Question about 2009 Chevrolet HHR

Open Question

I have a 2009 HHR with a broken radio mast. Since the mast has broken, I am having speaker issues. What size replacement mast do I need and can it be a screw-in?

Posted by on

Ad

5 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
shannongreer

Shannon Greer

  • 75 Answers

SOURCE: Antenna mast broken

    Give these instructions a shot. Might be too generic but might be enough to get you going. Removing Original Antenna
  1. Step 1 Activate the antenna switch to the up position.
  2. Step 2 Using the wrench or needle-nose pliers, loosen and remove the original retaining nut on the base of the antenna mast.
  3. Step 3 Gain access to the underside of the area where the antenna is located.
  4. Step 4 Remove the bracket or brace that is below the hole and holding the antenna in place.
  5. Step 5 Remove the mast.
  6. Step 6 Find the motor that controls the antenna mast. Generally, power antennas will have a constant 12-volt lead and a ground lead. The ground lead will be grounded to the panel next to the motor.
  7. Step 7 Remove the ground lead from the panel.
  8. Step 8 Pull out the antenna coaxial cable.
  9. Step 9 Unplug the coaxial from the extension coaxial cable.
  10. Step 10 Remove the original antenna coaxial cable. Note the route the cable follows.
    Installing the New Power Antenna
  11. Step 1 Inspect the fender area where the antenna mast will be mounted for rust.
  12. Step 2 Clean the area before installing the new antenna.
  13. Step 3 Plug the new antenna coaxial cable to the extension coaxial cable. (On some General Motors and Ford cars you may need an adapter to mate the 2 cables together. Car audio retail stores sell such an adapter.)
  14. Step 4 Plug the new antenna's coaxial cable into the radio's chassis antenna jack if there is no extension coaxial cable. Tie or tape the string you put on the extension cable to the new antenna coaxial cable. This assures that the 2 cables stay together as you route them to the antenna mount in the fender.
  15. Step 5 Connect the power lead of the antenna to the power antenna lead on the radio.
  16. Step 6 Connect the 12-volt constant lead to the antenna to a 12-volt source or to the ignition switch.
  17. Step 7 Direct the new antenna cable via the same route followed by the original antenna cable on up to the hole in the fender in which the mast will be mounted.
  18. Step 8 Ground the ground lead from the motor to a clean metal surface on the metal panel near the mount.
  19. Step 9 Insert the mast into the hole. Face the serrated side of the plastic cable on the bottom of the mast toward the motor side. The plastic cable can be inserted freely to about 12 inches and will stop.
  20. Step 10 Turn on antenna switch to down position until the plastic cable goes down and catches into the gear mechanism of the drum housing. If the plastic cable does not gear into the mechanism, twist the cable slightly until the cable contacts into the gear mechanism while the motor is in operation.
  21. Step 11 Stop the motor after the cable goes into the housing 12 to 25 inches.
  22. Step 12 Secure the bracket or strap to the bottom of the antenna mast and to the metal fender.
  23. Step 13 Replace the retainer nut to the base of the antenna mast and secure tightly.
  24. Step 14 Replace the panel that covers the antenna mount area.

Posted on May 13, 2009

Ad

Anonymous

  • 11 Answers

SOURCE: 1980 corvette with broken mast on a power antanna

i do not know

Posted on Sep 09, 2009

dannuest

Dan Nuest

  • 31 Answers

SOURCE: replace heater core on 2009 chevy hhr-how

get on youtube, and you will find the info that you need most of the time. you may need to remove the entire dash, to access this unit. so, be very sure what you are doing, before you tackle this job.

Posted on Nov 20, 2011

jroscar1027

  • 19 Answers

SOURCE: Looking for help on how to unlock a radio in a 2009 Chevy HHR?

Call the dealer and tell them about the radio lock problem. They'll ask for your con number and give you the unlock code.

Posted on Mar 01, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tacoma(1997) power antenna mast with broken cord will not come out after the chrome nut is removed. Any suggestions? Antenna motor still works.


Power Antenna Mast Replacement 97 fjz-80 ' IH8MUD Forum

forum.ih8mud.com > Forums > Toyota Tech Forums > 80-Series Tech
Oct 1, 2010 - I'm looking for a "how to" on replacing the OEM power mast on a 97 LC. ... The only tricky part is removing the funky nut that holds the mast in. .... what to do with the radio mast on my newly acquired 1997 Lexus LX450. ... if I have a broken cable, but the antenna itself comes right out of the top with no cable.

How to rebuild the power antenna - Cadillac Forums

www.cadillacforums.com > ... > Cadillac Tech Tips - How to fix it

May 9, 2009 - 15 posts - ‎12 authors
Remove the liner to access the antenna and disconnect ANY of the two ... If notlocked the motor receives continuously power and will drain ... Broken nylon wire lifting/lowering the antenna mast 4. ... The motor shaft comes out from the plastic casing after you take out ... Do not lubricate the cable or the mast.

Saabnet.comt Broken Antenna FAQ - The Saab Network

www.saabnet.com/tsn/faq/antenna.html
If the cable broke in the antenna, you need to remove the antenna to remove the ... take a 17 mm wrench and remove the nut over the antenna where the mast comes out of the body. ... Hopefully the chrome sleeve will come with the old mast. ... Be careful not to drop them down too far. get the motor assembly on a bench ...Missing: tacoma ‎1997

How To Repair A Broken Car Antenna -EricTheCarGuy ...

? 20:53
https://www.youtube.com/watch?v=zcKwFto9_s0
May 24, 2013 - Uploaded by EricTheCarGuy
This video shows one way you can deal with a broken antenna. ... Find out why ... this video is that I did ...Missing: chrome

Jan 12, 2016 | 1997 Toyota Tacoma

1 Answer

How do you replace radio antanna


What kind of car is it? If it is a fixed antenna you just unscrew the old one and screw on the new one. If it is an automatic antenna, you can buy either the motor or the mast. Assuming you just need to replace the mast, it comes with the plastic piece with the teeth on it. You need to remove the old broken plastic piece from the antenna motor. You might need to disassemble the antenna motor from the car to get enough of the plastic to grab onto with pliers. While you are pulling on it have someone turn on the radio to activate the antenna up motion and pull the old plastic piece completely out. With the old plastic runner out, the motor installed on the car, and the radio on, run the new plastic runner first through the doughnut screw that holds the mast to the car. Then cram the new plastic runner as far as you can into the hole that leads to the antenna motor. Then hold the very end of the mast (the tip), align the base to the opening as best you can and have someone turn off the radio to activate the down antenna motion. It goes quick so don't have your fingers where they can get pinched as the motor sucks in the plastic and the mast down into the hole. With the mast retracted, tighten the doughnut screw to that the mast won't flop out when you turn the radio back on.

Mar 12, 2015 | Cars & Trucks

1 Answer

Why does my hhr radio try to load and eject a cd disc when there isn't one inserted


There is an arm in/on the left side of the disc player. Most likely the spring inside it is broken. Leaving the arm in the pushed back position. Some times kids put coins in there also. This will cause things to happen, to include killing the radio and/or cd player.

Aug 14, 2014 | 2009 Chevrolet HHR

1 Answer

Right front and rear speakers don't work correctly


is it a factory radio? have you had any work done right before this concern your having?

Jan 24, 2013 | 2009 Chevrolet HHR

1 Answer

Right front and rear speakers come and go


is it a factory radio? have you had any work prior to this radio concern?

Jan 24, 2013 | 2009 Chevrolet HHR

3 Answers

How do you replace the atenna mast for 2005 sierra.


How do I install a new antenna on my GMC 05 2500 Sierra. I have to replace the base because it broke off. I've taken the dash off. But cannot seem to fish wire through the firewall.

Nov 26, 2010 | 2005 GMC Sierra

1 Answer

How to replace arial in 95 camry


This is normally due to a broken antenna mast inside the motor, the mast /cable assembly should be replaced, the antenna motor has to be removed from the car and disassembled to remove the broken piece of the old cable, once that is accomplished the antenna motor is reinstalled and the new cable assembly is fed into the motor by turning the radio on until the motor stops and then turning the radio off while feeding the new mast in.

