Question about GMC Envoy

Open Question

Reaplace rear passenger blower resistor - Envoy GMC Cars & Trucks

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

tony batson

  • 56 Answers

SOURCE: 2003 grand caravan rear blower only works on high

check above the fuse panel

Posted on Feb 13, 2009

Ad
emissionwiz

Marvin

  • 85206 Answers

SOURCE: where is the rear blower motor resistor on 2001 Dogde Carvan?

no diagrams avil on fixya, sorry, the blower resistor is right next to the blower motor in the air duct that cools it.

Posted on Oct 19, 2009

Anonymous

  • 205 Answers

SOURCE: blower motor fan works on high setting only

The resistors are located in the firewall just above the blower motor. they have a heavier gadge wire going to it. As for the water if it is not antifreeze then you have a leak in your cowl area by the lower windshield. I ran in to this problem on several gm cars such as yours it can be deficult to find good luck

Posted on Oct 20, 2009

Testimonial: "Iccjester, thanks for the information it was very helpful much appreciation Mike S 1999 Buick Century"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010 tahoe heater works in rear only


Heater or blower. If it is the blower, then replace the blower resistor. Beside the blower under the dash on the passenger side. If it is the heat, then the system needs cleaned out or replace the heater core.

Jan 29, 2015 | 2010 Chevrolet Tahoe

1 Answer

Rear blower: only works on high when set on cold, won't work at all when set to heat


I would start with the rear blower motor resistor, the resistor is what controls the speed of the fan, the resistor is located in the rear heater box near the blower, you will need to remove the right rear side panel to access the heater box. start with that

Dec 07, 2012 | 2004 Honda Odyssey

1 Answer

Where is the blower resistor for front blower


The resistor pack is inside the vehicle (with rear AC), on the passenger side. If you are sitting in the passenger seat, your toes are pointing at it. There is a 5 wire harness hanging straight down plugged into it, and it is screwed into the ductwork using 2 8mm screws.

Also, could try this site: Durango_blower_resister.

Hope helps (remember to rate this answer).

Dec 15, 2010 | 2000 Dodge Durango

2 Answers

Wher is the blower resistor pack on a 2005 gmc pickup


Underneath the dash near the passengers feet, right next to the blower motor. It is held by two screws or is clipped in with plastic clips. Probably screws though and has a wire harness attached to it. Very easy to replace, just might have to lay on your back on the passenger side floor to visually see it and remove the resistor pack.

Oct 15, 2010 | 2005 GMC Sierra

1 Answer

Front heater will not blow air...heat trickles out... have smelled burning smell when put on high....rear heat works fine


It sounds like the blower motor has burned out. It probably ruined the blower motor resistor at the same time. I think the blower motor is right by the right (passenger side) hood hinge and the resistor is just under the motor.

Dec 14, 2009 | 2001 Ford Expedition

2 Answers

Front a/c blower motor not working,rear blower motor works fine on 2000 astro van, how do I fix it?


check the resistors located under the hood, passenger side in the air box. two screws hold it in place as well as a wire harness to un-plug. common problem on gm and chrysler.
If thats not broke and rusted, then check the motor, fuse, and the relay.

Sep 11, 2009 | 2000 Chevrolet Astro

2 Answers

Blower fan for 2000 lumina not working. how do i access blower resistor


Do u have high speed? if not it may be the blower motor and not the resistor, the blower motor and resistor (which is near it) are on the inside passenger side of car under the dash, u will have to lay on your back to even see it, and it is very hard to get at even then.

Dec 23, 2008 | Chevrolet Lumina Cars & Trucks

1 Answer

Durango vent blower fan


The blower motor resistors are known for going bad. Usually its because the blower starts drawing too much current. What I would recommend doing if you can and have the tools, is to check the blower motor connector to make sure 12 volts is present. If so than I would recommend replacing the blower motor resistor. Then if the same issue ever happens again and the blower motor resistor is bad again, you will need to replace the blower motor and the blower resistor as the final repair.
Here is some info about testing the resistor using a multimeter it you have one:

DIAGNOSIS AND TESTING- BLOWER MOTOR RESISTOR WARNING: ON VEHICLES EQUIPPED WITH AIRBAGS, DISABLE THE AIRBAG SYSTEM BEFORE ATTEMPTING ANY STEERING WHEEL, STEERING COLUMN, OR INSTRUMENT PANEL COMPONENT DIAGNOSIS OR SERVICE. DISCONNECT AND ISOLATE THE BATTERY NEGATIVE (GROUND) CABLE, THEN WAIT TWO MINUTES FOR THE AIRBAG SYSTEM CAPACITOR TO DISCHARGE BEFORE PERFORMING FURTHER DIAGNOSIS OR SERVICE. FAILURE TO TAKE THE PROPER PRECAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL INJURY.
Both the front blower motor resistor and the optional rear heater-A/C unit blower motor resistor can be diagnosed using the procedure that follows. For circuit descriptions and diagrams, refer to Air Conditioning/Heater in Group 8W - Wiring Diagrams.
  1. Disconnect and isolate the negative battery cable.
  2. Disconnect the wire harness connector from the blower motor resistor block.
  3. Check for continuity between each of the blower motor switch input terminals of the resistor and the resistor output terminal. In each case there should be continuity. If OK, repair the wire harness circuits between the blower motor switch and the blower motor resistor block or blower motor as required. If not OK, replace the faulty blower motor resistor block.
Here is the information on replacing the resistor:

REMOVAL
  1. Disconnect and isolate the battery negative cable.
  2. From the passenger foot well area, remove the two hex screws used to secure the blower motor resistor.
  3. Unplug the front blower motor resistor from the wire harness connector.
  4. Remove the front blower motor resistor from the HVAC unit.
Here is an exploded view of the HVAC box. The resistor is #63 in the picture and the actual part may appear slightly different:

spacer.gif 1100_024_0003.gif spacer.gif spacer.gif View Full Image spacer.gif


If any issues such as no voltage at blower connector or damaged or melted connector at the resistor then let me know.

Oct 19, 2008 | 2002 Dodge Durango

1 Answer

Blower control


I had the same dead blower problem, the resistor was corroded. It´s under the dashboard on the passenger side.

Jun 18, 2008 | 1997 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...