Question about Mercedes-Benz Cars & Trucks

1 Answer

Will a w208 coupe bonnet fit a w208 convertible

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Mercedes-Benz Master
  • 1,164 Answers

Yes it should do as long as the chassis numbers match up and part numbers match its only under the floor thats changed on the convertable who ever your buying it off should know orvtry before you buy

Posted on Jul 04, 2017


1 Suggested Answer


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Is there another way to open the bonnet on a fiat coupe 20v, if the lever in side the car does not work, please

Can you can get to the wire inside the vehicle? Try pulling it with a good set of grips or pliers. If not you will have to use a large flat blade screwdriver through the front grille to try and 'trip' the release lever at the actual latch. Try the attached YouTube link. It should work with the grille in position. Fiat Coupe Bonnet Release

Jun 07, 2018 | Fiat Cars & Trucks

1 Answer

Mercedes E550 Cabriolet front windshield wiper fuse location ?

I have a W208 so it might be slightly different.
Check the following locations.
Under the bonnet main fuse box.
Open drivers or passengers door and look behind the flap on the end of the dash that is hidden when you close the door.
in the boot (unlikely here) under the boot floor is the battery and another fuse box. (mainly for the rear electrics)
Your manual should list the locations. MB manuals tend to be actually useful.

Mar 29, 2017 | Mercedes-Benz Cars & Trucks

1 Answer

Where is the release catch situated on a 54 plate hyandai coupe ?

in the drivers side its a grey square thing near the bottom near the door frame just above the gas pedal and the over one is under the bonnet in the middle you have lift and feel for a little lever and lift the bonnet and its got a little arm at the side of the wing to put in bonnet to hold it up and make sure you keep the enjectors clean I had the coupe I loved iv got a cdx now 2005 if you more help

Jan 23, 2017 | Cars & Trucks

2 Answers

Hi, I have a 1995 Audi coupe, the bonnet is stuck on one side so when I pull the bonnet release the bonnet only pops up on one side. any ideas? thanks

get somone to push down on the bonnet and pull it up while u pull the relise handle. if dont work then strip the front grill and u should be able to open the catch manualy

Jul 10, 2013 | Cars & Trucks

1 Answer

Hi There, Newbie here... I have a mercedes benz E230 W210 (1996 model). Front inidcator lamps are gone and I cannot find them!! Opened the housing through the bonnet and checked but I can only find the H7...

The bulb holders are the smaller,usually white, twist locks directly above the large black headlight cover. It's tucked under the cross bar the bonnet catch bolts to. If there is no bulbs in there you will need the orange coated ones. If none of the indicators work check the fuses and the relay as well. MERCEDES W208 W210 FRONT TURN SIGNAL LIGHT BULB REPLACEMENT REMOVAL

Feb 22, 2018 | 1996 Mercedes-Benz E-Class

2 Answers

Hi how can i convert my 1976 4.2 damlier jagaur coupe from leaded fuel to unleaded fuel

The main difference is the non-lead version has hardened valves and seats in the cylinder head and a catalytic converter in the exhaust. You may be able to obtain a later head that fits this engine. The converter is an easy splice-in by cutting out a section of the exhaust header pipe and fitting suitable connectors. If you need to pass emission regulations, then it gets more complicated.

Oct 08, 2009 | Jaguar XJ Cars & Trucks

1 Answer

E36 bmw saloon

No, as far as I now there are no panels, doors, bonnet/hood, boot/trunk the same between the 2 door E36 Coupe & the four door E36 Saloon!

Mar 29, 2009 | 1996 BMW 318

1 Answer

89 celica fenders, front; will fenders from a coupe fit the converible

Only 87 -89 convertible fenders will work on the convertibles.

Jun 27, 2008 | 1989 Toyota Celica Liftback

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers


Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides