Question about Cars & Trucks

1 Answer

What are the torque specs for front struts on 2002 honda odyssey

I need the torque specs for the top 3 bolts of the front struts as well as the bottom two bolts

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Cars & Trucks Master
  • 755 Answers

Just tighten them by hand with a wrench pretty tight , just do not snap them off , you do not need the specs make them tight where as they will not back out , no bigger

Posted on Sep 15, 2014

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
chuck943

Chuck Martin

  • 783 Answers

SOURCE: Head bolt torque specs needed for 96 tbird 3.8

Head bolts are torque to yeild so you MUST use new bolts.
Tighten cylinder head retaining bolts in numerical sequence in three steps as follows:

  1. 20 Nm (15 lb-ft).
  1. 40 Nm (30 lb-ft).
  1. 50 Nm (37 lb-ft)
Loosen retaining bolts one at a time two to three revolutions and retighten as follows:

Long bolts:
  • Tighten to 40-50 Nm (30-37 lb-ft).
  • Rotate an additional 175-185 degrees.
  • Go to next bolt in sequence.
Short Bolts:
  • Tighten to 20-30 Nm (15-22 lb-ft).
  • Rotate an additional 175-185 degrees.
  • Go to next bolt in sequence.
Here is a pic of the sequence
http://i253.photobucket.com/albums/hh43/chuck943/Headboltsequence38L.gif

Posted on Mar 19, 2009

GIVHRR

  • 72 Answers

SOURCE: Front Hub Bearing Torque specs to complete replacement

THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Posted on May 09, 2009

outdoorsman5

outdoorsman5

  • 631 Answers

SOURCE: head bolt torque specs for 2000 dodge neon 2.0 SOHC

I have the specs and diagrams. If you want me to send them to you, give me your email address. Outdoorsman592003@yahoo.com

Posted on Sep 05, 2009

inspectmycar

Chris Biddle

  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

Toyota Ed

  • 1861 Answers

SOURCE: need torque specs for a 2002 toyota camry 2.4 for

The 2002 2.4 engine head bolts are 'torqued to distance'.

First, install all the bolts, and, in a sequential fashion, starting at the innermost, working outward, torque all bolts to 70 N-m/806 kgf-cm/58 foot lbs.

Next, mark the front side of each head bolt with a dot of paint. Retighten te cylinder head bolts 90 degrees, starting at the inner 2, and working outward.

We hope that this helps you out.

Posted on Dec 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the toque spec for a 2010 RX350 front suspension coil top 3 nut bolt and the bottom 2 bolt.


I, feel sorry for you, after reading your problem, but don't worry you visit the Reliable-Store they will help you for sure.
Best Manuals

Oct 01, 2016 | 2010 Lexus RX 350

1 Answer

Valve Cover Torque Specs


hi valve covers are never more the 8 to 10 nm newton meters start in the middle one across from each other then criss cross one on the top right then to the left bottom ,then top left,right bottom work your way out till they are all done cant be too tight or it will squish the gasket and cause leaks danny

Apr 21, 2014 | 2002 Honda Accord

1 Answer

2003 honda odyssey 3.5 head bolt torque spec


Apply new engine oil to the threads and flanges of the cylinder head bolts.

Tighten the cylinder head bolts sequentially in three steps.

NOTE: Perform each step twice.

1st step torque: 39 Nm (4.0 kgf-m, 29 ft. lbs.)
2nd step torque: 69 Nm (7.0 kgf-m, 51 ft. lbs.)
3rd step torque: 98.1 Nm (10.0 kgf-m, 72.3 ft. lbs.)

Feb 28, 2014 | 2000 Honda Odyssey

1 Answer

How to cange front shocks.?


Raise and support the car safely and remove the front wheels. Undo the clip holding the brake line to the strut. Loosen the bolts holding the strut to the steering knuckle. Before removing them, remove the strut mount tower bolts under the hood. Then remove the other bolts, the entire strut assembly will slide out. You can either install a complete new strut and spring assembly (more expensive), or you can use a coil spring compressor to remove the spring from the old strut and install it on a new strut (less expensive but a lot more work, and you must have access to a spring compressor). Make sure when installing the spring that it is aligned correctly on the new strut. Also, you should replace the strut mounts with new ones. Be aware that a compressed spring is very dangerous, so be sure to follow the instructions for the spring compressor. Re-install the strut assembly. Make sure that the knuckle bolts and strut mount bolts are torqued to spec.

