Question about Dodge Cars & Trucks

1 Answer

Location of my egr valve on my 2001 dodge ram 5.2

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 6,152 Answers

Should be around the throttle body, look for cylinder and pipe.

Posted on Nov 24, 2019

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

josh1111

  • 398 Answers

SOURCE: egr valve location

The EGR Valve Location is typically housed on the intake manifold this schematic may help you
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528008822d

Posted on Mar 07, 2009

c17hydro

Greg Bernett

  • 2989 Answers

SOURCE: Location of EGR Valve

Found the info!!

This Dodge EGR valve is a certain kind of device that is mounted right on your intake manifold which controls the amount of exhaust gasses back into your engine.
On a 2005 Dakota with 4.7 liter engine (non-HO), the EGR valve is located near the intake manifold on the driver's side right up against the firewall. It's hard to spot as it sits lower than the intake manifold. To change it, remove the electrical connector. There's a red tab that needs to be pushed to one side and then you have to squeeze down on a tab to get it free. Using a 13 mm socket, remove the bolt that you can see. I had to use a 3 inch wobble extention and then a 8 inch extension with a deep well socket to reach it with my 3/8 inch ratchet. There's a second bolt that you can't see between the EGR valve and the firewall. With a little trial and error and a lot more luck, you can reach the hidden bolt with the 3 inch wobble extension and a 13 mm deep well socket. Attach the ratchet after the socket is on and remove. This one isn't easy and if there's any Dodge engineers reading this one, a couple of extra inches of clearance between the valve and the firewall wouldn't have killed you no matter what the cost accountants said. With both bolts removed, you should be able to pull out the metal pipe that connects the manifold to the EGR valve out of the manifold (Pull to the right) and then you can lift the valve out. For assembly, the metal pipe connecting the intake manifold the EGR valve has to be removed and reinstalled on the new valve. It's held on with 2 5/16th" bolts. You should put the rear bolt on tight, but leave the front bold loose for the reinstall as some adjustment is necessary to get it put back together and the rear is a pain to tighten when installed. Line up the bolts that attach the valve and get the rear 13 mm bolt (The one you couldn't see on disassembly) started. Do not start the other 13 mm bolt as you'll need to pivot the valve and pipe to the left in order to reinsert the pipe into the intake manifold. Once the pipe is in the intake manifold. Start the other 13 mm bolt and tighten both 13 mm bolts and then the 5/16" bolts holding the pipe onto the valve. Reinstall the electrical connection. Please don't forget to rate!!!!

Posted on Mar 14, 2009

ZJLimited

ZJ Limited

  • 17970 Answers

SOURCE: egr valve location on dodge ram 2005 4.7

The EGR, or exhaust gas recirculation valve, takes inert exhaust gasses drawn from the exhaust system and reintroduces them into the combustion chamber through the intake manifold. This process lowers the peak combustion temperature and helps combat the formation of Nitrous Oxide (NOx) in the exhaust.

f0255cf.jpg

  1. Separate the intake ducts from the air cleaner assembly by loosening the retaining clamps and pulling the ducts away from the housing.
  2. Disconnect the vacuum line from the air cleaner assembly.
  3. Remove the wing nut that secures the air cleaner housing lid to the base.
  4. Remove both the air cleaner hosing lid and base.
  5. Locate the EGR valve. Look at the front of intake manifold. The EGR valve will be bolted to the intake manifold just in front of the carburetor.
I hope help you with this. Good luck.

Posted on Sep 07, 2009

stevenhurc

Steve Hurc

  • 459 Answers

SOURCE: where is the location of the egr valve on a 2001

on petrol V6 engine its right rear side of inlet manifold(left side when looking into engine bay) see pics. below
diesel its on inlet manifold left side middle section of manifold

eb59265.jpg
2736ba4.jpg

Posted on Nov 02, 2009

Anonymous

  • 2 Answers

SOURCE: PCV valve location on a 2003 Dodge Ram pickup, 4.7?

It's on the side of the Oil filler container.

Posted on Mar 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Auto part store says there is no egr valve on 08 dodge ram 1500 4.7. True?


25 - Emissions Control/Exhaust Gas Recirculation, Gas/VALVE, Exhaust Gas Recirculation (EGR), 4.7L/Removal REMOVAL collapse.gif Labor Operations: Click to display a list of Labor Operations associated with this procedure

2431021.jpg The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head. An exhaust gas routing tube connects the EGR valve to the intake manifold.
1. Use a diagnostic scan tool to record any Diagnostic Trouble Codes (DTC). 2. Remove the throttle body resonator. 3. Perform the fuel system pressure release procedure (Refer to 14 - Fuel System/Fuel Delivery - Standard Procedure) 4. Disconnect and isolate the negative battery cable.


