Question about Mitsubishi Cars & Trucks

1 Answer

Where is the crankshaft sensor located at in my 2000 mitsubishi eclipse

Posted by on

  • Grant Webb Mar 04, 2018

    Pic of sensor location

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 157 Answers

Where is the crankshaft sensor located at in my 20 - mit-irucehjaawd2evpa5h1fsprl-5-0.png

Posted on Mar 04, 2018

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 1 Answer

SOURCE: crankshaft position sensor location

if u pull the battery and battery tray u can easily reach this

Posted on Nov 23, 2008

Big Poppa Ma

Big Poppa Marv

  • 302 Answers

SOURCE: 2002 Eclipse

its by your intake manifold on the bottom of the engine block. there is a heat shield covering it which will need to be removed to get to it

Posted on Dec 06, 2008

Anonymous

  • 37 Answers

SOURCE: crankshaft position sensor location

Hello. One way to check if it is working is when you try to start the car does the needle move on you tac? If not then your crank sensor is more then likely the problem. It is located on the backside of the engine under the intake manifold. If is in about the center of the block. There will be a 10mm bolt holding the sensor in. If you decide to change it yourself (not to terrible of a job) unplug the sensor, remove the bolt and spin it back and forth slightly while pulling it out. It may be stoburn and you might have to work at it for a little bit (not a done of room) but it will come. When it's out the sensor will be shaped kind of like an L. I have changed a few of these over time and they can be a little stoburn. To install just reverse the process.

Posted on Mar 26, 2009

GARYca

Gary M

  • 672 Answers

SOURCE: Change a crankshaft position sensor on a 2000 eclipse

Is this a V6 or 4cyl???>>>(V6) This requires removing the Harmonic balancer (crankshaft pulley). Remove (R) front wheel, remove engine splash Guard, Remove crank pulley, remove lower timing belt cover. The Crank sensor is located behind the crank shaft pulley!! I highly recommend having this done by a certified tech, requires special tools. Hopefully this helps!!

Posted on Mar 11, 2010

Don Peterson

  • 1 Answer

SOURCE: I have replaced the camshaft sensor, Crankshaft sencor, computer, crankshaft pully, and new spark plugs on my 1999 Mitsubishi Eclipse and it still won't start, what could it be?

Engine needs spark, fuel and air to run. I assume the starter is turning the engine over. Have you verified you have spark at the plugs? Have you verified you have fuel pressure? Can you hear the fuel pump when you first turn the ignition key? If, yes to those, check the timing belt settings to make sure something hasn't caused the timing to change.

Posted on Mar 22, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Mitsubishi Eclipse GT 2dr Hatchback 3.8l crankshaft sensor location


It's under the timing belt cover in the one oclock position compared to the crankshaft.

Jun 23, 2017 | Mitsubishi Cars & Trucks

1 Answer

I have a 2000 eclipse 2.4 auto rs. Car just shut off while driving. Scanned the mil and showed a code for the camshaft position sensor. Car owners father replaced the crankshaft position sensor (dunno...


if the code shows a cam position sensor then it is the cam position sensor and not the crank position sensor
get the car to an accredited service center before it cost more money from inexperienced interference

May 28, 2017 | 2000 Mitsubishi Eclipse

1 Answer

Where isa the crank shaft position sensor located on a 2000 V6 Eclipse?


0996b43f8020334f.jpgAuston, I couldn't load both at the same time go to auto zone sign is (it free) and look it up

Sep 10, 2014 | 2000 Mitsubishi Eclipse

1 Answer

Crankshaft position sensor location


Look on the transmission bell housing

Dec 21, 2013 | 1995 Mitsubishi Eclipse

1 Answer

2000 Mitsubishi eclipse gt


see the diagram attached. God bless you
3163d4ca-779e-46fc-8616-1eb120b57e7d.jpg

Jul 22, 2013 | Mitsubishi Cars & Trucks

1 Answer

Change a crankshaft position sensor on a 2000 eclipse


Is this a V6 or 4cyl???>>>(V6) This requires removing the Harmonic balancer (crankshaft pulley). Remove (R) front wheel, remove engine splash Guard, Remove crank pulley, remove lower timing belt cover. The Crank sensor is located behind the crank shaft pulley!! I highly recommend having this done by a certified tech, requires special tools. Hopefully this helps!!

Mar 11, 2010 | 2000 Mitsubishi Eclipse

1 Answer

2002 Eclipse


its by your intake manifold on the bottom of the engine block. there is a heat shield covering it which will need to be removed to get to it

Dec 06, 2008 | 2002 Mitsubishi Eclipse

2 Answers

Crankshaft position sensor location


under hood, center, upper engine area, mounted on upper driver side of engine.

Nov 21, 2008 | 1996 Mitsubishi Eclipse

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

742 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...