Question about 1998 Volvo V70

2 Answers

I have a P0455 Evap code and so far 3 visits to the mechanic cost me $1700 and it's still not fixed. They replaced the purge control valve, vacuum hoses, purge control valve filter, fuel tank pressure sensor and seals and checked for the latest software on car computer. Help me please!

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 18 Answers

Did you get all the evap canister hoses replaced? This is usually caused by a U-shaped hose connecting the canister to the fuel breather system which breaks down much quicker than a straight hose due to high pressure. The S70 has a J-shaped hose and is much easily accessible. But in the V70, it is tucked just above the rear suspension and is much harder to see let alone change. The best way to do it is remove the fuel filter and its bracket. Hose is in a small space just behind it. However, I have done it by just unscrewing the fuel filter and very slightly tucking it out of the way (without removing any fuel lines). If you don't remove the fuel filter though, you need to take the right rear wheel off just to remove the other side of the hose.

Posted on Dec 30, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Volvo Expert
  • 133 Answers

Check the charcoal canister

Posted on Feb 26, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code p0455 on envoy 2004


large evap leak --check gas cap that it is on --look under truck at rear of fuel tank by spare tire and check the evap canister and hoses the following link will assist you
https://www.obd-codes.com/p0455 How to Fix Check Engine Light P0455 Emissions Purge Valve Replacement How to Fix Check Engine Light P0455 Emissions Purge Valve Replacement

Sep 19, 2016 | Cars & Trucks

1 Answer

My 06 cobalt has these codes can anyone tell me what they mean? Are they an expensive fix? p0446,p0455, p0172


code p0446 refers to evaporative emission (EVAP) system-vent control-circuit malfunction===causes --wiring--EVAP canister purge valve--ECM
code p0455 refers to EVAP system-large leak detected===causes --hose connections--intake leak--EVAP canister---EVap canister purge valve
code p0172 refers to system too rich, bank 1===causes intake blocked---EVAP canister purge valve--fuel pressure ---EGR system---injector/s ---ECM
because the EVAP purge valve appears in all codes I would be inclined to change that unit first the run the fault codes again

Jul 23, 2015 | 2006 Chevrolet Chevrolet Cobalt LT

2 Answers

I would like to know what the code PO455 on a 2007 Mitsubishi Endeavor means.


Possible causes
- Missing or loose fuel cap
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap
- EVAP canister or fuel tank leaks
- EVAP system hose leaking
- Fuel tank leaking
help.jpg What does this mean? Tech notes
The P0455 it's a very common code, because the code is set if the gas cap is loose or missing. Start by tighten the gas cap and clearing the code. In most cases the code can be clear by disconnecting the car battery for about 30 minutes.
help.jpg What does this mean? When is the code detected?
Evaporative Emission System (EVAP) control system has a very large leak such as fuel filler cap fell off, EVAP control system does not operate properly.
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Possible a noticeable fuel odor caused by the release of fuel vapors
P0455 Mitsubishi Description
This diagnosis detects leaks in the Evaporative Emission System (EVAP) purge line using engine intake manifold vacuum. If pressure does not increase, the Engine Control Module (ECM) will check for leaks in the line between the fuel tank and EVAP canister purge volume control solenoid valve under the following vacuum test condition.
The vacuum cut valve bypass valve is opened to clear the line between the fuel tank and the EVAP canister purge volume control solenoid valve. The EVAP canister vent control valve will then be closed to shut the EVAP purge line off. The EVAP canister purge volume control solenoid valve is opened to depressurize the EVAP purge line using intake manifold vacuum. After this depressurization is implemented, the EVAP canister purge volume control solenoid valve will be closed.

Read more: http://engine-codes.com/p0455_mitsubishi.html#ixzz3NlVyARyX

3022.gif

Dec 30, 2014 | Cars & Trucks

1 Answer

Computer code 455


Possible causes - Missing or loose fuel cap
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap
- EVAP canister or fuel tank leaks
- EVAP system hose leaking
- Fuel tank leaking The P0455 it's a very common code, because the code is set if the gas cap is loose or missing. Start by tighten the gas cap and clearing the code. In most cases the code can be clear by disconnecting the car battery for about 30 minutes.

