Question about 2000 Daewoo Nubira

Open Question

How to remove a water pump from a 2000 Daewoo nubria

Water pump removal

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

6ya.com

Instant Repair Help over the Phone

6ya.com

Save Time & Money by instantly connecting to...

Posted on Jan 02, 2017

Ad

Anonymous

  • 1 Answer

SOURCE: 2000 Daewoo Nubria timing mark

show me timing marks

Posted on Oct 22, 2008

Ad

Roger Foster

  • 701 Answers

SOURCE: Need Instructions on removing and replacing a fuel pump for my 2000 daewoo leganza

Hello martin09canc: First thing to do is relieve fuel pressure in the fuel system. Remove the rear seat cushion.Remove the access cover. Disconnect the electrical plug.Would not hurt to disconnect the negative battery cable. This would eliminate any sparks. Remove the sender retaining ring. Lift out the sender unit. Be careful not to spill gas on the carpet. Replace the seal and reverse the operation to install new unit. If you need further help please just ask. Please rate the quality of the answer as it also helps. Thank You for using FixYa. Roger

Posted on Apr 16, 2009

Anonymous

  • 14 Answers

SOURCE: Newly replaced timing belt was broken in my daewoo nubira 2000

Yes you should always do the water pump when doing the timing belt. belt tension too tight can cause the break as well as a bad water pump or idler pully, these should all be replaced when you do a timing belt to save yourself this exact headache later on.

Posted on May 26, 2009

Anonymous

  • 176 Answers

SOURCE: Need to remove heater core from 2000 Daewoo Nubira

  1. Disconnect the negative battery cable.
  2. Remove the instrument panel from the vehicle.
  3. Remove the heater/air distributor case from the vehicle.
  4. Disconnect the vacuum actuators from the vent/floor door and the defroster door.
  5. Remove the vacuum actuators from the heater/air distributor case.
  6. Remove the screws that secure the heater core cover to the heater/air distributor case assembly.
  7. Slowly separate the lower heater core cover from the rest of the assembly
  1. Remove the screw and the bracket clamp that secure the heater core lines to the case.
  2. Remove the spring clamp that secures the heater core body to the case.
  3. Remove the heater core from the case.
  1. Install the heater core into the case.
  2. Secure the heater core lines to the case with the retaining bracket clamp and the screw. Tighten the heater core retaining bracket screw .
  3. Install the heater core body with the retaining spring clamp.
  1. Install the heater core cover.
  2. Install and tighten the screws that secure the heater core cover to the heater/air distributor case assembly. Tighten the heater core cover screws
  3. Install the actuators for the vent/floor and the defroster doors.
  4. Install the heater/air distributor case.
  5. Install the instrument panel.
  6. Fill the cooling system
  7. Connect the negative battery cable.

Posted on Jun 18, 2009

stevenhurc

Steve Hurc

  • 459 Answers

SOURCE: how do i put the serpentine belt on a 2000 daewoo

1aa8799.jpg
here ya go

4b9f060.jpg

Posted on Sep 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change the water pump
  • Tools Required
  • J 43651 Water Pump Holding Tool
  • Remove the thermostat housing.
  • Remove the water pump access plate from the front cover.
  • Remove the right hand fender liner.
    1. Important: A drain plug has been provided at the bottom of the water pump assembly for additional coolant drainage from the engine block and water pump.
    Drain the coolant from the water pump using the plug at the bottom of the pump.
    1. mportant: The water pump holding tool supports the sprocket and chain during water pump service. The tool must be used or the balance shaft must be re-timed.
    Install the J 43651 into position.
    1. Tighten the bolts on the water pump holding tool into the threads on the water pump sprocket.
    2. Install the access cover bolts that were removed earlier to secure the water pump holding tool to the front cover assembly.
    3. Remove the 3 inner water pump sprocket to water pump blots.
      1. Important: Be sure to remove both water pump bolts from the front of the engine block.
      Remove the 2 water pump bolts.
      Remove the rear 2 water pump bolts.
      1. Remove the water pump.
      2. Remove and discard the water pump O-ring seal.
      Installation Procedure
      1. Important: Prior to installing the water pump, read the entire procedure. This will help avoid balance shaft chain re-timing and ensure proper sealing.
      Install a NEW water pump O-ring seal.

