Question about 2001 Ford Explorer Sport Trac
This happened suddenly. Trying to somehow diagnose what the issue(s) could be. Drives perfect in 2WD. No clunking noise when shifting to 4WD - nothing at all (no light comes on either)
Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Good luck!
Posted on Jan 02, 2017
SOURCE: pcv valve :where is it located on a 1999 ford explorer sport 2wd
It is located at the back of the engine near the fire wall. It is gray with a T connector at the top with two hoses coming off of the T and going forward into the intake manifold.
Posted on Mar 07, 2009
SOURCE: 2007 FORD EXPLORER SPORT TRAC 4X4 Change oil light on
Press and hold the SELECT/RESET
control switch to select SYSTEM
CHECK when “SYSTEM CHECK /
HOLD RESET” is displayed in the
message center. Selecting this
function from the SETUP MENU
causes the message center to cycle through each of the systems being
monitored. For each of the monitored systems, the message center will
indicate either an OK message or a warning message for two seconds.
Pressing the SELECT/RESET control switch cycles the message center
through each of the systems being monitored.
The sequence of the system check report and how it appears in the
message center is as follows:
1. OIL LIFE RESET
2. CHARGING SYSTEM
3. WASHER FLUID
4. DOOR AJAR
5. EXTERIOR LAMP
6. BRAKE SYSTEM
7. PARK BRAKE
8. MILES TO EMPTY
9. FUEL LEVEL LOW (will only display if 50 miles or less to empty)
To reset the oil monitoring system to 100% after each oil change
[approximately 5,000 miles (8,000 km) or 180 days] perform the
following:
1. Enter SYSTEM CHECK to display
“OIL XXX% RESET IF NEW”.
2. Press SELECT/RESET control
switch to display “HOLD RESET IF
NEW OIL”.
3. Press and hold the
SELECT/RESET control switch for
more than 2 seconds. Oil life is set
to 100% and “OIL CHANGE SET TO
100%” is displayed.
Posted on Apr 02, 2009
SOURCE: how to change fuel filter on 2001 ford explorer
it in the tank so your gonna either gonna have to drain the tank and lower it to the ground,it shouldn't take more than 30 minutes.make sure you put the seal back in right,so it won't leak,it aint very hard.
Posted on Jul 12, 2009
SOURCE: where is the resistor in a 2001 ford explorer
You have to remove your glove box and it is behind there. Here is a picture of where it is. This particular picture is from a 4 X 4 so if you don't have that it won't have the 4X4 part. Let me know if you have any more questions. Thanks for using FixYa!
Posted on Jul 15, 2009
SOURCE: where is the fuel filter location on a 2001 ford
It is inside the left frame rail below the drivers door, you need a special tool to release the filter from the line. filter just snaps into its metal holder. Good luck and you can get the fuel line quick release tool at most Auto Parts store.
Posted on Mar 06, 2010
Mar 09, 2018 | Ford Cars & Trucks
Jan 10, 2016 | 2001 Ford Explorer Sport
Nov 18, 2014 | 2001 Ford Explorer Sport Trac
Nov 13, 2013 | 2001 Ford Explorer Sport Trac
Jan 28, 2013 | 2004 Ford Explorer Sport Trac
Jul 04, 2012 | 2001 Ford Explorer Sport Trac
Oct 03, 2010 | 2001 Ford Explorer Sport Trac
Jul 26, 2010 | 2001 Ford Explorer Sport Trac
Jun 22, 2010 | 2001 Ford Explorer Sport Trac
Jan 12, 2010 | 2001 Ford Explorer Sport Trac
102 people viewed this question
Usually answered in minutes!
×