Question about 2001 Ford Taurus

2 Answers

Where do you find radiator filler. engine was streaming filled the coolant container but not sure if it took out enough water to fill radiator

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 157 Answers

If there is no filler neck on the rad. then there should be a mark to go by on the over flow tank the rad. will pull it out when it needs it

Posted on Dec 01, 2010

Ad

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,702 Answers

Most rads dont have a filler cap,,,,fill header tank and blead the engine water jaket from the blead screw on the top hose,

Posted on Dec 01, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How to add antifreeze 2002 dodge intrepid


Open the container of antifreeze. Using a separate EMPTY gallon-size container, pour out HALF of the contents into the empty container, making sure not to spill any. Now, FILL the newly filled container with tap water. Fill the rest of the antifreeze with water, also. Now, you are ready to add antifreeze to your vehicle! Simply locate the radiator cap, (Don't touch it if it's hot!!) and unscrew it. Pour the desired amount of your mixed antifreeze into the radiator. Remember not to do this without proper knowledge!

Jun 26, 2016 | Dodge Cars & Trucks

1 Answer

How do I bleed a 2002 Mazda Millennia coolant system


There is a spicket on the bottom left or bottom right of the radiator on some vehicles not sure about the millenia but you shouldn't have to bleed your coolest system. If you're looking to flush the radiator let the engine cool off, get a container big enough to catch all of the coolant about 2 or 3 gallons (for proper disposal) disconnect bottom radiator hose and drain into your container, you can flush with water through reservoir opening or heater core hoses (if you feel you have enough experience to do so through heater core) and to fill, reconnect bottom hose (I use 50-50 but I suggest you use what's recommended in your area) there is a cap that says something like do not remove without checking owners manual that looks like a smaller radiator cap on the left side front of your engine connected to a radiator hose. Remove this cap with engine cold and fill to top of opening, start the engine and continue to add coolest untill full and with engine running, replace cap. Fill your reservoir and you should be good to go.

Sep 14, 2015 | Mazda Cars & Trucks

1 Answer

Why is my thermo fan running comstantly at high speed ? Engine temp ect all good


I have heard of cases where there is enough coolant in the plastic bottle (reservoir) but, there is not enough coolant in the radiator itself. When the car is COLD (important - hot water and steam will burn you!!), remove the radiator cap and fill the radiator itself with coolant. In the COLD condition, remove the radiator cap, then start the car and while the engine is running, fill the radiator with coolant until the coolant is stagnant at the filler spout, then quickly replace the cap otherwise the engine will heat the coolant up and will start blowing out the top! If this doesn't fix the problem, replace your radiator cap and if that doesn't help either, replace the thermostat. Lastly but not likely, it might be a problem with the temperature sensor.

Apr 27, 2015 | Cars & Trucks

1 Answer

Air in lines for cooling system of 95 nissan maxima


Hello Michelle, my name is Michael and I too had air in the cooling system and this is how I got it out. I had to raise the front end to where the middle of the front bumper was about 40 inches. I removed the radiator cap and immediately had ton add more coolant till it was visibly full at the radiator filler neck. Make sure the cap on the overflow reservoir is on tight. Now start the car and observe the filler neck because you will probably have to add more coolant. once it is full turn on the heater to the max position and direct it to the feet and econ. you should see a lot of bubbles coming from the radiator filler neck. That is the air being purged from the system. make sure you fill with coolant as needed. Now when the t-stat opens you'll see the coolant drop from the filler neck because it's being exchanged from the engine block do not add coolant at this point. Put the radiator cap back on and remove the screw holding the overflow reservoir and raise the reservoir above the radiator and squeeze the tube to get the air out of the tube. Once the air is out and the tube is filled with coolant put the reservoir back in place and fill with coolant to the FULL mark. Shut off the engine lower vehicle and let the engine cool down and remove the radiator cap and fill with coolant till it is visibly full and replace the radiator cap. I had to do this twice but it worked and my car is operating at normal temperature and with the same stroke took care of a few other problems. Hope this helps and good luck to you.

Mar 29, 2013 | 1995 Nissan Maxima

1 Answer

I want to change coolant of mt car how to do it


Remove the radiator cap, open the drain valve at the bottom tank of the radiator, Drain the content into a container. Close the valve fill in the new coolant to the radiator up to about 20 mm below the rim of the filler. Run the engine to bleed out trapped air. Close the radiator and fill the coolant reservoir with the new coolant.