      1. Important: A guide pin can be created to aid in water pump alignment. Use a M 6 m x 6 mm stud. Thread the pin into the water pump sprocket.
      Using the guide pin, align the pin with the water pump holding tool.
      1. Position the water pump against the engine block and hand tighten the water pump bolts.
      2. Notice: Refer to Fastener Notice.
      Install the inner water pump sprocket bolts. After 2 are snug, remove the guide pin and install the 3rd bolt.
      Tighten the bolts to 25 Nm (18 ft. lbs.).
      1. Tighten the water pump sprocket bolts last. Tighten the bolts to 10 Nm (89 inch lbs.).
      2. Remove the J 43651.
      3. Install the water pump access plate and bolts. Tighten the bolts to 10 Nm (89 inch lbs.).
      4. Install the right hand fender liner.
      5. Install the thermostat housing.

Aug 29, 2011 | 2006 Pontiac Solstice

1 Answer

Need instruction for replacing water pump 2004 GMC Envoy 4.2 liter engine.
TO REPLACE WATER PUMP.FIRST YOU HAVE TO DRAIN THE COOLANT SYSTEM. REMOVE AIR INTAKE DUCT AND RESONATOR. REMOVE THE RADIATOR SHROUD AND FAN CLUTCH ASSEMBLY REMOVE THE DRIVE BELT. REMOVE WATER PUMP PULLEY.YOU NEED A PIN SPANNER WRENCH OR STRAP WRENCH TO HOLD WATER PUMP PULLEY WHILE LOOSEN WATER PUMP PULLEY BOLTS .YOU CAN BUY STRAP WRENCH OR RENT PIN SPANNER WRENCH AT AUTO ZONE PARTS STORES OR OTHER STORES HAS TOOLS CAN BE RENT. ONCE WATER PUMP PULLEY REMOVED. REMOVE THE WATER PUMP MOUNTING BOLTS. REMOVE WATER PUMP. IF WATER PUMP STUCK YOU CAN TAP WITH SOFT FACE HAMMER OR A LONG PIECE OF ROUND WOOD.WHEN WATER REMOVED.YOU NEED TO CLEAN THE SEALING SURFACE CAREFUL DONT SCRATCH SEALING SURFACE. YOU CAN BUY CAN OF SPRAY GASKET REMOVER.CLEAN SURFACE GOOD THEN WIPE WITH LACQUER THINNER OR ACETONE.THEN GET WATER PUMP NEW GASKET MATCH HOLES UP WITH GASKET TO WATER PUMP. ONCE HOLES MATCH UP APPLY RTV SEALANT ON BOTH SIDES WATER PUMP GASKET. THEN PUT GASKET ON WATER PUMP THEN INSTALL WATER PUMP TO VECHICLE.TORQUE WATER PUMP BOLTS TO 89 INCH LBS .TIGHTEN WATER PUMP PULLEY BOLTS TO 18 FT LBS THEN PUT EVERY THING BACK VISA VERSA.

Aug 26, 2011 | GMC Envoy XL Cars & Trucks

1 Answer

How long does it take to replace a water pump on Pontiac Aztec?
It takes near to 1.5 hours to replace the water pump on Pontiac Aztec. The procedure to replace the water pump is as follows:--- Water Pump Replacement ---------
Removal Procedure :
 techmecho.gif
  1. Drain the cooling system until the coolant is below the level of the water pump.
  2. Remove the drive belt guard.
  3. Loosen the water pump pulley bolts.
  4. Remove the drive belt.
techmecho_0.gif
  1. Remove the water pump pulley bolts.
  2. Remove the water pump pulley.
techmecho_1.gif
  1. Remove the water pump bolts.
  2. Remove the water pump.
  3. Remove the water pump gasket.
  4. Clean the water pump mating surfaces
Installation Procedure
  1. Install the water pump gasket.
  2. Install the water pump. Notice: Refer to Fastener Notice in Service Precautions.
  3. Install the water pump bolts.
    • Tighten the bolts to 10 Nm (89 inch lbs.) .
techmecho_2.gif
  1. Install the water pump pulley. Loosely install the mounting bolts.
  2. Install the drive belt.
  3. Install the water pump pulley bolts.
    • Tighten the bolts to 25 Nm (18 inch lbs.) .
techmecho_3.gif
  1. Install the drive belt guard.
  2. Fill the cooling system.
  3. Inspect the cooling system for leaks.
  4. That's it.

Nov 18, 2010 | 2001 Pontiac Aztek

1 Answer

How to replace water pump 2003 alero. 3400 engine.
Removal & Installation 2.2L Engine To Remove:
  1. Disconnect the battery ground cable.
  2. If equipped with an automatic transmission, remove the exhaust manifold..
  3. Drain the cooling system.
  4. Raise and safely support the vehicle.
  5. Remove or disconnect the following:
    • Right front wheel and tire assembly.
    • Right front fender liner. chevy_cav_02-04_accescover.gif

    • Access plate on the water pump sprocket from the timing cover.
  6. Install J 43651 water pump sprocket holder or equivalent to the water pump sprocket.
  7. Use the access plate bolts to attach J43651 to the engine front cover.
  8. Remove or disconnect the following:
    • Bolts that secure the sprocket to the water pump.
    • Bolt that secures the engine block to the water pump.
    • Bolt that secures the engine front cover to the water pump.
    • Feed pipe that joins the thermostat housing to the water pump. chevy_cav_02-04_wp.gif

    • 2 Bolts that secure the water pump to the engine block.
    • Water pump.
To Install:
  1. Use a threaded stud in the hub to align the water pump sprocket.
  2. Install or connect the following:
    • Water pump.
    • 2 bolts that secure the water pump to the engine block.
    • Feed pipe that joins the thermostat housing to the water pump.
    • Front cover bolt and the bolt that secures the engine block to the water pump. Tighten the bolts to 15 ft lbs (20 Nm).
    • 2 of the bolts that secure the water pump sprocket to the water pump.
  3. Remove the threaded stud.
  4. Install the last bolt.
    • Tighten the bolts to 89 in lbs (10 Nm).
  5. Remove J 43651.
  6. Install the access plate on the water pump sprocket to the timing cover.
  7. Install the access plate bolts.
    • Tighten the bolts to 18 in lbs (10 Nm).
  8. Install the front fender liner.
  9. Install the right front tire and wheel.
  10. If equipped with an automatic transmission, install the exhaust manifold.
  11. Fill the cooling system.
  12. Connect the battery ground cable.
2.4L Engine To Remove:
Water pump 2.4L 87953070.gif

  1. Disconnect the negative battery cable
  2. Drain the engine coolant.
  3. Remove the exhaust manifold.
  4. Remove the coolant intake pipe as follows:
    1. Remove the coolant inlet pipe bolts.
    2. Remove the wheel and tire assembly.
    3. Remove the engine splash shield.
    4. Remove the bolts from the transaxle-to-engine block brace and remove the brace.
    5. Remove the radiator hose from the coolant inlet pipe.
    6. Remove the coolant inlet pipe to oil pan bolt.
    7. Remove the coolant inlet pipe, thermostat and seal.
  5. Lower the vehicle.
  6. Disconnect the heater hose quick connect from the heater outlet pipe.
  7. Remove the front timing chain cover and the chain tensioner.
  8. Unfasten the water pump-to-cylinder block bolts.
  9. Remove the water pump-to-timing chain housing nuts.
  10. Remove the water pump and cover mounting bolts and nuts.
  11. Remove the water pump and cover as an assembly. Separate the two pieces after removal.
  12. Clean the mating surfaces.
To Install:
  1. Install the water pump cover to the water pump assembly.
  2. Install and hand tighten the pump cover mounting bolts.
  3. Install water pump cover assembly.
  4. Install and hand tighten the cover-to-block mounting bolts.
  5. Install and hand tighten the water pump-to-timing chain housing nuts.
    • Tighten the water pump-to-timing chain housing mounting nuts to 19 ft lb (26 Nm).
    • Tighten the water pump cover-to-water pump mounting bolts to 124 in lb (14 Nm).
    • Tighten the water pump cover-to-engine block bolts starting with the bottom bolt first to 19 ft lb (26 Nm).
  6. Install the heater hose to the water pump pipe.
  7. Using new gaskets, install the exhaust manifold.
  8. Install the oil level indicator and tube.
  9. Connect the brake vacuum tube to the cam housing.
  10. Raise and safely support the vehicle.
  11. Install the catalytic converter.
  12. Install the coolant inlet pipe.
    • Tighten the inlet pipe-to-oil pan bolt to 19 ft lb (26 Nm). Tighten the coolant inlet pipe bolt to 124 in lb (14 Nm).
  13. Install the timing chain and tensioner.
  14. Lower the vehicle.
  15. Connect the oxygen sensor.
  16. Fill cooling system and check the system for leaks.
3.4L Engine To Remove:
  1. Disconnect the battery ground cable.
  2. Drain the cooling system.
  3. Loosen the water pump pulley bolts.
  4. Remove or disconnect the following:
    • Drive belt.
    • Water pump pulley bolts and pulley.
    • Water pump bolts, pump and gasket.
    • Clean the water pump mating surfaces.
To Install:
  1. Install or connect the following:
    • Water pump gasket and pump.
    • Water pump bolts.
      1. Tighten the water pump bolts to 89 in lbs (10 Nm).
    • Water pump pulley and bolt until snug.
    • Drive belt.
  2. Tighten the water pump pulley bolts to 18 ft. lbs (25 Nm).
  3. Fill the cooling system.
  4. Check for leaks.
  5. Connect the battery ground cable.
prev.gif next.gif