When is the code detected? EVAP control system has a very large leak such as fuel filler cap fell off, EVAP control system does not operate properly. Possible symptoms - Engine Light ON (or Service Engine Soon Warning Light)
- Possible a noticeable fuel odor caused by the release of fuel vapors P0455 Buick Description This diagnosis detects leaks in the Evaporative Emission System (EVAP) purge line using engine intake manifold vacuum. If pressure does not increase, the Engine Control Module (ECM) will check for leaks in the line between the fuel tank and EVAP canister purge volume control solenoid valve under the following vacuum test condition. The vacuum cut valve bypass valve is opened to clear the line between the fuel tank and the EVAP canister purge volume control solenoid valve. The EVAP canister vent control valve will then be closed to shut the EVAP purge line off. The EVAP canister purge volume control solenoid valve is opened to depressurize the EVAP purge line using intake manifold vacuum. After this depressurization is implemented, the EVAP canister purge volume control solenoid valve will be closed.
if tightening the cap or replacing the cap does not help take your car to a shop to have it diagnosed as it requires special tools/equipment to test this and get an accurate results to find what needs replacing.

Oct 10, 2014 | 2004 Buick LeSabre

1 Answer

P0544 Code and problems with my Mechanics!


There is no code P0544 , maybe you mean P0455 ?
The control module tests the evaporative emission (EVAP) system for a large leak. The control module monitors the fuel tank pressure (FTP) sensor signal to determine the EVAP system vacuum level. When the conditions for running are met, the control module commands the EVAP canister purge solenoid valve OPEN and the EVAP canister vent solenoid valve CLOSED . This allows engine vacuum to enter the EVAP system. At a calibrated time, or vacuum level, the control module commands the EVAP canister purge solenoid valve closed, sealing the system, and monitors the FTP sensor input in order to determine the EVAP system vacuum level. If the system is unable to achieve the calibrated vacuum level, or if the vacuum level decreases too rapidly, this DTC sets.

It's called EVAP purge solenoid , the front one . An your Mechanic is probably not full of it . You need to know how the system works . If the computer set's a code for that system , it will not test it again till it's fixed an sometime other problems come up . After he fixed the first problem he should have told you that after a day or two or a couple of key cycles , starting the car cold till warm an a cold start again , sitting over night , 8 hours . Then the computer will retest the system . An other codes may set . Before putting blame , you should have to read about OBD 2 emissions , before being able to have a vehicle .

Mar 20, 2017 | 2004 Pontiac Grand Prix

1 Answer

Engine light code p0455 chev monte carlo


Hello,The problem is that the EVAP system is not able to achieve or maintain vacuum during the diagnostic testThe control module tests the evaporative emission (EVAP) system for a large leak. The control module monitors the fuel tank pressure (FTP) sensor signal to determine the EVAP system vacuum level. When the conditions for running the test are met, the control module commands the EVAP canister purge solenoid valve OPEN and the EVAP canister vent solenoid valve CLOSED . This allows engine vacuum to enter the EVAP system. At a calibrated time, or vacuum level, the control module commands the EVAP canister purge solenoid valve closed, sealing the system, and monitors the FTP sensor input in order to determine the EVAP system vacuum level. If the system is unable to achieve the calibrated vacuum level, or the vacuum level decreases too rapidly, the PCM will set the code you now have.So, you either have a stuck open purge valve, a stuck open vent valve, a false reading fuel tank pressure sensor, or a cracked/broken EVAP line.

Sep 21, 2012 | 2004 Chevrolet Monte Carlo

1 Answer

How do I resolve diagnostic code P0455 on my 2005 Chevrolet Tahoe?


Here is the definition and possible causes.

Possible causes - Missing or loose fuel cap
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap
- EVAP canister or fuel tank leaks
- EVAP system hose leaking
- Fuel tank leaking
P0455 CHEVROLET Description This diagnosis detects leaks in the Evaporative Emission System (EVAP) purge line using engine intake manifold vacuum. If pressure does not increase, the Engine Control Module (ECM) will check for leaks in the line between the fuel tank and EVAP canister purge volume control solenoid valve under the following vacuum test condition.


The vacuum cut valve bypass valve is opened to clear the line between the fuel tank and the EVAP canister purge volume control solenoid valve. The EVAP canister vent control valve will then be closed to shut the EVAP purge line off. The EVAP canister purge volume control solenoid valve is opened to depressurize the EVAP purge line using intake manifold vacuum. After this depressurization is implemented, the EVAP canister purge volume control solenoid valve will be closed.
Read more: http://engine-codes.com/p0455_chevrolet.html#ixzz24fVfq0Bx

Aug 26, 2012 | 2005 Chevrolet Tahoe

2 Answers

P0449 and P0455 error code 2008 2wd gmc envoy 30,203 miles


P0449 - Evaporative Emission Control System Vent Valve/Solenoid Circuit Malfunction

