Question about 1996 Lexus ES 300

Open Question

What value do you torque the valve cover bolts on a 1993 ford temple 2.3 engine

Posted by Anonymous on

Ad

1 Suggested Answer

George Obray

  • 271 Answers

SOURCE: Valve cover and Oil pan bolt torque

Inside to outside for torque pattern, 7 foot lbs. or 144 inch lbs.

Posted on Oct 24, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the torque spec for the cylinder valve cover 2004 toyota sienna?


20. INSTALL CYLINDER HEAD COVER SUB-ASSY
(a) Apply seal packing to the cylinder head as shown in the
illustration.
Seal packing: Part No. 08826-00080 or equivalent
NOTICE:
 Remove any oil from the contact surface.
 Install the cylinder head cover within 3 minutes after
applying seal packing.
 Do not start the engine within 2 hours after installing.
(b) Install the cylinder head cover with the 9 bolts. Tighten the
bolt uniformly in several steps.
Torque: 8.0 Nm (80 kgf cm, 71 in.lbf)
(c) Install the engine wire harness with the 3 nuts.
Torque: 8.4 Nm (85 kgf cm, 74 in.lbf)
21. INSTALL CYLINDER HEAD COVER SUB-ASSY LH
(a) Apply seal packing to the cylinder head as shown in the
illustration.
Seal packing: Part No. 08826-00080 or equivalent
NOTICE:
 Remove any oil from the contact surface.
 Install the cylinder head cover within 3 minutes after
applying seal packing.
 Do not start the engine within 2 hours after installing.
(b) Install the cylinder head cover with the 9 bolts. Tighten the
bolt uniformly in several steps.
Torque: 8.0 Nm (80 kgf cm, 71 in.lbf)
(c) Using an E6 torx) socket wrench, install the engine wire
harness protector with the 2 bolts.
Torque: 8.4 Nm (85 kgf cm, 74 in.lbf)

This is year/make/model specific to the 2nd Gen Sienna. Taken from the 05 Toyota Sienna repair manual. Hope this answers your torque specs for the valve covers which uses 10 mm bolts. If in doubt, as Scotty Kilmer asserts, do a "German tight".

Nov 20, 2017 | 2004 Toyota Sienna

1 Answer

What is the torque value for valve cover gasket on 2004 jeep grand cherokee


torque settings (inch lbs etc) on the valve covers
well what engine, must we magically guess that.
but no matter, that, ive posted the FSM factor manual here over 300 times now, from 93 to 2012 and more.
the manual for the WJ is free.
will cost you 2 finger clicks is that costly?

http://www.factorychryslerparts.com/products/Jeep/2012/Grand-Cherokee/VALVE-Linear-Purge--Without-Bracket/4281710/04891739AA.html


now click engine.
2 engines
read the one that matches yours.
the torque on every bolt./nut and screw is there,
as is on all jEEP books.
its the real book, not fake its a real JEEP book
cost free. what could be better, you tell me. official book.

Oct 21, 2016 | 2004 Jeep Grand Cherokee

1 Answer

Head bolts torque settings for 1993 ford taurus 3.0 engine


These are the torque valies and sequences for your engine
Torque in 2 steps [1st (33-41 ft-lbs),
2nd (63-73 ft-lbs)]