Aug 31, 2010 | 2003 Oldsmobile Alero

1 Answer

How to take off the water punp
1. Drain the cooling system until the coolant is below the level of the water pump. 2. Remove the drive belt guard. 3. Loosen the water pump pulley bolts. 4. Remove the drive belt. 5. Remove the water pump pulley bolts. 6. Remove the water pump pulley. 7. Remove the water pump bolts. 8. Remove the water pump. 9. Remove the water pump gasket. 10. Clean the water pump mating surfaces. Installation Procedure 1. Install the water pump gasket. 2. Install the water pump Notice: Refer to Fastener Notice in Service Precautions. 3. Install the water pump bolts. Tighten the bolts to 10 Nm (89 inch lbs.). 4. Install the water pump pulley. 5. Install the water pump pulley bolts. 6. Install the drive belt. Tighten the water pump pulley bolts to 25 Nm (18 inch lbs.). 7. Install the drive belt guard. 8. Fill the cooling system

Aug 13, 2010 | 2002 Buick LeSabre

1 Answer

Remove and replace the water pump buick rendezvou 2003 cost and do it yourself instructions . can i do it myself concerned with loosening the serpentine belt and needing special tools?
1. Drain the cooling system until the coolant is below the level of the water pump. 2. Remove the drive belt guard. 3. Loosen the water pump pulley bolts. 4. Remove the drive belt. 5. Remove the water pump pulley bolts. 6. Remove the water pump pulley. 7. Remove the water pump bolts. 8. Remove the water pump. 9. Remove the water pump gasket. 10. Clean the water pump mating surfaces. Installation Procedure 1. Install the water pump gasket. 2. Install the water pump Notice: Refer to Fastener Notice in Service Precautions. 3. Install the water pump bolts. Tighten the bolts to 10 Nm (89 inch lbs.). 4. Install the water pump pulley. 5. Install the water pump pulley bolts. 6. Install the drive belt. Tighten the water pump pulley bolts to 25 Nm (18 inch lbs.). 7. Install the drive belt guard. 8. Fill the cooling system
Visit my Blog here

Jul 21, 2010 | 2002 Buick Rendezvous

1 Answer

Water pump removal
REMOVAL & INSTALLATION
2.0L Engine
  1. Disconnect the negative battery cable.
CAUTION Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant.
  1. Drain the engine cooling system.
  2. Raise and safely support the vehicle.
  3. Remove the lower radiator hose from the water pump.
If the lower radiator hose is hard to reach on the back of the water pump, remove the hose at the radiator and after the water pump is ready to be removed, pull the water pump away from the engine block until there is enough room to remove the hose from the pump.
  1. Lower the vehicle.
  2. Remove the accessory drive belt.
  3. Remove the timing belt covers and the timing belt as outlined in this Section.
  4. Remove the four water pump retaining bolts.
  5. Remove the water pump.
To install:
  1. Thoroughly clean all sealing surfaces.
  2. Install a new water pump gasket and the water pump onto the cylinder block.
  3. Tighten the retaining bolts to 12-15 ft. lbs. (16-20 Nm).
  4. Reinstall the timing belt and the timing belt covers as outlined in this Section.
  5. Reinstall the accessory drive belt.
  6. Raise and safely support the vehicle.
  7. Reinstall the lower radiator hose.
  8. Lower the vehicle.
  9. Fill the engine cooling system.
  10. Reconnect the negative battery cable.
  11. Start the engine and top off the coolant as necessary. Check for leaks.


2.5L Engine

Before continuing with this procedure, be sure three new water pump retaining bolts (W701544) are available. Due to their torque-to-yield design, the bolts stretch and cannot be reused.
  1. Disconnect the negative battery cable.
CAUTION Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant.
  1. Drain the engine cooling system.
  2. Remove the water pump pulley shield.
  3. Remove the water pump drive belt.
  4. Remove the water pump inlet and outlet hoses from the water pump.
  5. Remove the three water pump to left cylinder head retaining bolts.
  6. Remove the water pump and water pump housing from the vehicle.
  7. Remove the water pump to water pump housing retaining bolts and separate the water pump from the water pump housing.
To install:
  1. Thoroughly clean all sealing surfaces.
  2. Install the water pump to the water pump housing using a new gasket and install the retaining bolts. Tighten the retaining bolts to 16-18 ft. lbs. (22-25 Nm).
  3. Position the water pump and water pump housing and install three new torque-to-yield retaining bolts into the left cylinder head.
  4. Tighten the new retaining bolts to 11-13 ft. lbs. (15-18 Nm), then rotate the retaining bolts 85-95 degrees.
  5. Reinstall the water pump inlet and outlet hoses to the water pump.
  6. Reinstall the water pump drive belt.
  7. Reinstall the water pump shield.
  8. Fill the engine cooling system.
  9. Reconnect the negative battery cable.
  10. Start the engine and top off the coolant as necessary. Check for leaks.


Hope helps (remember comment and rated this).

Jul 07, 2010 | 1996 Mercury Mystique

1 Answer

How do you replace a water pump in an aztec?
Notes Water Pump Replacement

Removal Procedure
3e77de9.gif

  1. Drain the cooling system until the coolant is below the level of the water pump.
  2. Remove the drive belt guard.
  3. Loosen the water pump pulley bolts.
  4. Remove the drive belt.


c7273fb.gif
  1. Remove the water pump pulley bolts.
  2. Remove the water pump pulley.
c102468.gif
  1. Remove the water pump bolts.
  2. Remove the water pump.
  3. Remove the water pump gasket.
  4. Clean the water pump mating surfaces
Installation Procedure
  1. Install the water pump gasket.
  2. Install the water pump. Notice: Refer to Fastener Notice in Service Precautions.
  3. Install the water pump bolts.
    • Tighten the bolts to 10 Nm (89 inch lbs.) .
f16e1fd.gif
  1. Install the water pump pulley. Loosely install the mounting bolts.
  2. Install the drive belt.
  3. Install the water pump pulley bolts.
    • Tighten the bolts to 25 Nm (18 inch lbs.) .
  • 258f600.gif
  1. Install the drive belt guard.
  2. Fill the cooling system.
  3. Inspect the cooling system for leaks

Jun 17, 2009 | 2001 Pontiac Aztek

1 Answer

Water pump replace
Water Pump Replacement (3.8L)

