Question about 2000 Ford Expedition
You should go to www.reliable-store.com they
have got books on every vehicle and also how to service/repair it,
service/repair/owner's/maintenance manual with
parts info, fuse box, gear box, torque specs,coiling, wiring diagrams, electrical diagrams, fuse diagrams, error codes, etc everything
Posted on Mar 15, 2018
I had the same problem. Reservoir would drain for no reason and I later found that the water was soaking the passenger side carpet and filling the wire channel under the doors. Tracked the problem to a barbed fitting behind the passenger side kick panel, just below the dash. The fitting connects the tubing coming through the firewall from the reservoir to the rear wiper/washer. The hose had come loose from the fitting (possibly due to freezing). I re-installed the tubing onto the the fitting and it has been fine ever since.
Posted on Feb 21, 2009
The gear box is a common problem on this model. That would be the place I would start. A cheap, temporary fix is to go to your local parts store and ask for Lucas Power Steering Stop-Leak. It will buy you some time.
Posted on Apr 10, 2009
Sorry im late with this,i couldnt seem to log on....The answer to your question is YES,there is a steel line under the intake with a short piece of rubber line attached to it and you can just about see it from the front of the intake with a light,it can leak and cause coolant to run off the back of the engine,The intake gasket set alone is about $40.00 and i dont know about the rubber line,i have seen it physically but havent changed one yet.Note the date of manufactor just incase,i bought an intake set for a 99 and the engine design was changed half way through...its not too hard to pull off the intake and re-install,you will need a 7mm socket for the coil packs,8mm socket for the fuel rail bolts and lower intake bolts and power steering bracket bolts and throttle bracket bolts,10mm socket for the intake bolts and alternator bolts and egr valve,and a large cresant wrench for the exhaust tube thats connected to the egr valve,flat screw driver for the air cleaner...and plenty of extensions with a swivel to be able to get to the back bolts of the intake....just incase you do it yourself this info could make it easier to gather tools.Its about a 3 1\2 to 4 hour job start to finish for the first time doing it,includes cleaning everything..Good luck
Posted on May 16, 2009
I almost got this. Does the fluid level go down ever few days with no leaking hoses,no leaking cooler if you have one and nothing coming out of the steering rack boots. It has to go somewhere. if it just comes out the cap the pump is not pulling it and sending it to the rack so you should not have much in the way of power steering. Did you put a new belt on wrong if posible and turn the pump backwards. Only other possibility is a flow blockage. Pull the return line,disable the ignition and crank engine. You should eventually pump fluid completely through the system and out the return line like it was headed back to the resevoir.
Posted on Sep 28, 2009
Testimonial: "Thanks, I will definately try that. I think it is probably flow blockage"
They don't make diagrams for brake lines. The lines are sold in bulk. You need to measure and duplicate the bends in the orignal lines and cut/flare the lines yourself. You will need a tubing cutter, flare tool and tubing bender.
Posted on Feb 27, 2010
Tips for a great answer:
Oct 05, 2014 | 2007 Chevrolet Impala LS Sedan New Cars
on Jan 23, 2010 | Dodge Grand Caravan Cars & Trucks
Dec 17, 2017 | 2005 Jeep Liberty
Dec 12, 2017 | 2005 Jeep Liberty
Mar 02, 2012 | 1996 Pontiac Grand Am
Feb 21, 2011 | 2003 Ford Explorer
Jun 22, 2009 | 2001 Saab 9-3
Mar 21, 2009 | 2001 Chevrolet Suburban
Feb 15, 2009 | 2001 Ford Expedition
Jul 25, 2008 | 2000 Jeep Grand Cherokee
70 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: