Question about 1983 GMC S-15 Pickup

1 Answer

Remove the Center Support Drive Shaft Bearings

My son has a 1977 GMC Sierra 15. The center support drive shaft bearing holder broke. We bought a bearing assembly. How in the world do we get the bearing off the drive shaft??? Please help. Someone....please

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 71 Answers

Use a cutting wheel and cut through the bearing as far as you can without damaging the drive shaft.Then get a big hammer and a chisel drive the chisel into the cut and break the bearing.

Posted on Jun 25, 2009

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 4x4 sierra squeaks when i accelerate then goes away. only in drive


Check and see if your vehicle has a drive shaft center support. (carrier bearing). Make sure it is not dry that could be your problem or one of the front u-joints.

Mar 06, 2014 | 2002 GMC Sierra C/K1500

1 Answer

Two piece drive shaft vibrating


just take the drive shaft out and replace all u-joints (3) and ur center support bearing (1) in all on my 2002 gmc sierra 2wd it was 50 dollars

Dec 07, 2012 | 2007 GMC Sierra Classic

1 Answer

My 2005 GMC Sierra 1500 has a rear end roaring noise.


Change both axel bearings at the same time. The pinion bearing can be tested by slowly turning the drive shaft by hand and listening for any rough spots. It could be a carrier bearing or a bad U joint too. Isolate it by dropping the drive shaft and turning the pinion yoke by hand. If there is a problem, you'll be able it feel it. Then look at the drive shaft for worn carrier bearing and U joints.

Aug 16, 2017 | 2005 GMC Sierra

1 Answer

Vibration at above 85 km/h


DO U HAVE A 2 PIECE DRIVE SHAFT? IF SO REPLACE THE CENTER SUPPORT

May 28, 2010 | 2003 GMC Sierra 2500HD

1 Answer

Front dif bearing replacement


If it is the pilot shaft bearing then you will need to have a good impact wrench to remove the jamb nut. The ring gear assembly has to be removed,becareful not to lose the shims on both sides and keep them in order for each side. The inner bearing on the shaft is a pressed bearing so without proper tools these bearings are hard to remove.

Feb 04, 2010 | 2005 GMC Sierra

1 Answer

How to remove the ignition in 1991 GMC Sierra? My son broke off his key and the other half is stuck way down in the ignition.


disconnect neg battery terminal -remove steering wheel will need a puller some auto stores let u borrow these tools -remove turn signal switch not necessary to totally remove switch pull far enough rearward to slip over shaft but dont pull harness out of column --turn key to run -remove the lock retaining screws dont drop into column -remove lock -screw torque is 40 inch lbs for reg column 22 for adjustable column

Oct 21, 2009 | 1991 GMC Sierra

1 Answer

High speed Vibration comes and goes.


you need to take the shaft to a machine shop to have it pressed

Oct 01, 2009 | 1999 GMC Sierra

1 Answer

2001 gmc sierra 1500 2 wheel drive shakes when taking off from stop shakins stops at about 15 mph was told drive shaft angles to side then back to diff. is this normal mechanic said he was not sure if this...


on a two wheel drive the shaft should only angle down if this a used truck I would say the rear
axel was hit on the side that the drive shaft angels away from and the alignment should be checked out.

Mar 06, 2009 | 2001 GMC Sierra C/K3500

1 Answer

Replace Hanging bearing on drive shaft


I took a BIG hammer and wedge and beat the hell out of it until it released from the shaft.

Jan 25, 2009 | 2003 GMC Sierra 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,112 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...