Mar 28, 2010 | 1990 Honda Accord

1 Answer

Need to replace Serpentine belt and p/s belt on my 2002 honda odyssey is this complicated?


the procedure is as follows:-- You have to do it from underneath the vehicle. Take off the rivets to the two plastic covers, and then you will be able to see the tensioner for the belt. Use a 3/4 inch wrench on the tensioner (don't put it on the bolt that holds the tensioner on), and pull it toward the vehicle. The belt will loosen, and you can take it off. As a car owner, you know how important the belt tensioner is for your 2002 Honda Odyssey. However, internal parts wear and damage will loosen or seize the tensioner wheel, causing the belt to slip and make noise. Eventually, the belt may break, shut down the engine and lead you into a serious traffic accident. Before that happens, replace the tensioner on your Honda model and save yourself a lot of problems:---- Remove the Drive Belt:-- 1)Look for the drive belt routing diagram on your vehicle's engine compartment. This is a black and white label, about 4 by 6 inches, usually attached to the radiator shroud or near the strut towers inside the engine compartment. This diagram will be your guide when reinstalling the drive belt. If cannot find one, make a simple sketch on a piece of paper. 2) Insert a belt-tension release tool, or similar tool, into the auto-tensioner arm. 3)Rotate the auto-tensioner arm counterclockwise and slip the belt off the tensioner pulley. 4) Release the auto-tensioner but do not let it snap back in place. 5) Remove the drive belt from the engine compartment. Replace the Belt Tensioner 1) Unscrew the two auto-tensioner mounting bolts using a ratchet, ratchet extension and socket. Note the location of each bolt because they are of different size. 2) Remove the old auto-tensioner from the engine compartment. 3) Set the new auto-tensioner in place and start the two mounting bolts by hand. Make sure you install the bolts in their original place. 4) Start tightening the bolts until they hit the stop using the ratchet, ratchet extension and socket. 5) Torque the two bolts using a torque wrench. Torque the small bolt to 16-foot pounds [22 Nm] and the large bolt to 47-foot pounds [64 Nm]. This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya

Mar 01, 2010 | 2002 Honda Odyssey

4 Answers

Torque specs for 96 Honda Accord 2.2L


the main bearings bolts is to 1st step 30Nm or 22lbs ft and the last step is 75Nm or 54lbs ft in this tighten secuence. 9 3 1 5 7 on the top bolts and........ ........ ........ ... 8 6 2 4 10 botton bolts and the connecting rod 45Nm or 34 lbs ft i hope be help you

Nov 09, 2009 | 1996 Honda Accord

1 Answer

What are the torque specs for installing front struts??


Damper shaft nut-------- 40 ft lbs
strut upper mounting nut--- 40 ft lbs.
strut to steering knuckle bolts/nuts---
2001 and earlier models
step 1---- 37 ft. lbs.
step 2---- 66 ft lbs.
step 3---- Tighten an additional 45 to 60 degrees
2002 and later models
step 1---- 37 ft lbs.
step 2----73 ft lbs.
step 3---- Tighten an additional 30 to 45 degrees

Nov 07, 2009 | Saturn SL2 Cars & Trucks

1 Answer

I am replacing the rear struts on my 98 toyota xls


upper nuts 36 lbs and the bottom two big ones are 145 lbs and the upper mount to body are 29 lbs. good luck man

Oct 18, 2009 | 1998 Toyota Avalon

1 Answer

How to replace a tailgate strut on a 2000 honda odyssey


you have to take th panel off and you will see how its bolt on and remove nuts and bolt accord to how they are ,,note take the top part of the stut off first

Oct 09, 2009 | 2000 Honda Odyssey

2 Answers

Front Hub Bearing Torque specs to complete replacement


THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Apr 24, 2009 | 2003 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

293 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

john h

Level 3 Expert

22486 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...