Question about Saturn Cars & Trucks
Will start and run once or twice then stall and wont start up but will if u pop the clunch
Clunch ? clutch Are those P codes ? P0327 an P0336
The knock sensor is a piezoelectric device that produces an output voltage based on mechanical engine vibration. The PCM will retard the electronic spark timing on the signal being received. The knock sensor produces an AC signal. The amplitude and signal frequency is dependent upon the knock level. During normal operation, the knock sensor system attempts to filter out all engine noise that is not caused by spark knock. The diagnostic test for DTC P0327 turns OFF all filtering during the first 20 seconds of engine run time. If a sufficient amount of noise is detected during the 20 second test, the diagnostic passes. If no noise is detected, the diagnostic fails. Since DTC P0327 is a type B code, the diagnostic must fail during 2 consecutive ignition cycles to set the DTC.
The crankshaft position (CKP) sensor defines engine position by generating an electrical pulse each time it passes by a notch of the crankshaft reluctor wheel. The PCM uses crankshaft sensor pulses for fuel delivery and spark timing.
Posted on Nov 07, 2019
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Listen under the hood next to fuse box for a cliking sound when ignition is turned. If you do not hear this click you many need a starter relay.
Posted on Dec 09, 2008
Have a look at this link, scroll to your engine & click on picture to expand for better view.
Posted on Jan 23, 2009
SOURCE: solution for 1998 saturn sl
Hello DTC P0341 & P0133 very common saturn Codes.You need to check condition of Plugs & wires,If not New Replace All Plugs & Wires,also I would replace the #1#4 Coil for the P0341.For the P0133 Reaplce your front O2 sensor with an OEM sensor,not an aftermarket.
Posted on May 11, 2009
SOURCE: 1993 Saturn SL stalling
First, if the SES light is on or comes on a little after it is running it has a code set in the computer. Itis easy to read the code on an OBD1 system by jumping the A-B terminals on the DLC Data Link, block under the drivers side see the following link for better explanination of reading the codes, http://www.troublecodes.net/GM/
Also review the following on the O2 Sensor and coolent temp sensor http://www.saturnfans.com/forums/showthread.php?t=37884 http://www.youtube.com/watch?v=XQ9vtD_ssjg, good luck you can fix this vehicle easily.
Posted on Jun 01, 2009
There is an interior fuse panel just to the left of the passenger's left knee. The cover It is held on by velcro. After you take off the cover, you will see a diagram on the inside of the cover telling you which fuse is for what. This is covered in your manual, which is in the glovebox. If you do not have a manual you can get one off ebay for a few bucks.
Posted on Jul 26, 2010
Tips for a great answer:
Nov 20, 2012 | 1998 Saturn SL
Oct 29, 2017 | 1998 Saturn SL
Jan 28, 2010 | 1998 Saturn SL
Jan 28, 2010 | 1998 Saturn SL
Nov 02, 2009 | 1998 Saturn SL
Oct 01, 2009 | 1998 Saturn SL
Aug 03, 2009 | 1998 Saturn SL
Jun 22, 2009 | 1998 Saturn SL
Mar 15, 2009 | 1993 Saturn SL
Dec 01, 2008 | 1998 Saturn SL
31 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: