Question about 2007 Kia K2700 Workhorse

1 Answer

Need instructions on how to change the rear brake shoes

Looking for maintenance instructions to assist with rear drum brake removal

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

  • Kia Expert
  • 27 Answers

Repair your vehicle right away. Just click on the link I attach.

Kia k2700 Workshop Service Manual

Posted on Jun 11, 2016

  • Nico Visser
    Nico Visser Aug 03, 2016

    I don't want to purchase only info

×

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 158 Answers

SOURCE: rear brake drum has been changed to some other car drum and shoe

please explain properly if you want help

?????????????????????????????????????????????????????????????????????????????????/

Posted on Apr 02, 2009

goofduck

Jeff Adkisson

  • 490 Answers

SOURCE: some pointers needed for drum brake job

the max spec is stamped on the drum you can mic them or bring them to a parts house that turns drums and rotors they can mic them for you

Posted on Apr 20, 2009

kirtec auto

  • 1348 Answers

SOURCE: how to install parking brake lever cable on new

you have to install it into the inverted shoe first,then install the shoe

Posted on Jul 17, 2009

Brandon Undeberg

  • 174 Answers

SOURCE: Need instructions to replacing rear drum brake pads. I've changed

This is usually pretty simple. Start by removing the brake drum. Sometimes the brake pads themselves prevent easy removal. There should be an adjustment hole on the back side of the backing plate. Pop the rubber plug out. Use a flat tipped screwdriver to turn the notched disc. one way will tighten and the other way will loosen it, usually both sides are different directions. Once the drum pops off you can begin replacing pads. I like to take a digital photo first, just in case... I then take each piece off one at a time and set it on the ground exactly how it went in. There is usually one big spring that holds the two shoes together, this one is tricky to release, but it's easier if you adjust that tensioner all the way in first. There will also be a couple of springs with retainers holding the pads in place. There will be a notch in the retainer, you'll have to push down and twist 90 degrees to release retainers and springs. They make a special tool, but you can use a pliers or vice grip if you're careful. Don't loose the pin or spring and retainer. Clean everything with brake cleaner and start to re-assemble.

Posted on Nov 11, 2009

snowghost1

chris wheeler

  • 784 Answers

SOURCE: cant get brake drum to

double check real quick that the E-brake is off,, also check for play in the E-brake cable, also open up the bleeder to make sure there is no pressure in the line. if all looks good then I would try and use a ' deadblow mallet ' to try and loosen the drum -- if a deadblow mallet is not availible, you can use a small 2x4 and a regular hammer ( place the 2x4 against drum body and smack the 2x4 with the hammer ).

c...

Posted on Dec 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Instructions how to replace rear drum brakes on 2001 ranger edge 4x4 4.0 eng


Dear Bryan,
Because it will take many pages of instruction here on this web-site, we would like to recommend you go to a public library or a car parts store and get a repair manual to follow the instructions.
Those repair manuals are year and model specific.
In a nutshell, here are the steps.
1) Block front wheels.
2) Jack up truck and remove rear wheels and brake drums.
3) Remove rear brake shoes, being careful to remember how you did it.
4) Install new brake shoes.
( If the rear wheel cylinders are wet, replace them.)
(Remember to retract the adjusters as the new linings are thicker than the old ones.)
5) Reinstall the drums & wheels, and lower to the ground.
God bless your efforts.

Apr 01, 2018 | Cars & Trucks

1 Answer

I have a 2005 1500 Z71 4x4 and I can't get the passanger rear brake drum off...Is there something special about getting the drum to come off? It started leaking fluid this morning and thus I have no...


the fluid is brake fluid frond the wheel cylinder...the reason why u cant get the drum off is either a rust lip on the drum or the rear brake shoes have ground into the brake drum...u need to adjust the self adjusting star wheel inward to loosen the rear shoes allowing the drum to be removed...on the back side of the drum is what is called a backing plate there will be a oval hole with a rubber plug in it remove it an use a brake spoon to de adjust the rear shoes by turning the brake spoon up ..if u dont have the oval hole u will need to cut it out of the backing plate there may be 2 oval stamps in the backing plate, cut out the one that is on the right when u r looking at the backing plate

Jul 15, 2011 | 2005 GMC Sierra

1 Answer

How do I get rear brake drum off?


You should jack up securely the rear end, and then remove the lugnuts to the wheels and remove the wheel.

Then, you may need a heavy hammer to tap on the 9 o'clock and 3 o'clock positions of the rear brake drum to loosen it up.

