Question about 1998 Toyota Avalon

Open Question

How to replace the Emergency brake cable - 1998 Toyota Avalon

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i get brake to release


The wheel that is seized with the brake should be identified, and the car should be securely supported on a jack. The seized wheel should be removed so that the brake is visible. Gently tapping the brake with a hammer helps remove any adhesions. The cable may need to be replaced because the parking brake can become stuck due to a faulty cable or faulty calipers. The cable can rust and wear down over time.
The symptoms of a faulty emergency brake include a very heavy brake pedal, a burning smell from the front tires, and dark, dirty brake fluid. Replacing the brake fluid can also help keep the emergency brake lubricated. After going through below-freezing temperatures, the cable can freeze and remain in place even when the emergency brake handle is lowered.

Dec 28, 2016 | Cars & Trucks

1 Answer

How too release the emergency brake foot pedal when the cable is broken?


About 73,400 results (0.87 seconds) Search Results

    Parking brake release cable snaps - Chevy Avalanche Fan Club of ...

    chevyavalanchefanclub.com > ... > Problems: Brakes

    24 posts - ‎16 authors
    Went to release the parking brake on my 04 and the cable snapped. ... More like the end cap coming of the cable that attaches to the foot pedal. ..... Then I released the parking brake, pulled out the broken release cable/handle assembly, ...

    How To Install Repair Replace Parking Brake Release ...

    ? 5:54
    https://www.youtube.com/watch?v=qx0oGfV62NQ
    Jun 23, 2011 - Uploaded by 1A Auto Parts
    How To Install Repair Replace Parking Brake Release CableHandle ... or replace a broken or worn out parking brake release cable handle.

    Emergency Brake Pedal Assembly & Stuck Brake Cable ...

    ? 10:13
    https://www.youtube.com/watch?v=0jYfvthBzhU
    Apr 17, 2014 - Uploaded by corgLLC
    Emergency (Parking) Brake Pedal Assembly & Stuck Emergency (Parking) Rear Brake Cable The emergency ...

    E-Brake Cable Broken? Stuck Emergency Brake... Help Please ' Chevy ...

    www.tahoeyukonforum.com > ... > Engine & Drivetrain


Jan 25, 2016 | Cars & Trucks

1 Answer

Emergency brake cable installation


Purchase a Haynes repair manual for your vehicle. It should have step by step instructions with pictures showing how to replace a park brake cable.

Good luck, I hope this helps!

Apr 17, 2014 | 1995 Ford Econoline

1 Answer

Replacing caliper on 1997 sable, how do I disconnect emergency brake line from caliper?


The cables usually use a groove and hook system where the Emergency brake cables slide into the hook of the fixture on the Caliper. The assembly must be turned almost 90 degrees to slip the fixture into and out of the channel.

Jun 07, 2012 | 1997 Mercury Sable

1 Answer

Brake realese cable broke from inside vehicle how do i unlock the emergency brakes


You will need to get underneath the vehicle and loosen the emergency brake adjuster to relieve the tension on the cables. Bear in mind that untill you replace the broken cable and readjust the emergency brake, you will have no emergency brakes.

Jun 23, 2011 | 1996 Dodge Caravan

2 Answers

Emergency brake light stays on the dash. is it a troubleshooting light?


It probably indicates that the cable is not being fully retracted when brake is disengaged. Spray as much of cable as possible with WD-40, allow to sit for a few hours, the engage and disengage the brake several times untill it loosens. If this fails the cable may be stretched and needs to be replaced.

Jun 25, 2010 | 1996 GMC Yukon

1 Answer

Emergency brake stuck, pedal release broken


What happens is the brake cables rust inside the cable sheath and then they won't slide easily. There's no good fix for this other than replacement. It's not easy to even find where they are stuck.It might be possible to find the end of the cables at the back wheels and pull the cables back---to release the tension

Apr 26, 2009 | 1994 Pontiac Grand Prix

1 Answer

Emergency brake LOCKED UP on my 97 ranger


The right emergency brake cable is probaly chafed through somewhere.Try wiggling the cable around and see if it backs off.More than likely you need to get the cable replaced.

Feb 21, 2009 | 1997 Ford Ranger SuperCab

1 Answer

Emergency brake not holdind


either need to adjust the emergency brake cable or replace your rear pads

Oct 25, 2008 | 2001 Hyundai Accent

1 Answer

Parking or emergency Brake problem


Check the hardware for the drum emergency brake inside the the rear disc brakes, these pads are for your emergency brake, there should be an adjustment bolt that just sits between the two pads. Also, check the cables running to this set of pads to make sure they were connected properly. After you have checked the drum emergency brake, follow the cables in the undercarriage and look for the point at which they combine to another single cable, this is the point where the actual cable pressure adjustment is located.

Aug 07, 2008 | GMC Jimmy Cars & Trucks

Not finding what you are looking for?
1998 Toyota Avalon Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...