Torque sequence: (for each bank)
------------
6 4 2 8

5 1 3 7
------------

Good luck and please rate this solutuon

May 21, 2011 | Ford Taurus Cars & Trucks

2 Answers

Rebuilding 4.2 v6 ford need torque spec for main bearing


V8 Engines Component Torque Camshaft Sprocket Bolt 40-45 ft. lbs. Camshaft Thrust Plate-to-Engine Bolts 9-12 ft. lbs. Crankshaft Pulley-to-
Vibration Damper Bolts 35-50 ft. lbs. Cylinder Head Bolts All Except 1993 Flanged Bolts Step 1 55-65 ft. lbs. Step 2 65-72 ft. lbs. 1993 Flanged Bolts NOTE 1 Exhaust Manifold Bolts All Except 1993 HO Cobra 18-24 ft. lbs. 1993 HO Cobra 26-32 ft. lbs. Flywheel/Driveplate-to-
Crankshaft Bolts 75-85 ft. lbs. Intake Manifold Bolts Note 2 Upper Intake Manifold-to-
Intake Manifold Bolts 12-18 ft. lbs. Main Bearing Cap Bolts 60-70 ft. lbs. Oil Filter Insert-to-Engine Adapter Bolt 20-30 ft. lbs. Oil Pan 1979 Step1 Large Bolts 11-13 ft. lbs. Small Bolts 7-9 ft. lbs. Step 2 Large Bolts 15-17 ft. lbs. Small Bolts 10-12 ft. lbs. 1980-87 9-11 ft. lbs. 1988 and up 6-9 ft. lbs. Oil Pick-up Tube-to-Main Bearing Cap Nut 22-32 ft. lbs. Oil Pick-up Tube-to-Oil Pump Bolts 1979-87 10-15 ft. lbs. 1988 and up 12-18 ft. lbs. Oil Pump Bolts 22-32 ft. lbs. Rocker Arm Fulcrum Bolts 18-25 ft. lbs. Thermostat Housing-to-Engine Bolts Through 1987 9-12 ft. lbs. 1988 and up 12-18 ft. lbs. Timing Chain Cover Bolts 12-18 ft. lbs. Valve Cover Bolts 10-13 ft. lbs. Water Pump Mounting Bolts 12-18 ft. lbs. NOTE 1 Step 1 Tighten bolts in sequence to 25-35 ft. lbs. Step 2 Tighten bolts in sequence to 45-55 ft. lbs. Step 3 Tighten bolts in sequence an additional ¼ turn. NOTE 2 Step 1 Tighten bolts in sequence to 23-25 ft. lbs. Step 2 After assembly, retorque all bolts in sequence to 23-25 ft. lbs.let me know if this helps and how about a rating.

Apr 23, 2011 | Ford F-150 Cars & Trucks

1 Answer

Timing Chain Replacement procedure steps


1. Jack up front of vehicle and support on safety stands. Remove left front wheel.
2. Remove alternator/water pump drive belt. Remove water pump pulley.
3. Remove A/C belt if equipped.
4. Remove valve cover.
5. Remove upper timing belt cover.
6. Rotate crankshaft until No. 1 cylinder is at TDC compression stroke and camshaft sprocket timing marks align with edge of cylinder head. "UP" cast on sprocket will be at top when sprocket is in correct position. Crankshaft may be rotated using a socket wrench inserted through access hole in left fender well (engine rotates counterclockwise).
7. Unbolt and remove crank pulley. Remove rubber seal washers from belt tensioner pivot and adjustment bolts protruding through lower belt cover. Remove belt cover retaining bolts and remove cover from below.
8. Remove concave belt retainer from end of crankshaft. If timing belt is to be reused, mark direction of rotation before removing.
9. Loosen belt tensioner pivot and adjustment bolts. Push tensioner away from belt and retighten adjustment bolt to hold tensioner in this position. Remove belt.
10. Insert a suitable tool through cam sprocket and brace against cylinder head. Remove bolt and pull sprocket from camshaft.
11. Without dislodging key, install new sprocket on camshaft. Torque bolt to 22 ftlb (30 Nm).
12. Install new timing belt by starting at crank gear and working it over cam sprocket in clockwise direction. Ensure that timing marks are properly aligned.
13. Release tensioner by loosening adjustment bolt. After tensioner contacts belt, retighten bolt.
14. Rotate engine at least one full turn (counterclockwise) and check that timing marks are aligned. Loosen adjustment bolt and allow tensioner to take out any remaining belt slack. Torque adjustment and pivot bolts to 22 ftlb (30 Nm).
15. Install remaining components in reverse order of removal. Torque fasteners to following values:

TORQUE VALUES

Valve Cover Nuts - 7 ftlb (10 Nm)
Cam Sprocket Bolt - 22 ftlb (30 Nm)
Tensioner Pivot Bolt - 22 ftlb (30 Nm)
Tensioner Adjust Bolt - 22 ftlb (30 Nm)
Belt Cover Bolts - 7 ftlb (10 Nm)
Crank Pulley Bolt - 83 ftlb (115 Nm)
Water Pump Pulley Bolts - 9 ftlb (12 Nm)

daves944_3.jpg

Dec 19, 2010 | 1983 Honda Accord

1 Answer

What is the toqrque spechs and order for a Northstar 4.6 engin for both head and main & rod barngs. Does the main barnings have a order


If you have to pull a cylinder head on a 1993-1999 4.0L or 4.6L Northstar V8 to replace a gasket or do a valve job, do not reuse the old 11mm head bolts. Also, GM has revised the head bolt torque values and tightening procedure as follows:
  1. In sequence, torque all bolts to 30 ft.-lbs.
  2. In sequence, rotate all bolts an additional 70 degrees.
  3. In sequence, rotate all bolts an additional 60 degrees.
  4. In sequence, rotate all bolts another 60 degrees.
  5. Torque the front three M6 head bolts to 106 in.-lbs.

Dec 09, 2010 | 2003 Cadillac Seville

1 Answer

1998 FORD FESTIVA HEAD BOLT TORQUE SETTINGS & TIGHTENING SEQUENCE (1.5 LITRE ENGINE)


1978 - 1980 FORD FESTIVA 1.6L 65-70 Foot pounds (Final torque)
Torque sequence 9 3 1 5 7 8 6 2 4 10 Step 1: torque to 5 Ft/Lbs Step 2: torque to 20-30 Ft/Lbs Step 3: torque to 50-55 Ft/Lbs Step 4: torque to 65-70 Ft/Lbs Recheck final torque in sequence


1988 - 1993 F0RD FESTIVA 1.3L
Torque sequence front of engine 8 4 1 5 9 7 3 2 6 10 Step 1: torque to 35-40 Ft/Lbs Step 2: torque to 56-60 Ft/Lbs Recheck final torque in sequence

2011 FORD FESTIVA 1.6L NO TORQUE SPECS AVAILABLE THERE IS NO FORD FESTIVA MANUFACTURED IN 1998 ALSO NO FORD FESTIVA MANUFACTURED WITH A 1.5L ENGINE
HOPE THIS HELPS YOU

Aug 06, 2010 | Ford Focus Cars & Trucks

1 Answer

93 ford aerostar 4.o engine head bolt torque


step one is 22 ft lbs.
step two is 52 ft lbs
step #3 is turn an additional 90 degrees. sart in the middle and work your way out going top tobottom, good luck.

Nov 03, 2009 | 1993 Ford Aerostar Extended

3 Answers

1992 Toyota Previa van,Oil dripping onto exhaust manifold, replace head gasket? need a free manual!


The toyota previa uses a formed silicone gasket for the valve cover and the cover is held in place by metric shoulder bolts ( 10mm). The valve gasket leaks because you can't get enough preload on the bolts to re-seat the old gasket when it gets old and shrinks. The shoulder bolts only allow you to tighten the gasket enough to seat the shoulder on the bolt. If you continue to torque down the suspected bolts, you will snap the bolt off ( don't ask me how I know this ). You can either 1.)replace the old gasket with a new one or 2.) remove the existing bolts around the leak area and put in new metric bolts that do not have a shoulder. You may want to put in a small sleeve into the existing bolt hole but shorter than the thickness of the valve cover to account for the smaller diameter bolt. You can now torque down the bolt and get enough preload to seal the valve cover without removing the old gasket. Make sure you use a torque wrench ( in-lbs) or be very careful not to snap these small valve cover bolts.

May 26, 2009 | 1992 Toyota Previa

Not finding what you are looking for?
1996 Lexus ES 300 Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...