Question about 1999 Daewoo Lanos

1 Answer

Daewoo lanos how do i replace the cv gaiter please

Posted by on

  • Anonymous Apr 20, 2010

    Thanks that was most helpful, I need to go and buy the tools to do it, do you know the size of the large nut in the centre of the wheel please



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 63 Answers

Hi, most hyundai's you just undo the large drive shaft nu in the centre of the wheelnutst, the 2 bolts securing the strut(shocker) to the stub axle, sometimes you have to pop the tie rod end as well & even the inner control arm bolt, turn the stub full lock so you can get the shaft out through the back of it, then lever the shaft out of the diff with a screwdriver. Usually you have to pull the shaft appart to change the rubber boot, you'll need circlip pliers for this & it's pretty self explanatory which end to pull appart. It's a good idea to clean the grease off first so you can see what you're doing, good luck, hope this helps :)

Posted on Apr 20, 2010


1 Suggested Answer


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

CV Joint replacement

Try, an online shopping site. They have a huge inventory, and cheapest prices anywhere.

Jul 09, 2013 | Daewoo Cars & Trucks

1 Answer

Hello, what procedure must be followed to replace a bolt on Daewoo Lanos 2002 mteur dhoc 1.6. Thank you in advance, good day

Hello! Please tell me what you mean by replace a bolt? Are you asking for a particular torque specification?


I’m happy to help further over the phone at

Feb 09, 2011 | 2002 Daewoo Lanos

1 Answer

How do i remove cv joints from daewoo lanos 8/97 model

easy remove the hub assembly then cut the old rubber away then wipe it clean and in the back of the CV wher ethe shaft goes in their is a gap in the splines this is where the circlip is ,and its a pig of a job sometimes as the circlip has to opened whilst tapping the cv ,and its so full of that horrible black grease .

Jan 05, 2011 | Daewoo Lanos Cars & Trucks

1 Answer

How do you replace a clutch cable to a daewoo matiz

Hi, it must be done from underneath (unless you remove the entire engine), hoist up the car and work from underneath.
Drain Gear box oil.
Remove wheels, disconnect bolts and swing out wheel hubs, remove CV Joint drive shafts (both sides).
Disconnect two get change levers
Disconnect clutch cable.
Then replace it with the new one ...

Take care

Jul 27, 2010 | 2002 Daewoo Lanos

1 Answer


you have to remove strurt tower, if you mark the bolts before you remove you wont have to re-aling. then the rest is self explanatory

Apr 13, 2010 | 2002 Daewoo Lanos

1 Answer

Hi, I just did my MOT and servicing, my car failed the MOT because the CV gaiter split. Had it replaced and my car passed the MOT.. But then when I drove it back home, I smell burning rubber coming from my...

Not likely unless the CV gaiter (we call it a boot on this side of the pond) is really rubbing hard against something or is in contact with part of the exhaust system. When you had the gaiter replaced could they have left bits of the old one on the engine block or exhaust system. I'd look elsewhere for the cause of the burning smell.

Feb 20, 2010 | Nissan Minivan Cars & Trucks

1 Answer

Severe bearing noise from front wheel bearing/cv joint area.Cv joint still lubricated,I tend to think axle support bearing is dry & on the way out,but only assuming.How does front wheel bearing come out of...

you have to replace bearing and hub as a have to remove remove brakes and caliper rotor set them aside dont disconnect brake line. get a piece of clothes rack wire to hold brake caliper .do not let it hang by brake hose. you got to remove hub nut. best way to do that is loosen it a litttle while tire still on weight of car keep wheel from turning .

May 03, 2009 | 1999 Daewoo Lanos

1 Answer

Is this rumbling wheel bearings or transmission?

If the sound is all the time, no matter what you are doing then it is the Transmission going bad. CV Joints, Wheel bearing will only make the noise when in rotation.. Also remember that this is a front wheel drive car, so it will throw you off thinking it is the wheel bearings or CV joints due to the front wheel drive

Feb 15, 2009 | 2000 Daewoo Lanos

1 Answer

Cv shaft

did you replace any transmission fluid which may have leaked out during changing the shaft?

May 28, 2008 | 2000 Daewoo Lanos

Not finding what you are looking for?
1999 Daewoo Lanos Logo

178 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers


Level 3 Expert

85216 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

459 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides