Question about 1995 Ford F150 Styleside Regular Cab

Open Question

1995 ford f-150 5.8liter ignition wiring schematics free

Truck has no spark and no injector pulse

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 18 Answers

SOURCE: 2000 F 250 WILL NOT START CRANKS OVER ONLY.

you should have the pcm scanned for dtc's... probably a bad crank or cam sensor

Posted on Oct 25, 2008

Ad

Anonymous

  • 255 Answers

SOURCE: Ford 1995 F150 Truck. Turn ignition key off but Truck still runs

ignition switch electrical portoin above brake pedal on steering column

shack

Posted on Apr 14, 2009

Anonymous

  • 1 Answer

SOURCE: 1981 ford truck alternator schematic

replace an alternator on a 1981 ford f-150

Posted on Aug 05, 2009

rip_forhees

  • 1 Answer

SOURCE: wiring schematic for 1995 ford

Is there a fusible link on the starter of a 1997 Ford Ranger, 2WD, 4.0 L

Posted on Dec 20, 2010

emissionwiz

Marvin

  • 85222 Answers

SOURCE: 2003 FORD TAURUS 3.0 VIN S LOST INJECTOR PULSE,

Hello
Have you run the OBD2 electronic engine control fault code test? both the of the tests must be done and the result's diagnosed, that is the key on engine off test (KOEO) and the key on engine running test (KOER) as well. How have you confirmed the injector pulse is lost? each injector has its own driver in the PCM (Powertrain Control Module), the injector grounds the injectors to open them in the proper sequence, it is the same as the firing order of the spark plugs. To confirm loss of injector pulse you use a little tool known as a "NOID", they can be bought at any good auto parts store for about $5.00, they contain a little light that flashes when the injector pulse is present, it plugs into the harness connector at each injector. Each injector shares the same Battery (+) circuit and is powered off of a fuse and it in turn is powered off the ignition starter switch.

Posted on Mar 28, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Getting no injector pulse in my 1991 ford escort.


Do you have power going to the injector ? And do you have spark to the plugs ? The computer uses the crank signal from the distributor to know when to fire the injector.

Jul 06, 2013 | Cars & Trucks

1 Answer

2000 Dodge Grand Caravan only have two injectors pulsing?


I would check the wiring harness for the injectors

Should have 12 volts with key on-- to all injectors,same
as the ignition coils

Ignition or Injectors are turned on by PCM Drivers

Do not put any voltage to injectors they are pulsed

Dec 20, 2012 | Cars & Trucks

1 Answer

Why does the fuel injector receive no pulse for 1998 ford explorer 4.0 motor


The 6 cyclinder motor has 6 fuel injectors. If your not getting pulse Electrical grond to an injector wire theirs a likly chance your not getting it at another. If your getting no pulse at all the engine won't run. Does the check engine light on with the engine running? What meadod did you determine that it had no pulse? Remove one injector wire one at a time with the engine running? If it's not running at all then the no pulse can be a common system part like the crank senser. Does the engine get spark? Most of the time pulse and spark are hand in hand so if the crank senser were bad it's not going to have s[ark either.

Dec 02, 2010 | 1998 Ford Explorer

1 Answer

How to dissable the injectors and the ignition on a ford focus


Cut the pulse wire from the ECU to the coil, this will shut off injectors and spark.

Dec 01, 2010 | 2008 Ford Focus

1 Answer

Looking for wiring schematics for 1995 chev kodiak 6500.need to trace wiring.. i have no ground to ground side of coil.intake heater is fine. need help


the coil receives power all the time with key on, the ground side is toggled to make the coil spark, you shouldn't be able to detect ground unless its running and if you do ground it while running you will find it will die. the pickup coil, and ignition module in the distributor control the spark, and injector pulse, if it won't spark, and its the origional distributor, I usually just replace the whole thing with a reman from carquest, napa, etc, usually 100 to 150 with exchange, its cheaper than replacing the separate parts, and all new you can't go wrong. this is a common problem with any mid 90's gm v8

Oct 29, 2010 | Chevrolet Chevy Cars & Trucks

1 Answer

Firing Order diagram for 2006 Ford Explorer


Hope this helps. The ignition coil:
  • changes low-voltage pulses from the PCM to high-voltage pulses.
  • fires 2 spark plugs simultaneously.
  • has 3 transformers.
    • One transformer fires the spark plugs for cylinders 1 and 5
    • One transformer fires the spark plugs for cylinders 2 and 6
    • One transformer fires the spark plugs for cylinders 3 and 4
Spark plug wires:
  • carry high-voltage pulses from the ignition coil to the spark plugs.
The spark plugs:
  • change high-voltage pulses to spark at the gap, which ignites the fuel and air mixture.
The firing order is 1-4-2-5-3-6.

69efa96.jpg

Jun 06, 2010 | 2006 Ford Explorer

1 Answer

Cranks but will not start.


You need to verify fuel injector pulse and fuel pressure. then verify ignition spark.
Possible causes are the fuel pump, cam or crank sensor, Anti Theft system.

Mar 19, 2010 | 1995 Ford Mustang

1 Answer

Cranks no spark has injector pulse 1994 4.3 v-8


The ignition module is probably bad replace it.

Nov 05, 2009 | 1995 Chevrolet Impala

1 Answer

1990 gmc 6500 topkick with no spark or injector pulse. all 4 wires on the ignition coil have battery voltage with key on. is coil shorted or is the ignition module bad?


You are jumping to conclusions. Slow down.
No spark AND no injector pulse indicates none of the desired outputs were triggered. The ignition module makes spark when it receives a crankshaft position sensor signal, and then transfers control of that spark to the computer after it starts. The module takes its crank sensor signal and generates an RPM count that it forwards to the PCM(main computer) which is used for triggering the injectors and controlling timing. SO, if you had a bad crank sensor OR a bad ignition module, you could lose both spark AND fuel. a coil would not disable injector pulse. modules RARELY fail in a manner that disables RPM reference to the computer causing it to not fire the injectors...At this point, I would TEST the crank sensor as the next step. If its easier, 1 of the wires on the module goes directly there so you can test the crank sensor at the module.

Sep 18, 2009 | 1990 GMC K3500

1 Answer

I have a 92 Ford Aerostar no injector pulse!


OK YOU HAVE SPARK IN THE WIRES AND YOU DO HAVE GAS TOO AND THE CAR DOESNT START OR THE ENGINE DOESNT TURN OVER

Jul 30, 2009 | 1992 Ford Aerostar Extended

Not finding what you are looking for?
1995 Ford F150 Styleside Regular Cab Logo

Related Topics:

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85219 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...