Question about 1999 Oldsmobile Intrigue

Open Question

Bolt tightening sequence for water pump 1999 Olds Intrigue

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 104 Answers

SOURCE: on 98 intrigue water pump removal how do i clear the ps pully

Im not sure what engine you have since this information was not provided. But the Power Steering Pump pulley usually has some 'holes' on the pulley in which you can get a wrench through to loosen and remove the bolt.

Posted on Dec 30, 2008

Ad
ZJLimited

ZJ Limited

  • 17970 Answers

SOURCE: NEED 1999 olds intrigue serpentine belt diagram

1999 OLDSMOBILE INTRIGUE - V6 3.5L 214ci GAS FI N H
Belt Routing Diagram - Multiple Accesory
ba2f954.jpg


1999 OLDSMOBILE INTRIGUE - V6 3.8L 231ci GAS FI N K
Belt Routing Diagram - Multiple Accesory
9e23dfe.jpg


I hope helps with this (remember rated this help) Good luck.

Posted on Dec 23, 2009

ZJLimited

ZJ Limited

  • 17970 Answers

SOURCE: Head tourqe specs for 403 olds and bolt tightening

Fig. : Cylinder head torque sequence, 260, 307, 350 403 Oldsmobile built engines

5c04c01.jpg


On the V8, tighten the bolts, in the sequence illustrated, to 100 ft. lbs. When all bolts have been tightened to this figure, begin the tightening sequence again, and torque all bolts to 130 ft. lbs.

On V6's, tighten all head bolts in sequence to the following torques:
* All except bolts 5, 6, 11, 12, 13 and 14 - 100 ft. lbs.(19-135.5 Nm)
* Bolts 5, 6, 11, 12, 13, and 14 - 41 ft. lbs. (19-55.5 Nm)
* All bolts except 5, 6, 11, 12, 13, and 14 - 142 ft. lbs. (19-192.5 Nm)
* Bolts 5, 6, 11, 12, 13, and 14 - 59 ft. lbs. (19-80 Nm)

9fb545e.jpg

Hope this help (remember comment and rated this).

Posted on Mar 29, 2010

Testimonial: "Every thing I was looking for Thanks a lot"

Anonymous

  • 91 Answers

SOURCE: Changing water pump on a 1999 Oldsmobile Intrigue

Easy - drain coolant, remove pulley, remove drive belt, remove water pump bolts, reverse.
0c9a704.jpg
Check it out at http://99intrigue.shutterfly.com/waterpump

Posted on Apr 06, 2010

Anonymous

  • 91 Answers

SOURCE: Where is the Idle Control valve in a 1999 Olds

Find your throttle body (it's under the plastic cover):


4493617.jpg
The Idle Air Control Valve (IAC) is on its backside. Here it is with the manifold off (just for a better view, you don't need to remove the manifold):


3d24817.jpg
Hope this helps - if it does, give me some thumbs!

Posted on Apr 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sequence to torch water pump bolts on a 94 3.1Ltr. Buick century


Tighten the long bolts first then the rest of the short bolts. A torque sequence isn't necessary for a water pump.

Mar 29, 2017 | Buick Cars & Trucks

1 Answer

Need head bolt torque specs for 1999 Oldsmobile intrigue


Ian: According to Chuck on FixYa.com:

Head bolts are torque to yeild so you MUST use new bolts.

Tighten cylinder head retaining bolts in numerical sequence in three steps as follows:



  1. 20 Nm (15 lb-ft).




  1. 40 Nm (30 lb-ft).




  1. 50 Nm (37 lb-ft)


Loosen retaining bolts one at a time two to three revolutions and retighten as follows:



Long bolts:



  • Tighten to 40-50 Nm (30-37 lb-ft).

  • Rotate an additional 175-185 degrees.

  • Go to next bolt in sequence.


Short Bolts:



  • Tighten to 20-30 Nm (15-22 lb-ft).

  • Rotate an additional 175-185 degrees.

  • Go to next bolt in sequence.


Here is a pic of the sequence

http://i253.photobucket.com/albums/hh43/chuck943/Headboltsequence38L.gif

May 14, 2015 | Oldsmobile Cars & Trucks

1 Answer

Drilled and inserted 16 headbolt holes with time-sert inserts on a 2001 olds intrigue 3.5 when i torqued the heads one bolt did not seem to take as much force to turn as others but it seems tight do i...


