Question about 1993 Jeep Grand Cherokee

1 Answer

Where is the carb on a jeep grand cherokee 1993 4.0 liter

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,826 Answers

There is no carburetor on any of the 6 cylinder or 8 cylinder Jeep Grand Cherokees. They have Fuel Injection and a throttle body which looks like a carburetor scaled down.

---
Instructions on how to remove and replace the throttle body follow:

Throttle Body REMOVAL & INSTALLATION

  1. Disconnect the negative battery cable.
  2. Remove the vacuum hoses from upper bonnet, unfasten the retaining clips and remove the upper bonnet assembly.
  3. Remove the lower bonnet retaining bolts and lower bonnet.
  4. Remove the throttle cable and the return spring.
  5. Disengage the wire harness connector from the injector.
  6. Disengage the wire harness connector from the WOT switch, ISA motor and TPS.
  7. Disconnect the fuel supply and return lines from the throttle body.
  8. Tag and disengage the vacuum hoses from the throttle body assembly.
  9. Disengage the potentiometer wire connector.
  10. Loosen throttle body retaining bolts and remove throttle body assembly from the intake manifold. To install:
  11. Clean the intake manifold and throttle body mating surfaces of old gasket material.
  12. Install a new gasket and the throttle body assembly. Tighten the mounting bolts to 16 ft. lbs. (21 Nm).
  13. Engage the potentiometer wire connector.
  14. Engage the vacuum hoses to the throttle body.
  15. Engage the fuel lines to the throttle body.
  16. Engage the WOT switch, ISA motor, TPS, and injector electrical connections.
  17. Install the return spring and throttle cable.
  18. Install the lower bonnet and fasten the retainers.
  19. Install the upper bonnet assembly, retaining clips and vacuum hoses.
  20. Connect the negative battery cable.
  21. Start the vehicle and check for fuel leaks. Fig. 1: Exploded view of the throttle body and related components where is the carb on a jeep grand cherokee 1993 - 86745g41.gif
next.gif

Posted on Aug 17, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What size is the bolt in the harmonic balancer in a 1993 jeep grand Cherokee larado 5.2 liter


i posted this yesterday
1-1/4" or 32mm
buy and use a caliper to measure bolts.

Dec 21, 2014 | 1993 Jeep Grand Cherokee

1 Answer

Are a 1993 4.0 liter high output 2 wheel drive Jeep Grand Cherokee countries have the same block as a 1990 Jeep Grand Cherokee Laredo 4 wheel drive it also has the 4.0 liter engine but it is not the high...


the first grand cherokee laredo was in 1992 . it was all jeep sports back then, the blocks are all the same .you will need to use some of the sensors from the old motor, the distributor and oil sending unit and temp sensor. will be no problem. if I can put a ford ranger motor in a mercury sable your swap is easier

Dec 05, 2012 | Cars & Trucks

1 Answer

Spark plug wire diagram


Check this for your 1993 Jeep Grand Cherokee 5.2 liter V-8 VIN "Y"


10_4_2011_3_34_41_pm.gif

If you need additional details, contact with the Jeep lovers.

Hope this helps; remember to rating this free answer.

Oct 02, 2011 | 1993 Jeep Grand Cherokee

1 Answer

My 1993 jeep grand cherokee v6 4.0 liter turns over but it will not start


The car cranks and turns over but will not start. Surely this seems that the fuel setting can be wrong , the valve timing. I suppose the fuel pump calibration and also the injectors and glow plugs must be checked.

Some tips on the link below;

http://www.fixya.com/cars/r5843031-tips_check_car_not_start

Apr 12, 2011 | 1993 Jeep Grand Cherokee

1 Answer

I need to see the firing order diagram for the 93 grand cherokee laredo 4.0.


Nice Jeep 1993 Jeep Grand Cherokee 4.0 liter L6 VIN "S"

zjlimited_293.gif


I have one 5.2L V8; good luck.

Apr 08, 2011 | 1993 Jeep Grand Cherokee

1 Answer

Need to know firing order for 93 v6 jeep cherokee


Nice SUV, Im owner '93 GC 5.2L V8 Magnum engine, so niceee!!!

1993 Jeep Grand Cherokee 2WD 4.0 liter L6 VIN "S"

d9de8af.gif

The next time, you need pay me 1 buck for each cyl. lol

TY for using Fixya (remember rated and comment this).

Sep 11, 2010 | 1993 Jeep Grand Cherokee

1 Answer

Vibration dampener removal.


it should be normal righty tighty, lefty loosey

Nov 19, 2008 | 1993 Jeep Grand Cherokee

Not finding what you are looking for?
1993 Jeep Grand Cherokee Logo

789 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...