Question about BMW X3 Series

1 Answer

Bmw headlights both out

Both out simultaneously

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • BMW Master
  • 1,179 Answers

Check bulb + check fuse

Posted on Sep 18, 2016

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1999 Chrysler 300M. Simultaneously, the Check Engine light came on, the speedometer stopped working, and the car doesn't shift out of 2nd gear. What's the likely problem?


these vehicles have alot of problems with the tcm( tranmission control module) internal failures of trans speed sensors. your car is currently in "limp in mode" to protect your trasmission!!!

Sep 02, 2012 | 1999 Chrysler 300M

1 Answer

Trouble code p1300 for a 1998 toyota corolla


Hi there:
DTC 1300 - Igniter Circuit Malfunction (No.1)


A DIS (Direct Ignition System) has been adopted. The DIS improves the ignition timing accuracy, reduces high-voltage loss, and enhances the overall reliability of the ignition system by eliminating the distributor. The DIS is a 2-cylinder simultaneous ignition system which ignites 2 cylinders simultaneously with one ignition coil. In the 2-cylinder simultaneous ignition system, each of the 2 spark plugs is connected to the end of the secondary winding. High voltage generated in the secondary winding is applied directly to the 2 spark plugs. In one of the spark plugs, the spark passes from the center electrode to the ground electrode and in the other plug the discharge is in the opposite direction, i.e. from ground to center electrodes.

The ECM determines ignition timing and outputs the ignition signals (IGT) for each cylinder. Based on IGT signals, the igniter controls the primary ignition signals (IGC) for all ignition coils. At the same time, the igniter also sends an ignition confirmation signal (IGF) as a fail-safe measure to the ECM.


8_10_2012_8_12_47_pm.gif

Check diagnostics procedure in THIS LINK.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Aug 10, 2012 | 1998 Toyota Corolla

1 Answer

How do i program my lexus 2001 rx300 for a gate opener


You should see three buttons on the driver sun shade. Let's name them from left to right 1,2, and 3. Start by clearing any old codes. To clear codes press buttons 1 and 3 simultaneously until the light starts blinking. Release the buttons simultaneously. Before starting to program the car remotes you must have your gate hand held remote ready with a good charged battery. Now, to program your first gate car remote let's choose button 1. Press button 1 until it start blinking (about 20 seconds). Keeping button 1 pressed, activate your hand held remote close (about an inch) from the car button 1, until the light blinks faster than before. Release both remotes simultaneously. You are done programming your car remote button 1. For two additional gates remote controls programming repeat the procedure with button 2 and then with button 3.

Nov 13, 2010 | 2001 Lexus RX 300

1 Answer

How do i insert code for audi a6 2002 ? i have the code but i don-t now which button to press simultaneously.


IMPORTANT NOTE: You must have the security anti-theft code for your Audi radio from the car manufacturer, or from an Audi dealer!

The sequence of programming for Audi radio is:
1. Push simultaneous "SCAN" and "RDS" keys until on the screen will appear "1000" displayed.
2. Release keys. No more push on "SCAN" and "RDS" keys because otherwise number "1000" will be considered as first safe code attempt.
3. By the #1 key you will set up the first safe code digit.
4. By the #2 key you will set up the second safe code digit.
5. By the #3 key you will set up the third safe code digit.
6. By the #4 key you will set up the four-th safe code digit.
7. Then push again simultaneous "SCAN" and "RDS" keys for confirm this safe code. On the screen will be displayed "SAFE" notice. Release keys! For few seconds a radio frequence will be displayed. The radio is now ready for use!

Nov 11, 2010 | 2002 Audi A6

1 Answer

Windows open simultaneously and randomly, when car is shut off


The general module has failed. It is behind the glove box. The new module will have to be programmed. I would recommend taking it to the dealership. Allow them to diagnose it and repair it. Most likely if the problem happens again and it is raining outside, they would take responsibility for the water damage.

May 17, 2009 | 1999 BMW 323 Series

1 Answer

Battery Replacement now resets ??


Whenever battery power is disconnected, windows can "forget" their settings. Lower both windows simultaneously. Then raise them. When closed let go the window controls for one second then pull them up simultaneously again and hold for a count of three.

Thant should reset your windows.

Good luck.

Dec 06, 2008 | 2001 Audi TT

4 Answers

Program garage door opener


You must first erase what's in the memory.
1.) Simultaneously press both buttons 1 and 3 on the Audi's built-in remote. Hold them until the indicator light flashes (20 seconds or longer).
2.) Now hold your garage door remote close to the Audi remote.
3.) Simultaneously press and hold both your garage door remote button and the button you would like programmed. The indicator light will first flash slowly then rapidly.
4.) You may release both buttons once the light flashes rapidly.

Jul 01, 2008 | 2000 Audi A6

1 Answer

Problem light indicator


Thats indicating that a tail light is out not a back up light. You will need to check those rear lights closer.Your check engine light will need to be checked with a scanner for the codes and go from there.I don't think one has anything to do with the other. Hope this helps, Thanks ,Dan

Jun 21, 2008 | 1997 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

auntyjack

Level 2 Expert

104 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1176 Answers

Frankie B

Level 2 Expert

70 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...