Were to able to torque them all to spec? Did you torque in the proper sequence? If so, you are ok, but if you are still concerned, you could put some locktite on the bolt you feel is a bit lose.

Hope this helps.

Feb 18, 2011 | 1999 Oldsmobile Intrigue

1 Answer

How to replace a waterpump on a 2001 olds alero 2.4 cam


Water pump is driven by timing chain idler and is mounted on the rear of the timing chain housing. Disconnect the neg. battery cable. Drain cooling system. Disconnect oxygen sensor connector.
Remove upper exhaust manifould heat sheild. Remove exhaust manifold brace. Remove lower exhaust manifold heat sheild. Loosen manifold to exhaust manifold spring loaded nuts. Remove radiator outlet pipe to water pump coverbolts. Disconnect exhaust pipe from manifold.
Pull down on the exhaust pipe to disconnect it from exhaust manifold bolts. Disconnect outlet pipe from oil pan and transaxle. If equipped with manual tranaxle, remove exhaust maifold brace. Leave lower radiator hose attached and pull down on radiator out look pipe to disengauge from water pump. Leave outlet pipe hanging.
Lower vehicle. Remove exhaustmanifold to cylinder head nuts. Remove exhaust manifold to cylinder head nuts. Remove manifould. Remove timing chain front cover. Remove timing chain tensioner. Remove bolts bolts securing water pump cover to cylinder block. Remove water pump to timing chain housing nuts. Remove water pump attaching nuts. Remove water pump and cover assembly. Separate componets as necessary.
WHEN INSTALLING WATER PUMP MAKE SURE YOU FOLLOW THE TIGHTENING SEQUENCES THAT AFFECT SEALING. My frist one I messed up and broke the pump so becarful.
Installation
If cover was separated from body during removal, join this componets with a new gasket and hand tighten bolts. Apply bearing grease to splines of water pump drive. Set body and assemble into position.
Install and hand tighten bolts securing cover to cylinder block. Install and hand tighten bolts securing cover to cylinder block. Installand hand tighten nuts securing body to timing chain housing. Lubracate outlet pipe "O" ring with antifreeze. (I use RTV) Connect outlet pipe. Install and hand tighten bolts. Tighten bolts and nuts to specification in the following sequence. I'll ad the torque spec. at the end but this is where if you tighten out of order something will break.
pump assembly to timing chain housing nuts.
pump cover to pump body bolts
pump cover to cylinder block bolts (Bottom Bolt First)
outlet pipe to cover bolts
To complete installation reverse removel procedure.
Torque specs are 19 in. or 26mm all except water pump cover bolts which are 124 in or 14Nm
I never torque the bolts just make sure there done in the right order.

Oct 19, 2010 | Oldsmobile Alero Cars & Trucks

1 Answer

Head tourqe specs for 403 olds and bolt tightening


Fig. : Cylinder head torque sequence, 260, 307, 350 403 Oldsmobile built engines

5c04c01.jpg


On the V8, tighten the bolts, in the sequence illustrated, to 100 ft. lbs. When all bolts have been tightened to this figure, begin the tightening sequence again, and torque all bolts to 130 ft. lbs.

On V6's, tighten all head bolts in sequence to the following torques:
* All except bolts 5, 6, 11, 12, 13 and 14 - 100 ft. lbs.(19-135.5 Nm)
* Bolts 5, 6, 11, 12, 13, and 14 - 41 ft. lbs. (19-55.5 Nm)
* All bolts except 5, 6, 11, 12, 13, and 14 - 142 ft. lbs. (19-192.5 Nm)
* Bolts 5, 6, 11, 12, 13, and 14 - 59 ft. lbs. (19-80 Nm)

9fb545e.jpg

Hope this help (remember comment and rated this).