Removal Procedure
  1. Drain the cooling system.
  2. Loosen the water pump pulley bolts.
  3. Remove the drive belt.
    1. Remove the water pump pulley bolts.
    2. Remove the water pump pulley.
    3. Remove the power steering pump and reposition.
    4. Remove the water pump bolts.
      1. Remove the water pump.
      2. Remove the water pump gasket.
      3. Clean and inspect the water pump mating surfaces.
      Installation Procedure
      1. Install the water pump gasket.
      2. Install the water pump.
        1. Notice: Refer to Fastener Notice in Service Precautions. Install the water pump bolts.
          • Tighten the long water pump bolts to 34 Nm (25 ft. lbs.) .
          • Tighten the short water pump bolts to 22 Nm (16 ft. lbs.) .
            1. Install the water pump pulley.
            2. Install the water pump pulley bolts.
              • Tighten the bolts to 13 Nm (115 inch lbs.) .
            1. Install the power steering pump.
            2. Install the drive belt.
            3. Fill the cooling system.
    5. The Whole Thing I Know You Didnt Want to hear that about The P/S Pump Thats why I Did More Reserch you seemed to Know what You are Doin They get the Best of us though Hope this Helps & RATE ME PLEASE

Feb 03, 2009 | 2005 Chevrolet Impala

1 Answer

How Do i replace Water Pump on 98 Chevy Metro
  1. Remove the negative battery cable.
  2. Drain the engine cooling system.
  3. Remove the air cleaner assembly.
  4. Remove the A/C compressor suction pipe bracket (if equipped).
  5. Loosen four water pump pulley bolts. Do not remove the bolts.
  6. Raise the vehicle. Support the vehicle. Remove the right lower splash shield.
  7. Remove the right lower splash shield.
  8. Remove the A/C compressor drive belt (if so equipped) by releasing the tensioner pulley and removing the belt from the crankshaft and compressor pulleys.
  9. Loosen the generator adjusting bolt (1), pivot the generator and remove the water pump/generator drive belt.
  10. Remove the crankshaft pulley.
  11. Remove the water pump pulley (four bolts).
  12. Remove the timing belt.
  13. Remove the oil level indicator (dipstick) guide tube.
  14. Remove the upper generator adjusting bracket from the water pump (one bolt).

    1. Remove the rubber seals from the water pump.
    2. Remove the water pump mounting bolts and nuts.
    3. Remove the water pump and gasket from the vehicle.
    4. Clean the water pump and the gasket mating surfaces.
    5. Install the water pump.
    6. Secure the water pump with mounting nuts and bolts. Tighten Tighten the water pump mounting nuts and bolts to 13 Nm (115 ft. lbs.).
    7. Install new rubber seals (1) to the water pump (2).
    8. Install the upper generator adjusting bracket to the water pump (one bolt).
        • Tighten the upper generator mounting bracket bolt to 23 Nm (17 ft. lbs.).
      1. Install the oil level indicator (dipstick) guide tube.
      2. Install the timing belt.
      3. Install the water pump pulley.
      4. Finger-tighten the four bolts.
      5. Install the crankshaft pulley.
      6. Install the water pump/generator drive belt to the crankshaft, water pump and generator pulleys.

Nov 20, 2008 | 1998 Chevrolet Metro

Not finding what you are looking for?

View Most Popular

2000 Nubira

  • Cars & Trucks

Related Question

Change the water pump

  • 2006 Pontiac Solstice

Open Questions:

0 Answers

What is the petrol consumption for Dewoo Nubira CDII?

Apr 22, 2016 | 2000 Daewoo Nubira

0 Answers

Hi the center system is working but key remote dose not working how can i reactive again or how can resolve this problem thanks Amr

Apr 06, 2015 | 2000 Daewoo Nubira

0 Answers

how do I find power windows relay windows not working

Sep 29, 2014 | 2000 Daewoo Nubira

0 Answers

why is power steering heavy?

Jul 06, 2014 | 2000 Daewoo Nubira

See all 2000 Daewoo Nubira Questions

2000 Daewoo Nubira Logo

Related Topics:

198 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

2 Answers
Replacing timing belt on daewoo nubira 2000 model

2000 Daewoo Nubira

2 Answers
The timing belt broke, need to know what are the points?

2002 Daewoo Nubira

2 Answers
My rear wiper dont work at all on my Isuzu Rodeo

Daewoo Nubira Cars & Trucks

1 Answer
Daewoo Matiz cranks but does not start

2000 Daewoo Nubira

1 Answer
Timing marks for a daewoo nubira cdx

1999 Daewoo Nubira

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

459 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...