Question about 2007 Kia Rondo LX V6

1 Answer

What is the torque specs on the intake manifold to surge tank

I did a spark plug change and removed the intake manifold. I need to torque specs. on the throttle body and intake manifold. I really dont want to get a vaccuum leak.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Kia Master
  • 635 Answers

They are in the factory repair manual.

Posted on Feb 03, 2017

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 40 Answers

SOURCE: 2002 kia sedona spark plug change

Correct, its called the Plenum.... And it has to be removed.. you can loosen MOST of the things hooked to it, such as electrical plugs and EGR valve,ect and then "flop" it over out of the way.. you will need a new gasket for it before reinstalling it..
Sounds complicated, but it isnt...

Posted on Nov 07, 2008

aref_bilal

Aref Bilal

  • 13 Answers

SOURCE: I am changing the spark plugs on my 2004 Kia sorento

Be careful there.. If you remove the Throttle Position Sensor TPS or the throttle Cable, the engine light will come on because there is a certain setting that needs to be done to ensure accurate emission control.

Posted on Apr 14, 2009

Anonymous

  • 1 Answer

SOURCE: how do you change the spark plugs on a kia optima 2.7 v6

you have to remve the bolts on top and sides of the plenum assy be sure not to drop anything down in the lower intake!!!!! the bolt heads are 12mm and there are 2 on top 2 on the ends and three int the front

Posted on Apr 16, 2009

Boat Chief

  • 8 Answers

SOURCE: Need a picture of how to take the intake manifold

go to: http://www.centuryperformance.com/forum/showthread.php?p=36

Posted on Jul 18, 2010

jesse nelson

  • 170 Answers

SOURCE: torque spec optima 2.4L

unimportant.
use 1 hand and just snug it up. not real tight , just a little pressure past the stop.
i never seen a spark plug wiggle loose, since the spark plug wire doesn't allow it to spin

Posted on Jul 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Intake manifold torque specs 2000 olds silhoutte 3.4


Follow the link for a complete listing of this engines bolt torque specs. Torque Specs Database

Jan 25, 2017 | 2000 Oldsmobile Silhouette

1 Answer

Wgolf.mk4.reg2000.removing upper part inlet manifold.


If you have a 2000 VW Golf 2.0 liter, the answer is yes. Just remove the top part of the intake manifold. A magnet and long handle allen key set will make the job easier for removing/ reinstalling the cap screws. Once manifold off, cover the intake holes with blue painters tape, to avoid dropping any thing down in them. Take care on plug wire removal. Change each plug one at a time. ***Tighten spark plugs with a torque wrench, spec 22 ft-lb in the Bentley manual. AEG, AVH, AZG eng codes***

Jul 08, 2014 | 2000 Volkswagen Golf

1 Answer

What are the torque specs on a 2002 toyota sienna's spark plugs, air intake manifold, and valve covers? Thank you.


Spark plug torque on the 3.0L engine is 13 ft.lbs. and the 3.3L is 18 ft.lbs.

Valve covers-69 inch lbs.

Intake Manifold-11 ft. lbs.

Jul 07, 2014 | 2002 Toyota Sienna

1 Answer

How to replace spark plugs on bentley continental gt 2005


you have to pull the intake off of the top of the engine. and then pull each coil pack with a special tool, and then remove the sparkplugs all 12 of them. then you will have to torque to proper spec. and reinstall the coil packs( there was a recall for certain coil replacement for causing a fire). and then put a new gasket on for the intake and then install the intake to proper specs.
hope helps...

Nov 08, 2012 | 2003 Bentley Continental GT

1 Answer

I need instructions and specs on changing a starter on a 94 seville


The starter on the Northstar engine is nestled in intake valley underneath the intake manifold. You must first disconnect the negative battery terminal and then relieve the fuel pressure. After you will have to remove the intake assembly to get at the starter which then after that its pretty basic to remove the starter.
Just be sure to torque the bolts on the intake back to spec when reassembling (torque specs are written on the intake manifold in bold yellow lettering from what I can recall).
With these complicated cars you are better off joining a site like caddyinfo.com and reading their how-to forums and asking other Cadillac owners for advice. It`s very easy when you know what you`re confident and have some simple mechanical ``know-how

Jul 16, 2012 | Cars & Trucks

1 Answer

Could you advise what are the cylinder head bolt tension settings for hyundai lantra j5. Could you email me back on judy.ben@optusnet.com.au. Thanks


let me see if i can get some info 4 you.

edit
REMOVAL

1. Drain the coolant and disconnect the upper radiator hose.
2. Remove the breather hose (between the air cleaner and the head cover).
3. Remove the air-intake hose.
4. Remove the vacuum hose, fuel hose and coolant hose.
5. Remove the cables from the spark plugs. The cables should be removed by holding the boot portion.
6. Remove the ignition coil.
7. Remove the power steering oil pump and bracket.
8. Remove the intake manifold.
9. Remove the heat protector and exhaust manifold assembly.
10. Remove the coolant pump pulley and the crankshaft pulley.
11. Remove the timing belt cover.
12. Remove the timing belt tensioner pulley.
13. Remove the timing belt.
14. Remove the head cover.