P0455 - Evaporative Emission Control System Leak Detected (no purge flow or large leak)

Both are refer at EVAP system; other EVAP DTCs: P0440 - P0441 - P0442 - P0443 - P0446 - P0453 - P0455 - P0456

This indicates a fuel vapor leak or lack of purge flow in the EVAP control system. It means a large leak has been detected. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

Symptoms: You likely won't notice any drivability problems.
Causes: most likely means one or more of the following has happened:
A loose or improperly affixed gas cap
A non-conforming gas cap (i.e. not factory/original brand)
Other leak or damaged piece in EVAP system

Possible Solutions: the most common repair is to:
Remove and reinstall the gas cap, clear the codes, and drive for a day and see if the codes come back.
Otherwise, replace the gas cap, and/or
Inspect the EVAP system for cuts/holes in tubes/hoses (you may hear a vacuum noise or smell fuel), repair if necessary


Hope helps.

Apr 23, 2011 | 2008 GMC Envoy

2 Answers

Service engine Diagnosis Code PO455 Transmission revs up


Hi, the code indicates a fuel vapor leak or lack of purge flow in the EVAP control system. It means a large leak has been detected. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

p0455 most likely means one or more of the following has happened:
  • A loose or improperly affixed gas cap
  • A non-conforming gas cap (i.e. not factory/original brand)
  • Other leak or damaged piece in EVAP system


With a p0455, the most common repair is to:

  • Remove and reinstall the gas cap, clear the codes, and drive for a day and see if the codes come back.
  • Otherwise, replace the gas cap, and/or
  • Inspect the EVAP system for cuts/holes in tubes/hoses (you may hear a vacuum noise or smell fuel), repair if necessary

Mar 05, 2011 | 1999 Ford Taurus

1 Answer

I have a toyota matrix w/ 88,000 miles 2006. I have the check engine light on, took it to advance auto, codes are PO441- EVAP control system , purge flow-fault also PO455 EVAP system-large leak I don't...


P0441 Evaporative Emission Control System Incorrect Purge Flow
OBD-II Trouble Code Technical Description

Evaporative Emission Control System Incorrect Purge Flow
What does that mean?

This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

EVAP emission canister purge is contolled by a valve which allows engine vacuum to pull stored fuel vapors from fuel tank into the engine to be burned, rather than be vented to atmosphere. A vacuum switch is used to detect when flow exists. If the PCM commands purge and sees that the switch is closed (indicating no detected purge flow) P0441 is set.
Symptoms

Likely, no symptoms will be discernible to the driver, other than the illuminated Check Engine Light.
Causes

A code P0441 could mean one or more of the following has happened:

* Bad vacuum switch
* Broken or damaged EVAP line or canister
* Open in PCM purge command circuit
* Open or short in Voltage feed circuit to Purge Solenoid
* Faulty purge solenoid
* Restriction in EVAP solenoid, line or canister
* Corrosion or resistance in purge connector
* Bad PCM

Possible Solutions

With a P0441 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

* Common Chrysler fix - Replace Leak Detection Pump / LDP
* Repair damaged EVAP lines or canister
* Repair open or short in voltage feed circuit to Purge Solenoid
* Repair open in PCM purge command circuit
* Replace purge Solenoid
* Replace vacuum switch
* Repair restriction in Evap line or canister or soleniod
* Repair resistance in purge connector
* Replace PCM
THIS IS LIKELY FROM TOPPING OFF THE TANK EACH TIME YOU FUEL UP



P0455 is similar:

Technical Description

Evaporative Emission Control System Leak Detected (no purge flow or large leak)
What does that mean?

This indicates a fuel vapor leak or lack of purge flow in the EVAP control system. It means a large leak has been detected. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.
Symptoms

You likely won't notice any drivability problems.
Causes

A code p0455 most likely means one or more of the following has happened:

* A loose or improperly affixed gas cap
* A non-conforming gas cap (i.e. not factory/original brand)
* Other leak or damaged piece in EVAP system

Possible Solutions

With a p0455, the most common repair is to:

* Remove and reinstall the gas cap, have AutoZone clear the codes, and drive for a day and see if the codes come back.
* Otherwise, replace the gas cap, and/or
* Inspect the EVAP system for cuts/holes in tubes/hoses (you may hear a vacuum noise or smell fuel), repair if necessary

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Sep 05, 2010 | 2006 Toyota Matrix

Not finding what you are looking for?
1998 Volvo V70 Logo

841 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...