---
Here are instructions from Chilton/Haynes manual:

Drum Brakes Brake Drums Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Raise the vehicle.
  3. Remove or disconnect the following:
    • Rear tire and wheel assembly
    • Brake drum retaining clips (if equipped).
    • Brake drum.
NOTE: If the drum does not come off, further brake clearance can be obtained by backing off the brake automatic adjuster screw. Remove the rubber plug from the top of brake support plate. Rotate the automatic adjuster screw in an upward motion, using a screwdriver.
To Install:
  1. Install or connect the following:
    • Rear brake drum onto the hub assembly
    • Wheels
  2. Adjust the brakes as necessary
  3. Road test vehicle to check brake operation.
prev.gif next.gif

Feb 15, 2011 | 2001 Dodge Neon

1 Answer

Replace rear breaks


Rear Drum Brakes-let me know if you have rear disc brakes. Brake Drums Removal & Installation Remove the access hole plug, then back off the adjusting screw 88009g07.gif
Exploded view of the drum brake system 88009g06.gif

  1. Raise and safely support the vehicle with jackstands.
  2. Mark the relationship of the wheel to the axle flange to help maintain wheel balance after assembly.
  3. Remove the tire and wheel assembly.
  4. Mark the relationship of the brake drum to the axle flange. CAUTION
    Do not pry against the splash shield that surrounds the backing plate in an attempt to free the drum. This will bend the splash shield.
  5. If difficulty is encountered in removing the brake drum, the following steps may be of assistance.
    • Make sure the parking brake is released.
    • Back off the parking brake cable adjustment.
    • Remove the access hole plug from the backing plate.
    • Using a screwdriver, back off the adjusting screw.
    • Install the access hole plug to prevent dirt or contamination from entering the drum brake assembly.
    • Use a small amount of penetrating oil applied around the brake drum pilot hole.
    • Carefully remove the brake drum from the vehicle.
  6. After removing the brake drum it should be checked for the following:
    • Inspecting for cracks and deep grooves.
    • Inspect for out of round and taper.
    • Inspecting for hot spots (black in color).
To Install:
  1. Install the brake drum onto the vehicle aligning the reference marks on the axle flange.
  2. Install the tire and wheel assembly and hand-tighten the lug nuts.
  3. Carefully lower the vehicle, then tighten the lug nuts to 100 ft. lbs. (140 Nm).
  4. Road test the vehicle.
prev.gif next.gif

Feb 14, 2011 | 1998 Chevrolet Lumina

1 Answer

How to remove rear brake drum


Follow the instruction

Chock the front wheels and put your safety glasses on.

Loosen the rear lug nuts with the lug wrench. Jack the rear end off the ground with the floor jack and place the jack stands under the rear frame. Lower the rear end onto the jack stands.

Remove the lug nuts and wheel by hand. Put the catch pan under the brake drum and spray brake clean inside the brake drum from the rear until the drippings are clear.

Loosen the brake shoe adjuster as far as possible with the brake shoe adjuster tool, which you can pick up at your local auto parts store.

Hit the face of the brake drum with the dead blow hammer just above the center of the drum's face. Rotate the drum a quarter turn and hit it again, just above the center of the drum's face. Repeat this twice more and then try to pull the drum off. If the drum does not come off, continue to hit it, rotate it and hit it again until you can pull the drum off the hub.

Oct 16, 2010 | 2000 Ford Focus

1 Answer

Video for replacing front brakes pads and rotors on a 2004 ford e


Hello,
ccr20011001bb00.jpg Brake Bleeding
Purging air and moisture from your binders
CarCare - Maintenance - Brakes

ccr20030701as00.jpg ABS Speed Sensor Service
A clean sensor is a happy sensor
CarCare - Maintenance - Brakes

ccr20030701db00.jpg Drum Brakes - Rear Brake Drum Adjustment
It's stupid not to adjust your rear drum brakes
CarCare - Maintenance - Brakes

ccr20050201rr00.jpg Replacement Rotors
Friction, brake rotors, and you
CarCare - Maintenance - Brakes

ccr20050501pb00.jpg Power-Bleeding Brake Systems
Air today, gone tomorrow
CarCare - Maintenance - Brakes

ccr20050701bp00.jpg Replacing Brake Pads
How to replace worn pads
CarCare - Maintenance - Brakes

ccr20071101bs00.jpg Bleeding Power Steering
Getting rid of that air in there
CarCare - Maintenance - BrakesThanks

May 29, 2010 | 2004 Ford Escape

1 Answer

Remove rear brake drum 2004 Mitsubishi Outlander


Dear Brake Drum Remover,
I'm gonna tell you how to pull this drum off, ya ready?First off, get the rear of the vehicle up in the air safely, Then pull the rear tires off.After those are off then take a gander at the face of the drums, are there shiny brass looking screws installed on the face of that drum?Ifso remove those counterclockwise, then, take a hammer a shock the face off the drum firmly about three times.Now, go to the opposite side on the face of the drum and do that again, keep on doin that until you can wiggle the drum off by hand...easy as that, any other questions get back to me. I'M HERE TO HELP!!!

