Question about 2003 Mitsubishi Lancer
I have a 2003 Mitsubishi Lancer 2.0L and the alternator belt snapped. I have successfully removed the serpentine belt but im not sure how to loosen the tension on the alternator to install the new alternator belt.
I diagram or an accurate description of which bolts to loosen would be ideal
I have not seen this vehicle but, the center bolt or nut that holds the tensioner to the block is backed off two turns first.
Then the adustment bolt (most are accesed from under the vehicle) can be adjusted to give enough slack to install the new belt.
If this is still too tight, remove one of the two or two of the three bolts that mount the Alternator to allow for another 1/8" and install the belt.
Then remount the Alternator.
Then readjust the tension bolt.
Finish with the bolt or nut that mounts the tensionor to the block.
Posted on Jun 28, 2009
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Tips for a great answer:
Excessive belt tension will cause damage to the alternator and water pump pulley bearings, while, on the other hand, loose belt tension will produce slip and premature wear on the belt. Therefore, be sure to adjust the belt tension to the proper level.
To adjust the tension on a drive belt, loosen the adjusting bolt or fixing bolt locknut on the alternator, alternator bracket or tension pulley. Then move the alternator or turn the adjusting bolt to adjust belt tension. Once the desired value is reached, secure the bolt or locknut and recheck tension.
Fig. . . . then remove the alternator belt from the engine
Fig. . . . then remove the power steering belt from the engine
Fig. Accessory V-belt routing-Mitsubishi 3.5L and 1998-00 3.0L SOHC Galant engines
ALTERNATOR AND A/C COMPRESSOR
Mar 21, 2013 | 1996 Mitsubishi Mirage
Oct 25, 2011 | 2008 Mitsubishi Lancer GTS CVT Sedan
Apr 13, 2011 | 2002 Mitsubishi Lancer
Locate the two belts on the left side (passenger side) of your Mitsubishi Lancer. The outer belt is a serpentine belt, operating four pulleys and the inner belt is your alternator belt.
Follow the serpentine (outer) belt to the three pulleys lined up vertically near the front of the engine compartment. Locate the middle pulley, which is the tension pulley for the belt.
Loosen the bolt on the middle pulley with a socket wrench by turning counter-clockwise. Do not remove the bolt, just turn it a couple of times. Loosen the tensioner bolt on the side of the of the pulley, facing the front of the vehicle.
Remove the serpentine belt and then loosen the bolt on the alternator. With the alternator loose, move it forward so that the alternator belt loosens up and then remove belt from the pulleys.
Install the new alternator belt by placing it over both inside pulleys. Tighten the tension on the alternator belt by moving the alternator back and keeping tension on it by holding it back with a long screwdriver. While the alternator belt is tight, use a socket wrench to tighten up the bolt on the alternator.
Place the serpentine belt back on the pulleys and then use a socket wrench on the bolt on the front of the tension pulley. Once the serpentine belt is tight, tighten up the bolt in the middle of the tension pulley.
Start the Mitsubishi Lancer's engine to test the alternator belt and make sure it is working properly. Once you have verified it is working, turn the engine off.
Oct 08, 2010 | 2002 Mitsubishi Lancer
Aug 18, 2010 | Mitsubishi Lancer Cars & Trucks
Aug 02, 2010 | 2003 Mitsubishi Lancer
Oct 10, 2009 | 2004 Mitsubishi Lancer
Mar 07, 2009 | 2003 Mitsubishi Lancer
770 people viewed this question
Usually answered in minutes!