Oct 29, 2012 | Cars & Trucks

2 Answers

Looking for the fill plug on a 200 dodge darango 4 wheel drive front punkin all i see is a vent pipe


COOLANT-ADDING ADDITIONAL
Do not remove radiator cap to add coolant to system. When adding coolant to maintain correct level, do so at coolant reserve/overflow tank. Use a 50/50 mixture of ethylene glycol antifreeze containing Alugard 340-2 y and low mineral content water.
Remove radiator cap only for testing or when refilling system after service. Removing cap unnecessarily can cause loss of coolant and allow air to enter system, which produces corrosion.

COOLANT LEVEL CHECK
The cooling system is closed and designed to maintain coolant level to top of radiator.
WARNING: DO NOT OPEN RADIATOR DRAINCOCK WITH ENGINE RUNNING OR WHILE ENGINE IS HOT AND COOLING SYSTEM IS UNDER PRESSURE.
Remove radiator cap. The coolant level should be to top of radiator. If not, and if coolant level in coolant recovery bottle is at ADD mark, check for:
  • An air leak in coolant reserve/overflow tank or its hose
  • An air leak in radiator filler neck
  • Leak in pressure cap seal to radiator filler neck
TRANSMISSION and OIL LEVEL CHECK TUBES
pctech1_27.jpg

I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514

Mar 04, 2011 | 2000 Dodge Durango

1 Answer

1993 jeep grand cherokee havc code 06


Chrysler & Jeep Cooling System & HVAC Service: Every car make has its quirks, and Chrysler and Jeep vehicles are no exception. In researching this article, we found several examples of heater problems in these vehicles that seem to be fairly common.

On 2001 and 2002 Sebring Sedan, Sebring Convertible and Stratus Sedan, plus 1993 to 2002 Chrysler Concorde, LHS, New Yorker and 300M, Eagle Vision and Dodge Intrepid models with V6 engines, customers may complain their engine is overheating, or the heater is putting out little or no heat.

Chrysler Technical Service Bulletin 07-002-02 says the problem can be caused by a low coolant level in the cooling system. On these vehicles, air trapped inside the cooling system can displace coolant when the system is refilled. The radiator and coolant reservoir may appear to be full, but there still may be air inside the heater core and heater hoses. This will create a low coolant level that may lead to overheating and low heater output. The bulletin provides a special fill procedure to eliminate the trapped air so the cooling system can be completely filled.

The procedure goes as follows:
1. Obtain Chrysler special tool 8195 (Cooling System Filling Aid). The tool looks like a funnel and attaches onto the filler neck (just as a regular pressure cap does). But it also has a hose clip.
2. Attach the filling aid tool to the cooling system filler neck. Use the clip to pinch off the overflow hose attached to the fill neck. Attach a 4-6' long 1/4" ID clear hose to the bleed valve. Put the end of the hose into a clean container (to prevent coolant from spilling onto the accessory drive belts).
3. Open the cooling system air bleed valve before any coolant is added. If you do not do this, air can remain trapped inside the system and you won't get all the air out. On 1998 and later models with 2.7L engine, the valve is located on the water outlet connector at the front of the engine. On 3.2L and 3.5L engines, the valve is located on the lower intake manifold, left of center under the upper intake manifold. On 1993-'97 models with 3.3L and 3.5L engines, the valve is on the thermostat housing.
4. Pour a 50/50 mixture of coolant and water into the large side of the filling aid funnel. Use distilled, deionized or reverse-osmosis purified water, not ordinary tap water, which may contain salt or minerals that could contaminate the coolant.
5. Slowly fill the cooling system through the large side of the filling aid. Watch the hose connected to the bleed valve. When a steady stream of coolant comes out of the hose, close the bleed valve and continue filling to the top of the filling aid.
6. On 1993-'97 models, place a small, clean container below the end of the overflow hose. Then remove the clip from the overflow hose. Any excess coolant in the filling aid will now drain into the overflow section of the coolant bottle or into the container.
7. On 1993-'97 models, remove the reservoir and recycle the excess coolant.
8. Remove the filling aid from the fill neck. Make sure the filler neck and cap are clean, then replace the pressure cap on the coolant bottle.

Note: 1998 and later coolant bottles have two chambers. Coolant will normally only be in the inboard (smaller) of the two. The outboard chamber is only to recover coolant in the event of an overheat and should normally be empty - except for the coolant drained from the filling aid. This coolant will be drawn back into the pressurized side of the cooling system over time.

Hope helps.

