Question about Dodge Cars & Trucks

1 Answer

Have a 2013 dodge avenger 2.4l coil on plug. It has a misfire no 1 swapped coils and it follows,bought a new coil and the same thing misfire PO301 and it still follows the coil.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Dodge Master
  • 30,365 Answers

Sounds like the new coil is faulty. Connect it to power, an ignition lead and a spark plug earthed to the block. When you disconnect the negative, you should get a big, fat blue spark.

Posted on Dec 08, 2019

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 188 Answers

SOURCE: 2004 chevy k2500. misfire

sound like you a cam shaft sensor going out and the sensor is not hitting the mark, makingit misfire.?????

Posted on Feb 04, 2009

Anonymous

  • 255 Answers

SOURCE: misfire in 1 & 2 cylinders after changing wires plugs and coil

since the problems appeared after the work, it is in the work. prob is in wires or plugs.. take no 1 plug out put it back in wire terminal, re install one of you old plugs into no 1 cylnder have someone turn eng. over ck for bright spark repeat for no 2. make sure plug gap is correct. if no fire to you plugs. then you know what to do replace the wires.

hope2help shack

Posted on Apr 16, 2009

Mr BrokRench

Mr BrokRench

  • 1623 Answers

SOURCE: Recurring #2 cylinder misfire.

Hello Mr Fixit...If memory serves me right, the PO352 B fault code would indicate #4 cylinder coil and PO352 A for #3. The
Possible causes ...faulty spark plug...faulty spark plug wire..faulty ignition coil pack..faulty PCM...open or short in wiring from PCM to iginition coil pack. To accurately troubleshoot and determine the problem you will need an oscilliscope and a diagnostic scanner. Without these you are basically guessing as to the cause.
The ignition control module is integrated into the PCM and a faulty ICM can definitely cause this trouble code...and i have seen my share of faulty PCM's.
Hope this helps and the best of luck to ya.

Posted on May 13, 2009

Anonymous

  • 1 Answer

SOURCE: misfire

Check your cam. position sensor

Posted on Jul 25, 2009

danielson57

Dan Connors

  • 119 Answers

SOURCE: 0301 misfire. Replaced spark plugs

take compression test

Posted on Dec 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have 2013 chrysler town and country van 3.6L engine need firing order


1-2-3-4-5-6
Head (horizontal)
135
246

Coil (vertical)
6 3
4 1
2 5

Jul 26, 2017 | Chrysler Cars & Trucks

1 Answer

Ford freestar 2006, cylinder 6 code po301 cylinder 1 misfire


Standing on the passenger side.looking at the engine. Number 1 is the first cylinder on your left. Follow the wire to the coil. unplug it at the coil, lay the end of the plug close to the tip of the cap and start the engine. If there isn't multiple sparks, replace the coil. If there is , replace the plug and or wire. If you still have a misfire after that, do a compression test on number 1 cylinder.

Jul 07, 2015 | 2006 Ford Freestar

1 Answer

My 2001 dodge Dakota is running rough and the check engine light is on.


You'll have to look up the actual procedure to test the coil for code 351. The code means the computer is not able to fire the coil on demand which could be caused by several things, including a faulty computer. It could also be a problem with the wiring between the coil and the computer.

Feb 17, 2015 | Dodge Cars & Trucks

1 Answer

What causes engine misfires to stay after new plugs and coil packs?


Try swapping the coil packs around - like swap #1 with #2, and swap #6 with #5, see if the misfires MOVE with the coil packs swapped to the new cylinders or if they stay with the cylinders. If they move with the coil packs, the new coil packs are bad. If they stay with the cylinders, there's a problem with those cylinders. You DID replace that camshaft sensor, right?

Have you checked your #1 and #6 injectors?

Aug 07, 2014 | BMW 528i Cars & Trucks

3 Answers

Have a missing on 08 f150 4.6 went to auto zone and got a code reading and it said probable cause is a sludge throttle body/air flow got cleaner for it and clean throttle body but it still misses some one...


it is possible for it to be a coil, the thing with fords are that it takes alot of time for the misfire counter to turn the check engine light on and at the smae time set a code for missfire, if you have a code reader available check to set if there is a po301-po302 -po303,and so on the p is for power tran the o is that it is a generic code 3 indicateds misfire, 01,02 indicate which cly. is misfiring , alot of time you have to drive the fords for awhile before it will set a misfire code. if you have a good scan tool you can go to mode 6 and check misfire counters for which cly. is missing. than you can check compression in that cly, chec coil and plug.

Oct 30, 2013 | Cars & Trucks

2 Answers

I have a 2008 dodge avenger se and my engine light is on and was flashing before. when it is in drive or park it turns off when i stop. i took it to auto zone and the told me that cylinder 3 and 4 misfire...


The best way to fault find in swap coil 1&2 with coil 3&4. If the fault doesn't change, it is possibly the plugs or something more sinister electrically.

Sep 18, 2017 | 2008 Dodge Avenger

1 Answer

CEL light flashing-shuddering when idle. 03 passat 1.8 Turbo. Thinking its an air leak somewhere? Can hear air but can't figure out where its coming from...


A flashing cel indicates misfiring. A common problem is a bad ignition coil. The easiest route for diagnosis is the check the trouble codes(autozone and some other parts stores will scan for free, or an OBDII code reader is not too expensive to buy). The code should tell you which cylinder is misfiring(PO301 means cyl #1, 302 cyl #2, etc). Once you know which it is, swap the ignition coils around. If you have a #1 misfire, swap coils 1 and 4, clear the codes, then check it again. If the misfire moves, you know you've got a bad coil. If the misfire is air or fuel related, as with an intake leak, other codes should come up as well as the misfire.

Feb 08, 2011 | 2003 Volkswagen Passat

2 Answers

Engine misfire


It sounds like the coil is going out on that cylinder,but replace the boot with the coil.It would not hurt to use a injector cleaner first,Lucas is the best.

Jan 25, 2010 | 2004 Mazda 6

4 Answers

HI I HAVE A 2001 MAZDA TRIBUTE AND THE CODES PO301 AND PO303 CAME UP IN THE DIAGNOSTIC REPORT. THE CAR TURNS OFF WHEN I WARM IT UP IN THE MORNING IN THE COLD AND AFTER THAT ITS FINE I ALREADY CHANGED THE...


cylinder 1 misfire and low compression. Plugs and wires changed plus new fuel injectors. The engines still misses and no one can find the cause. When put on the computer it read misfire cylinder 1.

Dec 31, 2008 | 2004 Mazda Tribute

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...