Question about 2009 Chevrolet HHR

1 Answer

Po340 and jerky motion 09 hhr

Jerky motion and po340 on 09 hhr i have replaced the cam pos sensor

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 3 Answers

Http://www.chevyhhr.net/forums/problems-service-repairs-42/reduced-engine-power-engine-shutdown-error-code-p0340-p0601-47411/page2/ Reduced engine power engine shutdown error code P0340 and P0601 Chevy...

Posted on Jun 22, 2014

Ad

4 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
j_del

Jeremy Dellow

  • 1586 Answers

SOURCE: If the Correlation between the

It could be a fault with one or both of the sensors (they can and do fail occasionally). If both sensors are good and the wiring to them is ok, then your timing belt has likely jumped at least one tooth.

Posted on Aug 06, 2011

airjer995

Jeremy W.

  • 5332 Answers

SOURCE: 2006 hhr 2.4 won't start after replacing both camshaft position sensors.

Did you remember to plug in the MAF sensor? Are you sure the air chamber is correctly installed on the throttle body?

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Posted on Feb 19, 2012

ercupa190

ernesto cuadra

  • 12223 Answers

SOURCE: PO340 code replaced cam sensor and 2 days later same code came back on.

test with the scanner+computer the diagnostic system. Otherwise the time+money can be waste. Go to the dealer and test it.

God bless you

Posted on Jul 05, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Code p0340, p0462 on subaru outback 2001


Po340 is a cam shaft sensor and po462 is low voltage on your fuel guage. So i assume you are haveing fuel level issues. If you can turn wrenches you can do these repairs yourself. Just do a google search and you can get some youtube videos of sensor replacement and location. Have fun.

Aug 29, 2014 | 2001 Subaru Outback

1 Answer

Codes po340 2004 Sebring


DTC code is P0340 no cam signal at PCM. Chrysler always used to say replace the cam and crank sensors together..wouldn't pay our warranty time at dealer unless we replaced both.

Aug 21, 2014 | 2004 Chrysler Sebring

1 Answer

Code po340,change coil,cam sensor,still got code,missing


that is the code for cam position. . when you replaces the sensor did you clean the cam,and replace the seal. what motor do you have

Dec 09, 2012 | 1996 Chrysler Town & Country

1 Answer

Code po340 2002 p/t cruser


you can do 1of two things 1pull the cam sensor out and clean it up and reinstall it to see if that works or you can replace it with a New one, this is what the code po340 means that you have a problem with the cam sensor

Dec 01, 2010 | Chrysler PT Cruiser Cars & Trucks

1 Answer

2003 Hyundai Sonata starts when cold and dies after warming up.


Wiring problem or the ECU (engine control unit) is defective. Try this, disconnect the battery cables from the battery and short/touch them together for 30 seconds (do not do this if connected to the battery). Then, reconnect the cables to the battery posts & see if that fixes it. If it doesn't, then there is a wiring problem associated with the cam pos snsr or the ECU has gone bad.

Aug 11, 2009 | 1992 Hyundai Sonata

2 Answers

DTC - PO340, PO325


My Nissan micro 2004 model just stopped in the middle of the road one day then the engine management light came on, anyway took it to my local garage TWK Thomas who said it was a cam shaft sensor problem. OK so sensor was put on, engine management light went off for two days only. So went back to the garage they said that another sensor should be fitted on the opposite side. And then the problem should be rectified, but i had given the £160 for this problem to be fixed the first time. I decided it was time to take it to another garage Nis Tec they put it on the computer and a code po340 came up would this mean another sensor or the cam chain has stretched please help. ...claire

Jul 09, 2009 | 1998 Nissan Maxima

Not finding what you are looking for?
2009 Chevrolet HHR Logo

846 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...