Question about 2007 Kia K2700 Workhorse

2 Answers

HOW TO DO TIMMING FOR KIA K2700 WORKHORSE

TIMMING GEAR

Posted by Anonymous on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

ALIGN THE TIMING MARKS AS PER THE ATTACHED FOTO. on the gears there are timing marks.
HOW TO DO TIMMING FOR KIA K2700 WORKHORSE - timming-kia-k2700-workhorse-bm2ho3s54k4dok42ylsl0luo-2-0.jpeg

Posted on Nov 11, 2014

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

The timing diagram for kia k2700 is the same like for a kia j2?

Posted on Jun 22, 2016

  • Gabriel Aug 07, 2016

    At what said mast the kewhay stand when the mump is taken aut

×

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to set timming chain after replaceing timming chain tentioner?.


if you did not turn the engine over while you had the chain off the timing did not change. if you did there is a dot on the cam gear and the crank gear line them up and you'll be in time

Nov 12, 2015 | Cars & Trucks

1 Answer

4jx1 camshaft marks on isuzu trooper 2001 3,0 dohc engine


the timming gear that the belt runs on has a mark (V cut in gear) to rear cover at about 12 o clock and crank pulley has timming mark for top dead centre, both cams have cut outs in rear that a special tool (camshaft stopper 5-8840-2592-0) locks into to hold cams in correct position, but can do without this, if the cam belt gear is off, the keyway should be at 12 o clock. the marks in the camshaft gears (dots) is for assembly of sissor gears to solid gears on camshafts that run together and they should match up only if you had this appart.

stevenhurc_12.jpg no.1 is timming mark

stevenhurc_13.jpgthis is the locking plate tool

Apr 19, 2011 | 2001 Isuzu Trooper

1 Answer

2002 mazda 626 replacing timming belt need to know where timming mark are and where to turn them ///v-6 dohc


TIMING MARKS SHOULD BE A NOTCH ON THE CAM GEAR, AND ONE ON THE CRANK GEAR! THEY SHOULD BE LINED UP FACING EACH OTHER!

Feb 22, 2011 | 1999 Mazda 626

1 Answer

Trying to put a timming chain on a 2.2 like to know where the timming marks are or details to make sure we doing it right


mak sure the dot on crank gear is at 12 oclock and the dot on the cam gear is at 6 oclock.or just make sure the dots line up when the chain is in place.dot to dot.

Feb 05, 2011 | Chevrolet S 10 Cars & Trucks

1 Answer

Cam timming marks to set up the timming chain and cam timming.


Should be a dimple or dot on each gear crank one points up cam one points straight down they should line up perfecly.

Nov 09, 2010 | Jeep CJ7 Cars & Trucks

1 Answer

My cam shaft timming gear and my crank shaft timming gear dots line up and my harmonick balancer timming mark is on 0 which way should my rooter button face towards number 1 or towards rear of engine


The rotor should be pointing close to number 1, but keep in mind that the spark is actually supposed to happen before the piston gets to tdc so the rotor will be a little bit past the number 1 terminal when the crankshaft indicates that you're at tdc.

Feb 04, 2010 | 1994 Chevrolet K1500

1 Answer

Suzuki baleno 2002


The problem is else where,they have enclosed t/chain,the belt drives the water pump,altinator,power steering etc.,The engine should be checked by a professional for other problems,should not be driven or run without the drive belt in place.

Dec 27, 2008 | 2003 Suzuki Aerio

1 Answer

Timming belt


Inside of the top gear there is a hash mark, you need to turn the gear so that the hash mark is top center. (you need a second person to help you for the next step.) You then have to take the first spark plug out and stick a long screw driver inside of the hole. You then have to turn the bottom gear until the first cylinder comes all the way up. You then put the new belt on the car without moving the two gears.

Dec 02, 2008 | 1997 Mercury Mystique

Not finding what you are looking for?
2007 Kia K2700 Workhorse Logo

Related Topics:

1,747 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...