Question about Kia Cars & Trucks

Open Question

Im trying to rewire plug to the camshaft position sensor on 2002 kia optma?

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
fastboyz

paul erickson

  • 674 Answers

SOURCE: 2002 saturn sl1 camshaft position sensor

I hate to tell you this, but there is not Camshaft Position Sensor on any 1.9L Single or Dual OHC. I assume you had someone read a Diagnostic Trouble Code from your PCM. They probably told you that you needed a Camshaft Position Sensor, and then offered to sell you one. I would recommend changing your spark plugs and your plug cables with FACTORY REPLACEMENTS. This will usually make the DTC go away. Aftermarket plugs and wires rarely work well for this engine. If you are looking for a CRANKSHAFT position sensor, look between the engine and transmission on the back side of the transmission. It is also known as the "transmission input speed sensor". More often than not though, your engine will not fire up if the Crank position sensor is not working. Hope this helps.

Posted on Aug 24, 2008

Ad

Anonymous

  • 218 Answers

SOURCE: Camshaft Position Sensor Location

IF U GO TO THE RIGHT SIDE OF THE ENGINE AND LOOK 4 INCHES BEHIND THE BELT IT WILL BE ON TOP OF THE TIMING COVER.THE WIRES WILL BE RED/WHITE,BLACK,BROWN/WHITE

Posted on May 05, 2009

Jonah Oneal

  • 14092 Answers

SOURCE: Camshaft position sensor replacement for 2002 Audi A4

its not hard to fix.but you going to have to move some things to get to it. you will need a haynes repair manual.it will show you photos and instructions how to replace it.

Posted on Jul 05, 2009

timridenour9

  • 1 Answer

SOURCE: 2006 Kia Sorento code P0343 and P0463

did you ever get this fixed, i am having the same problem with mine, what was wrong with it

Posted on Dec 18, 2010

Keef2011

keith howells

  • 160 Answers

SOURCE: 2002 PT Cruiser. Vehicle shut

This could be related to a loose camshaft drive belt. If you have slack in the belt the camshaft will rebound on over run causing the P0340. It can also be a Crackshaft sensor problem too.(P0335) Hope this helps...

Posted on Mar 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How many camshaft and crankshaft sensors does my 2004 KIA Sorento have?


The camshaft position sensor is mounted on the engine near the camshaft gear by the ignition coils.The crankshaft position sensor is mounted on the engine near the crankshaft.

Nov 01, 2014 | 2004 Kia Sorento

1 Answer

My son's friends car died and they pushed in to my house. It cranks, seems week, no start, get a spark through the coils (2), the fuel pump turns on, the battery holds 12.5-12.6 volts and doesn't dro


- Faulty Camshaft Position Sensor
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery
It could be any of these if this is helpful please leave good feedback
Read more: http://engine-codes.com/p0340_ford.html#ixzz3EIFAq2Gh

Sep 24, 2014 | 2002 Kia Spectra

1 Answer

2004- Nissan Armada Where is the camshaft position sensor location on a V8 /5.6


the autodata book shows this engine as having 4 camshafts driven by chains
there will therefore be 2 cam position sensors ( one for each bank) as there are to drive chains
look at the rear of the block of each head or they could be inside the rocker covers
a workshop manual would be of immense help in working on the engine

Dec 07, 2012 | 2002 Kia Sedona

1 Answer

Kia cord po019


P0019 KIA - Crankshaft/Camshaft Correlation Error engine cyinder Bank 2 Sensor 2

Possible causes- Dirty Oil
- Engine mechanical problems
- Camshaft timing incorrectly set
- Faulty camshaft position sensor
- Faulty crankshaft position sensor
- Faulty actuator assembly

Jun 26, 2012 | Kia Cars & Trucks

1 Answer

Where is 2005 kia sedona camshaft position sensor located


By the camshaft reluctor wheel on the front of the engine by the belt side. Should be one bolt and a wire plug.
12597325-bnxnu01toi3wal15sq1bjmg4-1-0.jpg

Apr 28, 2012 | 2005 Kia Sedona LX

1 Answer

Kia rio not starting


Timing belt should have been changed at 60,000 miles. A loose timing belt or teeth missing from synchronous belt will lose timing. Damage to valves can occur if timing is not correct.

May 29, 2017 | 2004 Kia Rio

1 Answer

P1309 code showing on 2002 Kia sportage. Cannot pass smog.


Code PO1309 : Misfire Monitor Failure Description : When the misfire monitor is disabled,usually due to the input signal generated by the camshaft position sensor, by sensing the passage of teeth from the camshaft position wheel. Possible Causes : PCM(power train control module), Mass Air Flow Sensor, Engine Coolant Temperature Sensor, Crank Shaft Position Sensor, Camshaft Position Sensor.

Jan 31, 2010 | 2002 Kia Sportage

1 Answer

How to change spark plugs on 2002 mk4 automatic golf


1 - High Tension cable
  • 4 to 8 Kohms
  • With suppression connector and spark plug connector
  • Only remove and install spark plug connector using tool T10029
2 - Ignition coil with output stage (-N70-, -N127-, -N291-, -N292-)
Connection, ignition wires:
  • HV1 = Cylinder 1
  • HV2 = Cylinder 2
  • HV3 = Cylinder 3
  • HV4 = Cylinder 4
3 - 10 Nm 4 - Connector
  • 6 pin
5 - Knock sensor 1 -G61-*
  • Contacts gold plated
  • Fitting location: Cylinder block intake side
6 - 2-pin connector
  • For knock sensor 1 -G61-
  • Contacts gold plated
  • Do not interchange
7 - Knock sensor 2 -G66-*
  • Contacts gold plated
  • Fitting location: Cylinder block intake side
8 - 2-pin connector
  • For knock sensor 2 -G66-
  • Contacts gold plated
  • Do not interchange
9 - 20 Nm
  • Tightening torque influences the function of the knock sensor
10 - Spark plug, 30 Nm
  • Type and electrode gap See test data, spark plugs.
  • Remove and install with 3122B
11 - Connector
  • Contacts gold plated
  • 3 pin
12 - 10 Nm 13 - 100 Nm
  • Use counter- hold tool 3415 to loosen and tighten
14 - Camshaft sprocket
  • With rotor for Camshaft Position (CMP) sensor
15 - Camshaft Position (CMP) sensor -G40-* 16 - Bracket
  • For Camshaft Position (CMP) sensor

Jun 04, 2009 | 2002 Volkswagen Golf

1 Answer

Kia rio 2002 camshaft pos. sensor just replace still light check


check the belt,if its out it will flag up this code,your car will run on sequential firing from the crankshaft sensor,failing that put an oscilloscope on the signal wire at the sensor and ecu its possible the ecu might not be seeing the signal,start with the basics first

Dec 29, 2008 | 2002 Kia Sportage

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...