Nov 21, 2009 | 2003 Mitsubishi Galant

1 Answer

How does the rear brake drum come off of a 96 nissan pickup?


Removing the rear brake drums vary little from one vehicle to the next.First,loosen the lugs on the rear wheels,release the hand brake, block the front wheels,jack up the rear and use jackstands.Then remove the rear wheels.Looking at the drum after the wheels have been removed, you will notice two threaded holes one on each side of the axle flange.Give the brake drum a smart rap or two with a plastic mallet or piece of wood and spray the flange w/ WD 40 or brake parts cleaner.Obtain a bolt with the exact size and thread to fit the hole. I found it useful to "borrow" such bolt from around the work area-My favorite is the one fastening a cable or a hoseclamp to the differential.If that don't fit, look around under the hood:there's one there you can use.Thread the bolt into the hole alternating from one hole to the other.The bolt pushes the drum against a flange inside and removes the drum.After work, adjust the star wheel brake adjuster so that the drum turns with hand push with a little drag.

Oct 17, 2009 | 1996 Nissan Pickup

1 Answer

1999 nissan quest rear brake shoes need changing


help is here:
http://autos.groups.yahoo.com/group/villagerquest/

Drum Removal
  1. Remove the rear wheel and the tire assembly. Refer to Section 204-04 .
  1. Retract the brake shoes and loosen the brake adjuster screw.
975565f.gif
  1. Remove the brake drum.
----------------------
May require big hammer to loosen drum from axle flange. Hit between the the lugs, not on them.

------------------------------------------------------------------------------
#10 is access plug to back off adjusting wheel.

f9f31b5.gif
Item Part Number Description 1 2261 Rear wheel cylinder 2 — Dust boot (part of 2128) 3 2197 Wheel cylinder piston (part of 2261) 4 — Cup (part of 2128) 5 2204 Wheel cylinder piston cup spring (part of 2128) 6 — Wheel cylinder housing (part of 2261) 7 — Brake shoe hold-down pin 8 — Access hole (part of 2212) 9 — Rear brake bleeder screw (part of 2261) 10 — Access hole plug 11 — Rear wheel cylinder bolt 12 2212 Rear brake backing plate 13 — Rear brake backing plate bolts 14 2N790 Parking brake lever clip 15 — Spring washer 16 — Secondary brake shoe and lining (part of 2200) 17 — Brake shoe hold-down spring (part of 2B514) 18 — Lower retracting spring (part of 2B514) 19 2A637 Parking brake lever 20 — Parking brake lever pin 21 2A177 Brake shoe adjusting lever 22 — Adjuster lever pin (part of 2A177) 23 — Primary brake shoe and lining (part of 2200) 24 — Upper retracting spring (part of 2B514) 25 2041 Brake adjuster screw

--------------
Shoes Removal

Take a picture and remember how each part goes and attaches
  1. Remove the brake drum, refer to Drum in this section.
  1. Remove the upper retracting spring.
  1. Remove the lower retracting spring.
  1. Remove the self-adjuster.
38bcaa0.gif
  1. Remove the hold-down springs.
  1. Remove the parking brake lever clip and the parking brake lever.

Apr 17, 2009 | 1999 Nissan Quest

1 Answer

Bent right rear RH axle 2001 prerunner 2wd.


Hello, and welcome to FixYa. Let me assist you as follows:
Removing the rear axle shaft is realy quite easy.
Her is what you need to do:

Remove the wheel/tire.
Remove the rear brake drum.
Remove the brake line to the rear wheel cylinder and plug the line.
Remove the park brake cable.
Remove the entire rear backing plate assembly; no need to remove the rear shoes.
When the backing plate is off, the axle shaft slides out of the axle housing; there are no "C" clips to remove, like on a Chevrolet. The axle is not held at the differential in any fashion.
Note that if you replace the axle shaft, you will need a machine shop to press the wheel bearings & seals onto the new shaft.

If you have any further questions; please feel free to respond.

Thanks for choosing FixYa for assistance; the graciousness of a FixYa rating for my instructions would be greatly appreciated.
Thanks in advance.

Jan 25, 2009 | 2001 Toyota Tacoma

Not finding what you are looking for?
2007 Kia K2700 Workhorse Logo

Related Topics:

441 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...