Question about 2005 Kia Sorento

1 Answer

2005 kia sorento crank shaft position sensor where is it located?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I HAVE A 2005 KIA SORENTO V-6. MY PROBLEM STARTED WHEN I WOULD DRIVE ON TO THE HWY IT WOULD PUTTER LIKE IF I WAS LOSING POWER. THE HOLE TIME THIS WAS GOING ON MY GAS GAGE WOULD NOT WORK. SO I WENT OUT TO AUTO ZONE HERE IN MADERA CA AND BOUGHT A DIAGNOSTIC TESTER AND THE CODE NUMBER P0338 WHICH MEANS CRANK SHAFT CENSER IS GONE. SO WHEN YOUR GAS GAGE STOP WORKING GET YOUR CAR TESTED OR THE BEST WAY TO GO IS TO INVEST IN A DIAGNOSTIC TESTER. IT WILL SAVE YOU A LOT OF MONEY

Posted on Jul 09, 2012

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 1 Answer

SOURCE: 2005 Subaru Baja Crank Shaft Position Sensor

is there a problem using e10 ethonal in a subaru impreza wrx 2003

Posted on Nov 24, 2008

Anonymous

  • 37 Answers

SOURCE: crankshaft position sensor location

Hello. One way to check if it is working is when you try to start the car does the needle move on you tac? If not then your crank sensor is more then likely the problem. It is located on the backside of the engine under the intake manifold. If is in about the center of the block. There will be a 10mm bolt holding the sensor in. If you decide to change it yourself (not to terrible of a job) unplug the sensor, remove the bolt and spin it back and forth slightly while pulling it out. It may be stoburn and you might have to work at it for a little bit (not a done of room) but it will come. When it's out the sensor will be shaped kind of like an L. I have changed a few of these over time and they can be a little stoburn. To install just reverse the process.

Posted on Mar 26, 2009

tunde007

Tunde Autos

  • 2382 Answers

SOURCE: where is the crankshaft position/crank

Hi, at the front of the crankshaft. if its near time for the timing belt, you want to replace it along with any pullies, tensioner and water pump


The crankshaft position sensor is mounted on the engine near the crankshaft.

Operation

The crankshaft position sensor is a Hall-Effect sensor that senses the crank angle (piston position) of each cylinder and converts it into a pulse signal. The signal from the sensor is relayed to the ECM to indicate engine rpm and the position of the crankshaft.

Removal & Installation

  1. Disconnect the negative battery cable.
  2. Disconnect the connector from the sensor.
  3. Remove the bolt that retains the sensor in place.
  4. Remove the sensor from its mounting. To install:
    1. Installation is the reverse of the removal procedure.
    2. Clearance between the sensor and the sensor wheel should be 0.020-0.059 inch. 2002-2005
      1. Properly connect the scan tool.
      2. Start the engine and allow it to idle.
      3. Be sure the idle position switch is ON.
      4. Specifications are as follows:

        Temperature - 4°F, test specification 1500-1700 RPM Temperature 32°F, test specification 1350-1550 RPM Temperature 68°F, test specification 1200-1400 RPMTemperature 104°F, test specification 1000-1200 RPM Temperature 176°F, test specification 650-850 RPM

Posted on Mar 16, 2011

co7196

Ned C Cook

  • 3433 Answers

SOURCE: Where is the crank shaft positioning sensor

Look at the area around the crankshaft pulley. It's bolted to the block and senses the crank position. If it fails, You won't have an ignition spark. Good Luck, Ned

Posted on Aug 27, 2009

Roger Foster

  • 701 Answers

SOURCE: where is the crank position sensor located in 2005

Hello martinezmelm: My name is Roger and I can answer your question. To locate the crankshaft position sensor. You will need to remove the timing cover. You will find the sensor on top of the crankshaft gear. Between the V of the timing belt.
Should you need further help please just ask. Please rate the answer as this way I know it was helpful. Thank You for using Fix Ya. Roger

