Question about Cars & Trucks

1 Answer

Replacing alternator belt on 2007 1.3 cdti combo is it easy to do

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Passionate:

    Visited the website for 10 consecutive days.

  • Expert
  • 160 Answers

Loosen alternator, push it towards the block until belt is loose. Pull the belt off and replace. Once the new belt is on push the alternator away from the block until belt is tight and tighten bolt/bolts. You might need a bar to keep tension on the alternator while tightening bolt/bolts.

Posted on Oct 20, 2016

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace the alternator in a 2007 jeep compass limited


First..,Get new part and also a new belt if belt has never been changed..Make sure part is correct,Use safety glasses..Be sure engine is cold..,Notice sticker under hood that shows belt routing diagram..If there isn't a sticker you can hand draw your own..Disconnect battery ground cable..Remove serpentine belt..If you have never replaced a serpentine belt it will get you confused but it is VERY EASY..It should have a diagram of how it is removed on the sticker showing the belt..The salesman at the parts store can show you easier than I can tell you..After removing belt ..,inspect all pulleys for tightness or any type of wobble..Look for any small shines of metal fragments around pulleys..Spin pulleys to make sure they don't have a worn bearing noise and they spin freely......If one seems damaged now is the time to replace it...remove wiring from alternator carefully..Remove alternator mounting bolts..Use a small pry bar or large flat screwdriver to pry the alternator carefully at both sides upward to remove it..It has a small bushing inside of the lower mounting holes which slides in and out to help keep alternator in position.The old alternator is to be turned in to parts store for a core credit so try not to damage it....Lube mounting holes of new alternator so it will slide into place smoothly..Install bolts and get them all hand tight then snug each bolt lightly until they are all seated then torque each bolt..Torque tight but DONT OVER TIGHTEN..It should be no more than 40lbs.torque..carefully connect alternator wiring..Install new belt..Doublecheck everything..,remove all tools from under hood..Coonect battery and start engine for safety check...

Feb 22, 2015 | 2007 Jeep Compass Limited

1 Answer

Remove alternator


If you know where the alternator is then this is a pretty easy thing to replace. You will have to remove the serpentine belt which is held tight by the idler. You can release the tension on that with one bolt. Once that is loosened then you can remove the alternator which in most cases is three bolts. Once those are out you can manipulate it out for replacement. Disconnect the battery before you start.

Sep 04, 2014 | 2007 Hyundai Santa Fe

1 Answer

2007 volvo S40 will not start after replacing alternator belt, smell gas after trying to start


I am thinking faulty injectors and/or excessive fuel pressure in the fuel manifold . Run fault codes again ensuring that the cables used and the procedure to connect is adhered to as there will be a fault code recorded but not being read

Mar 22, 2014 | 2007 Volvo S40 2.4i Sedan

1 Answer

CAN'T GET ANY GEARS VAUXHALL COMBO 1.7 CDTI


Well first, is it auto or manual? The answers are different depending.

Jan 15, 2014 | 2003 Pontiac Sunfire

1 Answer

How do you get the serpetine belt back on?


if u have the diagram the rest is easy .you will need a racket or a loaner tool from auto zone put the racket n the tensioner hole a small square hole that wil move back and forth with some force

Jul 12, 2009 | 2007 GMC Yukon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

john h

Level 3 Expert

22486 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...