Question about 2002 Chevrolet S-10

1 Answer

It is 2 wheel drive and is the drive shaft it has wheel bearing support is 2 part drive shaft and the noise is after 55 like every second like scraping noise

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 6,927 Answers

It can be a u joint,or the drive shaft bearing,some call it drive shaft support bearing,or swing bearing.Moving the drive shaft up,and down should tell you if the swing bearing is bad,it should not have no movement up,or down,or side to side.It should stay centered in the housing,surrounded by rubber.

Posted on Nov 21, 2009

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Driving noise, not from bearings


it could be center bearing, if its going bad it can also cause a vibration, make sure you have sufficient fluid in the diff as well, you can also get a noise and vibration from collapsed motor or trans mounts

Oct 13, 2015 | 2005 Nissan Murano SE

4 Answers

What is the reason for front grinding when turning


This due to either a worn wheel bearing or a worn front drive arm.

The most common cause of a grinding noise when turning is a worn front wheel bearing. What happens is that the weight of the car is shifted on to that wheel as you make the turn causing the worn bearing to make a grinding noise.

Jun 02, 2014 | 2003 Ford Focus

1 Answer

1999 Lexus RX300 left rear wheel has a rumbling noise sounds like cv joint or bearing its all wheel drive.


Spin that wheel by hand as fast as you can. If you can hear the noise coming from right behind the tire it's probably a wheel bearing.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Sep 04, 2012 | 1999 Lexus RX 300

1 Answer

Suspected rear wheel bearing problem, but is there a second bearing just at th drive shaft on the rear rhs that could be causing the noise.? 2005 freelander td4. Thanks billy


Hi Billy

If it is just a wheel breaing then it's not to much to worry about, they are fairly cheap and easy to do, the other bearing is from the 4 wheel drive system is is somewhat more problematic worst case is the diff / gearbox may have failed, does the wheel drive work well? is the noise more or less when in 2 wheel?

there is a few possiblities so get back to me with more info and I will be able to help.

Regards

Dan

Dec 30, 2010 | 2002 Land Rover Freelander

1 Answer

How to replace rear wheel bearing on 1994 bmw 325i


3-Series (Except M3, M Roadster, M Coupe, 318ti & Z3)

1. Raise and support vehicle. Remove wheel(s).
2. Remove axle shaft. See appropriate AXLE SHAFTS article.
3. Remove brake disc. See BRAKE DISC .
4. Screw special tool (33 2 116) onto drive flange with wheel studs. Drive out drive flange with special tool (33 4 201/202/203). See Fig. 33.
5. If necessary, pull off bearing inner race using special tool (00 7 500) and a thrust piece. See Fig. 34.
6. It may be necessary to remove inner wheel bearing race with the following procedure:
  • Detach wheel bearing inner race with special tool (33 4 400) through groove in bearing inner race.
  • According to outside diameter of bearing inner race, use special tool 33 4 401 with: 33 4 405 for dia. 45-51 mm, 33 4 406 for dia. 50-55 mm and 33 4 407 for dia. 55-61 mm in groove. See Fig. 35.
  • Tension special tool 33 4 401 with wrenches 33 4 403 and 33 4 404 until it can still just be turned in groove. See Fig. 36 .
  • Screw in special tool 33 4 402. Detach inner bearing race.
7. Remove circlip. See Fig. 37 .
8. Remove wheel bearing with special tool 33 4 031/ 041/ 042/ 043/ 045. See Fig. 38 .

CAUTION: Do not reuse old wheel bearing.

9. Draw in new wheel bearing with special tool 33 4 041/ 042/ 043/ 047. For inner bearing race 42 mm use special tool 33 4 049 and for 39 mm use 33 4 046. See Fig. 39 .
10. Installation is reverse of removal.
11. Replace stretched or damaged circlip. Ensure correct seating.
12. Pull in drive flange using special tool 33 4 041/ 042/ 043/ 045/ 048. See Fig. 40 .
13. Install brake disc.
14. Install axle shaft.


91stt_11.jpg

91stt_12.jpg

91stt_13.jpg

91stt_14.jpg

91stt_15.jpg

91stt_16.jpg

91stt_17.jpg

91stt_18.jpg

Nov 12, 2010 | BMW 325 Cars & Trucks

1 Answer

Gear whine at speed 55-75


have the center bearing in the drive shaft checked, cold weather can even sound like a faint siren like a cop is pullin ya over, ....
front wheel bearings are somewhat common also

Jan 10, 2010 | 2004 Jaguar X-Type

1 Answer

High speed vibration


The drive shaft needs to be replaced.its slightly bent or damaged.Check end float on both drive shafts for excesive movement.Also check for lift in the driveshaft gearbox bearings.Hope that is helpfull.good luck.

Jul 11, 2009 | 2002 Toyota Camry

Not finding what you are looking for?
2002 Chevrolet S-10 Logo

Related Topics:

331 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...