Mar 29, 2010 | 1984 Oldsmobile Cutlass

1 Answer

How do i install a water pump for an Isuzu Rodeo, V.7 3.2 liter


Isuzu_Rodeo_Rodeo_Sport_1997-2004
Water Pump - Removal and Installation

3.2L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    Negative battery cable Upper radiator hose Timing belt. Refer to the Timing Belt procedure. Idler pulley Water pump
To install:


d2081b9.jpg

Fig. Exploded view of the water pump mounting

3702807.jpg

Fig. Water pump torque sequence. Apply LOCTITE® 262 to bolt number 3 (arrow)-3.2L and 3.5L engines

NOTE Apply Loctite® 262 to bolt number 3 prior to installation.
  1. Install or connect the following:
    Water pump. Tighten the bolts in two passes, in sequence, to 18 ft. lbs. (25 Nm). Idler pulley. Torque to 38 ft. lbs. (52 Nm). Timing belt Upper radiator hose Negative battery cable
  2. Fill the cooling system.
  3. Start the engine and check for leaks.

3.2L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following: Negative battery cableRadiator hoseAccessory drive beltFront coverTiming belt. Refer to the Timing Belt unit repair section.Timing belt idler pulley Water pump
    Negative battery cable Radiator hose Accessory drive belt Front cover Timing belt. Refer to the Timing Belt unit repair section. Timing belt idler pulley Water pump

To install:

e6f48ad.jpg

Fig. Water pump bolt tightening sequence-3.2L engines
  1. Install or connect the following: Water pump. Tighten the bolts in sequence to 18 ft. lbs. (25 Nm).Timing belt idler pulley. Tighten the bolt to 38 ft. lbs. (52 Nm).Timing beltFront coverAccessory drive beltRadiator hoseNegative battery cable
    Water pump. Tighten the bolts in sequence to 18 ft. lbs. (25 Nm). Timing belt idler pulley. Tighten the bolt to 38 ft. lbs. (52 Nm). Timing belt Front cover Accessory drive belt Radiator hose Negative battery cable

  2. Fill the cooling system.
  3. Start the engine and check for leaks.

Hope this help (remember rated and commento).

Mar 19, 2010 | 1997 Isuzu Rodeo

1 Answer

Can't fill up my 1999 Olds Intrigue with gas,


the filler pipe has collapsed ,its need renewing

Oct 17, 2009 | 2000 Oldsmobile Intrigue

1 Answer

Diagram for removing a tensioner from 99 Olds Intrigue 3.8


Either in the center of the tension pulley or on the arm that the tension pulley is bolted to there is a square hole that is the size of the square on a 1/2" ratchet. Take a 1/2" ratchet and stick it in that hole and I think most of them you put it in the tighten position and pull on the ratchet. the tension will release and you can remove the belt.

Good Luck

Oct 12, 2009 | 1999 Oldsmobile Intrigue

4 Answers

Torque settings for cylinder head nissan sentra


Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees

Jul 18, 2009 | 1999 Nissan Sentra

1 Answer

Looking for directions, pictures, on how to change water pump


Water Pump Removal & Installation 3.0L (2V) To Remove:
  1. Drain the engine cooling system.
  2. Loosen the water pump pulley.
  3. Remove the bolt and the nut and position the roll restrictor bracket out of the way.
  4. Remove the accessory drive belt.
  5. Remove the generator.
  6. Remove the bolt and the accessory drive belt tensioner.
  7. Remove the nut, the bolt and the support bracket.
  8. Remove the bolts and the water pump pulley.
  9. Disconnect the water pump inlet hose and the crankshaft position sensor electrical connector.
  10. Remove the bolts and the water pump, and clean the sealing surfaces
To Install:
  1. Install the water pump. Tighten bolts in the sequence shown:
    • Tighten numbers 1-7 to 18 ft.-lbs. (25 Nm)
    • Tighten numbers 8-12 to 89 in.-lbs. (10 Nm)
  2. Connect the crankshaft position sensor electrical connector and the water pump inlet hose
  3. Install the support bracket.
  4. Install the accessory drive shaft tensioner.
  5. Install the generator.
  6. Install the roll restrictor bracket, bolt and the nut.
  7. Install the water pump pulley.
  8. Install the accessory drive belt.
  9. Connect the battery ground cable.
  10. Fill the engine cooling system.
2918819.gif
Water pump bolt torque sequence (3.0L (2V) engine)

Jun 26, 2009 | 2001 Ford Taurus

Not finding what you are looking for?
1999 Oldsmobile Intrigue Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

Jonah Oneal

Level 3 Expert

14092 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...