Sep 04, 2009 | 1995 Toyota Camry

1 Answer

How to replace thunderbird antenna


please rate service.

Automatic Electric Antenna
Removal
  1. Lower electric antenna (18850) .
  1. Remove rear retaining screws of RH front wheel splash shield for access to antenna lower retaining bolt.
  1. Remove lower retaining bolt.
  1. Remove radio antenna nut (18865) from top of motor tube and remove electric antenna through fender/splash shield access.
  1. Disconnect signal cable and motor wire connector(s).
Installation
  1. To install, reverse Removal procedure.
  1. Tighten top radio antenna nut to 6-8 Nm (54-70 lb-in).
  1. Tighten lower electric antenna retaining bolt to 5.8-7.8 Nm (51-69 lb-in).
  1. Check operation of electric antenna and radio chassis .

    Automatic Electric Antenna


    1faf511.gif

mast
Mast, Power NOTE: A power antenna mast which is bent or broken can be replaced without replacing the motor and tube assembly.
Removal
  1. Remove radio antenna nut (18865) and radio antenna stanchion (18919) .

    ssd~us~en~file=l6389b.gif~gen~ref.gif

  1. Loosen retaining nut inside tube using 14 mm (9/16 inch) socket, and slide nut part-way up mast.
  1. Raise antenna to run plastic drive wire at bottom of mast out of motor. Note direction of teeth on plastic drive wire.
  1. Saw off damaged portion of antenna mast. Remove burrs from mast and slide nut and contact tube off stationary tube.
Installation
  1. With the teeth on the plastic drive wire facing toward motor on antenna, push end of plastic drive wire of replacement mast assembly down into tube. Push it around curve at bottom of tube until end enters drive mechanism.
  1. Run motor down while pushing on plastic drive wire until about 305 mm (12 inch) of wire has been drawn into the tube. Stop motor and insert bottom of antenna mast into tube. Lower mast.
  1. Slide contact tube and radio antenna nut down antenna mast. Tighten nut to 0.45 Nm (4 lb-in).

  2. Raise and lower antenna several times to ensure proper operation.
651247a.gif

Jul 09, 2009 | 1995 Ford Thunderbird

1 Answer

Replacing the antenna mast on Accord wagon


Make sure the broken mast is in the same state as the replacement mast (most likely fully retracted). There will probably be two connections on the unit, motor power and radio signal. Examine the latches on the motor power connector to see how the work; most likely you have to squeeze in a pair of plastic tabs while pulling on the connector (don't pull on the wires!) in order to unlock the connector.

Check the gasket around the antenna base. If it is hardened, and the replacement antenna does not have a good gasket with it, apply an automotive-grade body sealant or caulk to keep water from getting into the car body. (Many of those I've seen use a rubber base without a separate gasket; often this is hardened and will not seal without help once it's been removed.)

If the radio cable has a screw-on connector, put it on snugly finger tight. Cranking it on with a wrench may break the terminal inside (I've seen a number of TV tuners destroyed this way). However, most car antenna connections I've seen resemble over-sized phono plugs and jacks - push on and pull off. Often there is a protective sleeve or boot over the connector; you may have to pull it back along the cable first. Again, pull on the connector, not the cable. If that doesn't work, it may be a bayonet-style connector that you have to push in and rotate a quarter-turn counter-clockwise, then pull it off (I don't recall ever seeing that on an antenna, but it's mechanically possible).

Feb 26, 2018 | 1997 Honda Accord

2 Answers

Saab 9-3 convertable antenna will not go up. there is a clickng sound when the engine is turned off and on at the antenna.


antenna mast is no good.. you can buy a mast and have it installed or buy a used antenna and have it installed im sure Elite foreign auto parts has only saab parts.. tested and used,

Feb 17, 2009 | 2003 Saab 9-3

Not finding what you are looking for?
2009 Chevrolet HHR Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...