Posted on Oct 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 03 kia sorento that i just changed the timing belt and water pump on. It drove fine for about 10 mins but then stalled. After 15 mins it starts, runs for 10 mins, rough again and stalls out.


run fault codes
check for wiring on crank shaft position sensor or cam position sensor/s
it will be something that was affected by the belt replacement procedure

Feb 14, 2017 | Kia Cars & Trucks

1 Answer

How to fix 2012 kia sorento camshaft sensor


replaced crank and cam sensor [Archive] - Sorento Nation - KIA ...

www.sorentonation.com/forum/archive/index.php/t-913.html

20 posts - ‎6 authors
replaced crank and cam sensors put back together cranked up very rough idle some tapping any ... 12-17-2012, 12:24 AM ... It's a 2006 3.5 Kia Sorrento. ... I found theproblem the SUV has a aftermarket alarm and remote start system I tripped ...

Kia Rio Crankshaft Position Sensor Replacement - YouTube

? 4:44
https://www.youtube.com/watch?v=hihQxMWuSFY
Mar 21, 2014 - Uploaded by Jason Roush
While looking for how to replace a Kia Rio crankshaft positionsensor, ... is on and i have a P0340 code, think this is theproblem? kia rio 2002.

Kia Sorrento/Sedona: 3.5 Litre Engine/Timing Belt/Crank ...

? 20:23
https://www.youtube.com/watch?v=CjaD_zYPrUA
Mar 29, 2014 - Uploaded by JamieJones TheCarMan
Repair and/or Replacement tips for timing belt, crank sensor,cam sensor, water pump and drivebelt ...

Crankshaft position sensor - 2003 Kia Sorento - RepairPal

repairpal.com > Questions > Kia > Sorento > 2003 Kia Sorento


Jan 20, 2016 | 2012 Kia Sorento Base 4dr SUV 2.4L 4-cyl....

2 Answers

Can you bypass a camshaft position sensor on a 2005 kia sorento. with out replacing it?


no you can`t because it will affect fuel and set codes in the computer.

Mar 19, 2015 | 2005 Kia Sorento 3.5

1 Answer

How do you change battery cables in a 2005 kia sorento lx


If a car like yours dies while driving then I would suspect a fuel pump issue or a crank position sensor issue. Has your timing belt been replaced? that should be done at 100k miles. If the timing belt is coming apart it will throw pieces of itself onto the crank position sensor. Have someone check the fuel pressure and inspect the timing belt and crank sensor.

Apr 11, 2014 | Ford Escort Cars & Trucks

1 Answer

L have a 2003 Kia Sorento, sometimes it will just turn over but won,t crank. after a while it will start up. or l can be driving down the road and it will start poping and cut off, and won,t start.it does...


It will be a position sensor problem Check the air gap and check that the censor rotor is tight and that there is no material getting in the air gap causing a problem

Jan 06, 2014 | Kia Cars & Trucks

1 Answer

Location of camshaft position sensor for 2005 Kie Sorento


If it's an overhead cam, which I think it is, then it should be toward the very front of the engine, likely within the timing case. There should be some wires coming from it. It's usually a small black sensor.

Nov 12, 2012 | 2005 Kia Sorento 3.5

1 Answer

Replacing crankshaft position sensor on 2005 kia sorento


Vehicle 2005 Kia Sorento
after 10 t0 20 minutes will shot down 10 minute to 15 will start again, I check all fuses any clue

Oct 09, 2012 | 2005 Kia Sorento

1 Answer

Where is the crank shaft position sensor located


the crank shaft position sensor is part of the timing belt system. if your going threw the trouble of doing the sensor consider doing the timing belt as well heres a pisture to help you locate it. hope this helpsonetufshoppe_72.gif

Jan 28, 2011 | 2005 Kia Sorento

Not finding what you are looking for?
2005 Kia Sorento Logo

2,368 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...