Question about 2004 Ford Explorer Sport Trac
Posted by Anonymous on
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
This problem is most times caused by an open circuit in the rotating contact under the steering wheel, this part is called the clock-spring contact, it supplies a connection to the airbag and steering wheel controls like the cruise, horn and radio controls. I would check the fuse as well to cover the bases, it is fuse #9 in the passenger compartment fuse box, it is a 7.5 AMP
Posted on Oct 21, 2008
I'm guessing you have disc brakes in the front of the Explorer. If so, you need to unscrew the two bolts that hold the caliper on.(they'll be either hex or allen bolts) If the caliper does not slide off, take a C=clanp and slowly back the piston down on the caliper. This should free up the caliper so that it can be removed. Make sure you grease the slider pins for the caliper when you reassenble.
Posted on Dec 30, 2008
You may want to check the relay that goes to the primary window. This will provide support to all the other windows. However, it may not just be the window relay, it could possibly be that between your window relay and your main switch there is a short or cut wire that is causing this problem. Unfortunately, you may need to visit your Ford Dealership to run a diagnostic on your wire or if you know an electronic shop that can run one to see if it is receiving and sending power. Have them check the main door fuse and window assembly to see that you are getting power.
Posted on Mar 19, 2009
Press and hold the SELECT/RESET
control switch to select SYSTEM
CHECK when “SYSTEM CHECK /
HOLD RESET” is displayed in the
message center. Selecting this
function from the SETUP MENU
causes the message center to cycle through each of the systems being
monitored. For each of the monitored systems, the message center will
indicate either an OK message or a warning message for two seconds.
Pressing the SELECT/RESET control switch cycles the message center
through each of the systems being monitored.
The sequence of the system check report and how it appears in the
message center is as follows:
1. OIL LIFE RESET
2. CHARGING SYSTEM
3. WASHER FLUID
4. DOOR AJAR
5. EXTERIOR LAMP
6. BRAKE SYSTEM
7. PARK BRAKE
8. MILES TO EMPTY
9. FUEL LEVEL LOW (will only display if 50 miles or less to empty)
To reset the oil monitoring system to 100% after each oil change
[approximately 5,000 miles (8,000 km) or 180 days] perform the
1. Enter SYSTEM CHECK to display
“OIL XXX% RESET IF NEW”.
2. Press SELECT/RESET control
switch to display “HOLD RESET IF
3. Press and hold the
SELECT/RESET control switch for
more than 2 seconds. Oil life is set
to 100% and “OIL CHANGE SET TO
100%” is displayed.
Posted on Apr 02, 2009
They will not loan you the tools.....how else will they continue to rip off the average garage junkie and make lots of money?
Posted on Nov 18, 2009
Tips for a great answer:
Mar 09, 2018 | Ford Cars & Trucks
Nov 04, 2017 | Ford Cars & Trucks
Jan 15, 2013 | 2007 Ford Explorer Sport Trac
Aug 27, 2011 | 2004 Ford Explorer Sport Trac
May 06, 2011 | 2004 Ford Explorer Sport Trac
Jul 26, 2010 | 2001 Ford Explorer Sport Trac
Dec 16, 2009 | 2003 Ford Explorer Sport Trac
Oct 20, 2009 | 2004 Ford Explorer Sport Trac
91 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: