Question about Cars & Trucks

1 Answer

I have ply. grand voyager and the door locks are operating by them selves.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 15,575 Answers

Posted on Dec 15, 2017

Ad

5 Suggested Answers

Anonymous

  • 1 Answer

SOURCE: Central locking not working, Chrysler Voyager Limited 2005

hi this works on most voyagers disconect the possative terminal on the battery for ten minites excactly then reconnect and happy days your voyager centrol locking should work ok good luck

Posted on Feb 10, 2009

Ad

hribrahim

  • 90 Answers

SOURCE: 2002 Jeep Grand Cherokee electric door locks not operatin

the passenger door switch pack controls all door locks as this is the receiver from the remote you might want to try this and also check connections

Posted on Jun 22, 2009

Anonymous

  • 31 Answers

SOURCE: 98 Ply Grand Voyager, 1.4K miles with recurring P0305 code.

You say you changed the cap and rotor so I'm assuming the van has a 3.0L? Possible injector problem on cylinder #5, swap injector with cylinder 1 or 3 and see if miss/dtc moves to that cylinder. You also could have a vaccum leak, although they usually won't come and go. Does the vehicle have a consistent miss or do you just have a check engine light?

Posted on Aug 19, 2009

Testimonial: "Yes I have a 3.0L. I will swap out injector #5 with another cylinder. I can?t find any vacuum leak and was thinking on putting in a new EGR valve. The vehicle seems to have a consistent miss. The check engine light is on again. I started with error code P0300 and P0305. After I replaced the parts listed above the error codes went away, (no check engine light). Next day P0305 came back. "

bschilz

Bill Schilz

  • 2049 Answers

SOURCE: Needed serpentine belt diagram for a 91 ply. voyager 3.3L engine

Here's a link to the diagram you need...

http://www.gates.com/common/part_locator/view_diagram.cfm?id=S7006

Good luck and please rate this solution. Thanks.

Posted on Oct 17, 2009

Testimonial: "Looks good."

tuyen bui

  • 1025 Answers

SOURCE: how do you remove pass rear wheel bearing on 99

there are 4 bolt attaching the hub to the rear axle. remove those bolts and slide the hub bearing out

Posted on Mar 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

92 ply. grand voyager 3.3 v6 electronic dash gages quit operating


Check earth to dash or electronic system on car ie:-all conections are tight & not rusty

Aug 14, 2013 | Cars & Trucks

1 Answer

Power door lock relay


Check fuses, check relay operation, check switch, check actuator

Jul 25, 2013 | 1998 Plymouth Grand Voyager

1 Answer

I have a 98 ply grand voyager, and have heat from the drivers side vents, but cold air from the passenger side vents? please help


Does your van have seperate controls for driver and passenger temperature settings? If so the most likely cause is a broken actuator or broken passenger blend door. Unfortunately, the only way to repair a broken blend door is to remove the dash and the HVAC assembly.

Feb 05, 2011 | 1998 Plymouth Grand Voyager

1 Answer

1998 Grand Voyager: overhead lights on and off and door ajar light on ...


sounds like one of the door switches have come loose and causing it to earth out and activate the interior lights while driving which will also activate the chime.

May 17, 2010 | 1998 Plymouth Grand Voyager

1 Answer

1996 Ply Grand Voyager SE The blower motor


sounds like a faulty motor or relay

Oct 29, 2017 | 1996 Plymouth Voyager

1 Answer

Where is hatch sensor for 1998 Plymouth grand voyager (3.3 FLEX)?


its built into the lock mechanism lock might have to be replaced try adjusting it first. should be able to move the latch.

Jan 06, 2010 | 1998 Plymouth Grand Voyager

1 Answer

98 Ply Grand Voyager, 1.4K miles with recurring P0305 code.


You say you changed the cap and rotor so I'm assuming the van has a 3.0L? Possible injector problem on cylinder #5, swap injector with cylinder 1 or 3 and see if miss/dtc moves to that cylinder. You also could have a vaccum leak, although they usually won't come and go. Does the vehicle have a consistent miss or do you just have a check engine light?

Aug 19, 2009 | 1998 Plymouth Grand Voyager

1 Answer

I need location of fuel filter on 98 Ply G Voyager 3.3L


The fuel filter is located next to the fuel tank almost on top of it. It is pretty easy to change. You have to get a fuel filter for the right wheelbase. If you say you have a Grand voyager then you need a filter for an extended wheelbase. It comes with pieces of fuel lines attached to it which makes the difference in the wheelbase (longer lines for longer wheelbase).

Jun 03, 2009 | 2000 Plymouth Grand Voyager

1 Answer

The gadges in my 1997 plymouth grand voyager stopped working?


I Had The Same Thing Happen to Me in my 97 Ply. Grand Voyager,I Checked All THE Fuses and Tried to reset every thing by disconnecting the battery,still no help but being old school I just gave it a small whack atop of the dash board and everything started to work so if all else fails give it a whack and hope it falls in place might just be loose,hope this helps

May 11, 2009 | 1997 Plymouth Grand Voyager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

john h

Level 3 Expert

22486 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...