15. Remove the cylinder head assembly. The cylinder head bolts should be removed by using Special Tool, Cylinder Head Bolt Wrench (09221-32001) or equivalent, in the sequence as shown in the illustration in two or three steps.
16. Remove the gasket pieces from the cylinder block top surface and cylinder head bottom surface. NOTE: Make sure that the gasket pieces do not fall in the engine.

INSTALLATION

1. Clean all gasket surfaces of the cylinder block and the cylinder head.
2. Install a new cylinder head gasket onto the cylinder head assembly. Apply sealant to the gasket and do not reuse the old cylinder head gasket.


3. Install the cylinder head bolts. Starting at top center, tighten all cylinder head bolts in sequence as shown in illustration, using the Cylinder Head Bolt Wrench (09221 - 32001) or equivalent. Repeat the procedure, re-tightening all cylinder head bolt to the specified torque. (torque spec is Cold Engine 105-115 Nm (76-83 ft lb) )
4. Install the timing belt tensioner pulley.
5. Install the timing belt on the camshaft sprocket, making sure that the tension side is tightened by turning the camshaft sprocket in reverse, all timing marks are in alignment.
6. Adjust the timing according to "Timing Belt"
7. Install the rocker cover and tighten the bolts to the specified torque. Tightening torque: Rocker cover belt:

2.5-3.5 Nm (25-35 kg.cm, 2-3 ft. lbs.)

8. Install the timing belt cover.
9. Install the new intake manifold gasket and the intake manifold. Tighten the nuts and bolts to the specified torque.
10. Install the new exhaust manifold gasket and the exhaust manifold. Tighten the exhaust manifold attaching nuts to the specified torque.
11. Install the surge tank and tighten the nuts bolts to the specified torque.
12. Install the power steering oil pump and bracket.
13. Install the ignition coil.
14. Install the air intake hose.
15. Connect the vacuum hose, fuel hose and water hose.
16. Install breather hose.

Jun 08, 2011 | Hyundai Elantra Cars & Trucks

1 Answer

Need cylinder head torque specifications 2004 hyundai elantra


Install the cylinder head bolts. Starting at top center, tighten all cylinder head bolts in sequence as shown in illustration, using the Cylinder Head Bolt Wrench (09221 - 32001) or equivalent. Repeat the procedure, re-tightening all cylinder head bolt to the specified torque. (torque spec is Cold Engine 105-115 Nm (76-83 ft lb) )
. Install the timing belt tensioner pulley.
. Install the timing belt on the camshaft sprocket, making sure that the tension side is tightened by turning the camshaft sprocket in reverse, all timing marks are in alignment.
. Adjust the timing according to "Timing Belt"
. Install the rocker cover and tighten the bolts to the specified torque. Tightening torque: Rocker cover belt:

2.5-3.5 Nm (25-35 kg.cm, 2-3 ft. lbs.)

. Install the timing belt cover.
Install the new intake manifold gasket and the intake manifold. Tighten the nuts and bolts to the specified torque.
Install the new exhaust manifold gasket and the exhaust manifold. Tighten the exhaust manifold attaching nuts to the specified torque.
. Install the surge tank and tighten the nuts bolts to the specified torque.
. Install the power steering oil pump and bracket.
. Install the ignition coil.
. Install the air intake hose.
Connect the vacuum hose, fuel hose and water hose.
. Install breather hose.

Dec 22, 2010 | 2004 Hyundai Elantra

1 Answer

2004 Hyundai Sonata 6 cyl


Depends on how MECHANICALLY INCLINED you are. Have you done any repair work on vehicle engines before? It's not that difficult to do if you know how to turn a wrench/ratchet and THINK about what you are doing and what you are dealing with... .attention to details. Ya think? On the 04 2.7 lit V6 Sonata, there are two nuts and 5 bolts (two long and three short) which hold the plenum to the RISER manifold. There are an additional 3 to 4 bolts at the rear (firewall side) which support the plenum (they're all 12mm bolts). You'll need to remove the intake air hose to lift the plenum out of the way to access the 3 plugs on the RH side (rear) of the engine. You'll want to replace the plenum gasket when you do this. When you reinstall the plenum, the tightening torque is 11-14 lb.ft. Do not tighten the REAR support bolts until after you torque the surge tank bolts to the intake (riser) manifold.
ab1cefd.jpg

Jun 13, 2009 | Hyundai Motor 2004 Sonata

Not finding what you are looking for?
2007 Kia Rondo LX V6 Logo

Related Topics:

654 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...