Question about Cars & Trucks

1 Answer

I have a 2006 ford fusion which the radio system

I have a 2006 ford fusion which the radio system has went out completely. I believe it might be a fuse blown but in order for me to change the fuse I need to know which fuse is connected to the radio? My car didnt come with a manual so I have no idea which fuse to change Can you please help?

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 15,575 Answers

Inspection and Verification

  1. Verify the customer concern.
  1. Visually inspect the following for obvious signs of mechanical or electrical damage.


Visual Inspection Chart Mechanical Electrical
  • Audio unit
  • Antenna
  • Antenna cable
  • Door trim panel(s)
  • Speaker(s)
  • Noise suppression equipment
  • Smart junction box (SJB) fuse(s):
    • 12 (7.5A) (accessory delay feed)
    • 17 (20A) (subwoofer amplifier) (Audiophile)
    • 18 (20A) (audio unit hot at all times)
    • 22 (7.5A) (audio unit hot in START)
  • Battery junction box (BJB) fuse(s):
    • 20 (20A) (LH audio amplifier) (THX®)
    • 21 (20A) (RH audio amplifier) (THX®)
  • Circuitry
  • Digital signal processing (DSP) module (THX®)
  • Subwoofer amplifier (Audiophile)
  • Audio amplifier(s) (THX®)
  • Audio unit

  1. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
  1. If the cause is not visually evident, connect the diagnostic tool to the data link connector (DLC) and select the vehicle to be tested from the diagnostic tool menu. If the diagnostic tool does not communicate with the vehicle:
    • check that the program card is correctly installed.
    • check the connections to the vehicle.
    • check the ignition switch position.
  1. If the diagnostic tool still does not communicate with the vehicle, refer to the diagnostic tool operating manual.
  1. Carry out the diagnostic tool data link test. If the diagnostic tool responds with:
    • CAN circuit fault; all electronic control units no response/not equipped, refer to Section 418-00 .
    • No response/not equipped for the audio unit, Go To Pinpoint Test A .
    • NOTE: Do not press any buttons on the audio unit while the audio unit is carrying out the self-test. System passed, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs, and carry out self-test diagnostics for the audio unit.
  1. If the DTCs retrieved are related to the concern, go to Audio Unit Diagnostic Trouble Code (DTC) Index.
  1. If no DTCs related to the concern are retrieved, and the concern is not visually evident, proceed to the Speaker Walk-Around Test and the Audio Unit Self-Diagnostic Mode.

Audio Unit Self-Diagnostic Mode
NOTE: To enter the audio unit self-diagnostic mode, the audio unit must be turned on and in radio tuner mode (AM/FM).
  1. To enter the following tests, press the desired preset button while in the speaker walk-around test or while in the audio unit self-diagnostic mode.
  1. To exit the audio unit self-diagnostic mode, turn the key OFF or the audio unit off.
  1. If the concern remains and the fault is not detected, GO to Symptom Chart to continue diagnostics.
  1. The self-diagnostic mode has the following functions available:
    • Preset button 1 = On-Demand Self-Test. This button runs the on-demand self-test.
      • Pressing the MENU DOWN button allows scrolling of any DTCs found during the test while in this menu.
    • Preset button 2 = Display Continuous DTCs. This button enables viewing of any continuous DTCs that have been logged.
      • Pressing the MENU UP button allows scrolling of any DTCs while in this menu.
      • While continuous DTCs are being displayed, pressing the EJECT button will clear all present DTCs.
    • Preset button 3 = Signal Strength Test. This button displays the signal strength.
    • Preset button 4 = Software Version Display. This button displays the audio unit software version.
      • Pressing the MENU UP button allows scrolling of all audio subsystem software versions while in this menu.
    • Preset button 5 = Display Test. This test illuminates all the display segments for 5 seconds, then turns all segments off.
    • Preset button 6 = Configuration Status. This button enables audio unit configuration status.
      • Pressing the MENU button displays the ACM part number while in this menu.
  1. To exit the self-diagnostic mode, turn the audio unit off or turn the key OFF.
  1. If the concern remains and the fault is not detected, GO to Symptom Chart to continue diagnostics.

Posted on Feb 05, 2018

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
richie9911

Richard M.

  • 155 Answers

SOURCE: Can't find fuse for Ford Fusion radio.

There are 3 fuses that go to the radio. They all located in the fuse panel under the left hand side of the dash. Fuse #22 7.5 amp, fuse#18 20 amp and fuse#12 7.5 amp.

Posted on Dec 06, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 ford fusion dome light


bulb is prablly blown if they are good then there is a fuse for it

Jan 14, 2013 | 2006 Ford Fusion

1 Answer

Can't find fuse for Ford Fusion radio.


There are 3 fuses that go to the radio. They all located in the fuse panel under the left hand side of the dash. Fuse #22 7.5 amp, fuse#18 20 amp and fuse#12 7.5 amp.

Dec 06, 2012 | 2009 Ford Fusion

2 Answers

My battery went dead on my ford fusion 2008 now my radio doesn't work


As with many newr cars, Your radio probably had a security code which is required to reset it after the radio is removed or power was disconnected from it. You probably have the code written somewhere in your new car paperwork. If not, contact your dealer. They can probably guide you through resetting the code.

Nov 03, 2010 | 2006 Ford Fusion

2 Answers

Ford fusion 2007, blown blower fuse, replaced fuse, works at highest speed only (highest of 4) the other three setings don't work.


hte blower resistor is shot, near the blower motor, have the blower motor checked my guess is that it requiring too much power to run, hence the blown fuse

May 06, 2010 | 2006 Ford Fusion

1 Answer

WHICH IS THE RELAY FOR A 06 FORD FUSION FOR THE HORN


Yur car's horns have no relay just a 20 amp fuse.
Fuse #2 20Amp Horns

Apr 03, 2009 | 2006 Ford Fusion

2 Answers

2006 ford fusion i cant find the cig lighter fuse


The fuse for the cigarette light is fuse number 15 in the fuse box inside the vehicle. The fuse will be a 20 amp fuse. The fuse panel will be under the dash on the driver side. This will have a cover over it and may take a flashlight to find. Replace the fuse and test to see if its working. If its not check the fuse again. If you find it blown again look for loose change or some conductor stuck in the cigarette lighter. good luck

Jan 06, 2009 | 2006 Ford Fusion

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

john h

Level 3 Expert

22486 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...