly for a while, but kept getting worse and finally the problem was constant. I checked all the shifter relays on the transmission, took them apart and cleaned them, checked for power, all was well. My problem was the Transmission Control Unit. ( TCU ) It is located under the Passenger side carpet. Remove the carpet, then unbolt the kickplate. The TCU is bolted to the underside of the kickplate. So is the ECU (engine control unit) they are marked. My problem was Ants, they had made a nest there. I unbolted the TCU from the kickplate, unplugged it and removed the top cover of the unit, (4 screws on the sides). I sprayed the hell out of it with WD-40. I also plugged and unplugged the connector many times to assure connectivity. Been working like a dream for 3 years. Your problem may be a bad TCU. You should test it before reassembly. Just plug it in, and jump it to ground. The D4-3... and reverse lights should be lighting up. Disconnect the Battery before starting repair. Goodluck.
MoondogDan

Jul 10, 2009 | 1992 Honda Accord

1 Answer

Fuel pump reset button


The two most common places are in the trunk behind the fabric on either the left or right side. The second location is near the passenger side kickplate under the dashboard. You may have to remove the panel to access the button.

Apr 23, 2009 | 1996 Toyota Camry

1 Answer

1994 Audi 80 2.0 ABS Light Comes On then Engine Cuts Off


abs fault if you feel it though the pedal its activating, it should not activated, you will probably need to replace the abs unit as it would be the valve in the pump. engine cuts out as its found a fault.

Jun 07, 2017 | 1992 Audi 80

1 Answer

1996 Honda Odyssey strange, intermittent ABS problem


If you are absolutely sure that the all the abs sensors are good. Then the only other factors are the abs unit itself and the abs computer. Please have the system checked with a a scanner to make sure. Remember the only way to an ABS light will reset is by driving the vehicle and if every component of the system is fine the light will go out. Because your light is on there is a problem in the system and your abs is not functioning when the light is ON .Good Luck

Dec 09, 2008 | 1996 Honda Odyssey

2 Answers

E280 1994: ABS lights comes on, Engine stall during driving


Clean your ABS sensors thatg is mounted on the front disc rotors - they are usually covered with metal fillings and dust due to the magnetic properties of the sensors and also check or replace overload relay located behind battery - "Oldmerc" Australia

Oct 28, 2008 | 1990 Mercedes-Benz E-Class

1 Answer

Clicking noise in intrepid


Check on what relays are under there.

Oct 20, 2008 | 1997 Dodge Intrepid

2 Answers

1985 grand prix


the oil sending unit is located on the front of the engine(this is facing the passenger side fender.) to access it take the front tire off on passenger side you will see the oil filter and a sending unit right behind and above it it will have a green colored plug. please rate this. thanks

Sep 23, 2008 | 2002 Pontiac Grand Prix

Not finding what you are looking for?
1996 Honda Accord Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...