2430847.jpg 5. Disconnect the power brake booster vacuum hose (1) and the vapor canister purge hose (2) at the intake manifold.


2430720.jpg 6. Disconnect the EGR valve solenoid electrical connector (1).


2430801.jpg 7. Remove the EGR valve assembly retaining bolts (1). 8. Remove the EGR valve and the EGR routing tube from the engine as an assembly. 9. Remove and discard the metal gasket located between the cylinder head and the EGR valve assembly.


2433378.jpg 10. Remove the EGR valve routing tube retaining bolts (1) at the EGR valve assembly 11. Remove the EGR valve routing tube and discard the gasket.

Feb 14, 2012 | 2008 Dodge Ram 1500 2WD

2 Answers

Aside from the P0406 code, I'm also getting code P1561. Are they related and what can I do to fix it? I have 2006 Dodge Ram 1500.


The po406 is an egr code which is common for a bad egr valve, but check your wiring and check for plugged port or carbon lodged in valve, as far as the p1561 this is not a good code, this must of been gotten with a genric scan tool, i would fix the po406 and then reset the computer readiness monitors and drive it and go from there. hope this helps, good luck

Jan 10, 2011 | 2006 Dodge Ram 1500

1 Answer

I cant locate the egr valve on a 1998 Dodge ram 1500 5.2 L


An EGR valve assembly located at the front of the intake manifold. The EGR valve is a poppet style valve (on/off only) and is controlled by an internal diaphragm.

af91f0c.jpg

Fig. EGR location and associated components-California diesel

Hope helps (remember to rate this and comment ).

Sep 14, 2010 | 1998 Dodge Ram 1500 4WD

1 Answer

Egr valve location for 1996 dodge ram 1500 5.2 v8?


it should be behind intake just above the bellhousing, hard to reach, easiest from the bottom, if not there follow tubes from exaust manifold they connect to egr valve

Sep 10, 2010 | Dodge Ram 1500 Cars & Trucks

2 Answers

Where is the EGR valve on 1986 Dodge Ram D50 pickup 2.0cc 4 cyl


if there pipes or tubes on top of your exhaust manifold that is where your EGR valve should be. if you want diagrams or text to help fix this problem i suggest the book from Chilton. they tend to explain thing pretty well.

Oct 01, 2009 | 1986 Dodge Ram 50

2 Answers

Egr valve location on dodge ram 2005 4.7


The EGR, or exhaust gas recirculation valve, takes inert exhaust gasses drawn from the exhaust system and reintroduces them into the combustion chamber through the intake manifold. This process lowers the peak combustion temperature and helps combat the formation of Nitrous Oxide (NOx) in the exhaust.

f0255cf.jpg

  1. Separate the intake ducts from the air cleaner assembly by loosening the retaining clamps and pulling the ducts away from the housing.
  2. Disconnect the vacuum line from the air cleaner assembly.
  3. Remove the wing nut that secures the air cleaner housing lid to the base.
  4. Remove both the air cleaner hosing lid and base.
  5. Locate the EGR valve. Look at the front of intake manifold. The EGR valve will be bolted to the intake manifold just in front of the carburetor.
I hope help you with this. Good luck.

Sep 07, 2009 | 2005 Dodge Ram 1500

2 Answers

2005 Dodge 1500 code p0404 EGR valve.


The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head ,

  1. Remove electrical connector (5) at top of EGR valve solenoid.
  2. Remove tube mounting bolt (1) at intake manifold.
  1. Remove two bolts (4) connecting EGR tube (1) to valve assembly.
  2. Remove gasket located between EGR tube flange and EGR valve assembly.
  3. Remove two EGR valve mounting bolts (5).
  4. Separate valve assembly (3) from engine.
  5. Remove and discard metal gasket located between cylinder head and valve assembly.
INSTALLATION
  1. Clean area at rear of left cylinder head where it joins base of EGR valve.
  2. Clean EGR tube where it joins EGR valve.
  3. Position new gasket between EGR valve and cylinder head.
  4. Position EGR valve to cylinder head. Install and tighten two bolts (5). Refer to Torque Specifications.
  5. Position new gasket between EGR tube flange and EGR valve assembly.
  6. Position EGR tube (1) to side of EGR valve and into intake manifold.
    1. Install EGR tube flange bolt (1) at intake manifold. Tighten bolt. Refer to Torque Specifications.
    2. Connect electrical connector (5) to top of EGR valve solenoid (2).Do a final tightening of two EGR tube bolts (4). Refer to Torque Specifications

Feb 05, 2009 | 2005 Dodge Ram 1500

1 Answer

EGR Valve location


4.7 does not use an egr valve

Jan 05, 2009 | 2002 Dodge Ram Maxi

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...