Jan 12, 2011 | 1993 Jeep Grand Cherokee

2 Answers

How do i fill my reservoir and radiator


make sure the engine is cold, if you try to open the radiator cap while engine is hot you can get badly burned. get a container of coolant mixed with water, should be 50/50 mix. first open the radiator cap, which is at front of engine compartment near the center. roundish cap with 2 wings on sides. turn counterclockwise while pressing down to release cap. then fill to top with coolant mix. replace cap, turning clockwise till tight. then follow the small rubber hose from radiator cap area to the coolant resevoir. this container doesn't need to be filled completely, it has a full line. fill to that.

Feb 20, 2010 | 2003 Honda Civic

2 Answers

Water not circulating through engine


Does your engine overheat? Could be a thermostat that is stuck, let me know with some clarification and i can help ou better. Thanks

Dec 17, 2009 | 1998 Buick Century

2 Answers

How to change/flush coolant on a 2003 jetta


Slap on those vinyl gloves because the ethylene glycol in antifreeze can cause skin damage - however we recommend this because the antifreeze feels like engine oil.With your catch pan in place, remove the radiator drain plug and collect all old coolant. Immediately dispose of the coolant as required by environmental laws - if you are to surrender the old coolant at a waste management facility, be sure you use containers which can be properly sealed to avoid spillage, etc.To expedite the draining process, remove your radiator fill cap to allow air to enter the system.
Also be sure to remove all coolant from your radiator reservoir. We suggest you use the gravity siphon trick - just be sure not to ingest any coolant.
engine_coolant_04_thumb.jpg
[click for larger image]
figure 4
Watch the old coolant as it exits the system - this will give you a good idea of your vehicle's cooling system condition.If you see metal flakes, oily surface, white flakes, etc .. you can make a diagnosis of your engine's coolant system.
Essentially, if you see anything but coolant and some very minor debris, it can indicate the early signs of cooling system failure.When all coolant has been drained from the radiator, replace the radiator drain plug and then fill the system with plain tap water to dilute remaining antifreeze in the engine block.
With the cooling system refilled with tap water, replace the radiator fill cap and run the engine allowing it to reach operating temperature.When the engine's cooling fan turns on, it is an indication that the vehicle's thermostat has opened, allowing the freshly added water to circulate through the engine thus diluting the remaining coolant. Allow the engine to run for a few minutes before shutting it off.
At this point, you can either wait until the engine cools off, or take fate in your own hands and continue the flushing process.Repeat the draining process being sure to once again collect and dispose of all waste coolant.
At this point, if you have opted to purchase a radiator flush kit, you should refill the cooling system with tap water and add the caustic fluid as directed.
Run the engine for as long as the radiator flush kit calls for (usually less than 10 minutes).
engine_coolant_08_thumb.jpg
[click for larger image]
figure 8
Once again, drain the cooling system, collecting all waste fluid. This is the last time you will be required to collect engine coolant during this process.Now that the cooling system is empty, replace the radiator drain plug and refill the cooling system with distilled water only. The reason that you should only use distilled water at this point is to avoid mineral deposits which will deteriorate your cooling system over time.
Once the cooling system has been completely filled, start the engine to allow the water to circulate. Once again remove the radiator drain plug. As the engine runs, pour fresh distilled water into the radiator fill hole at the same rate that it exits the system.Continue this process until the water being drained from the radiator appears to be clear and free of debris. Once you are satisfied with the drain water's appearance, stop the engine and allow all remaining water to drain out.Replace the radiator drain plug and prepare to mix your distilled water and coolant.
Be sure to mix your coolant to the ratio recommended by your manufacturer. In most cases, the ratio is 50% distilled water and 50% coolant.
As a tip, mix the coolant and water in a third container being sure to observe the proper ratio.As you mix your water and coolant, use your hydrometer to measure the specific gravity - this will give you a good idea of whether or not you are mixing the coolant and water properly.
Once you have mixed enough coolant and water to fill your engine's coolant system entirely, grab a funnel and place it in the radiator fill hole.Fill your radiator at a rate of no more than:
{ 1 L/min. \ 1.1 US qt./min. \ 0.9 Imp. qt./min. }.
Continue the filling process until the coolant reaches the bottom of the fill neck. Now fill the radiator reservoir to the full mark.
With the radiator fill cap still off, start the car and allow it to idle. As the engine runs, continue to add coolant as air escapes the engine and cooling system.As you top up the radiator, be sure to "burp" the cooling system by firmly squeezing the radiator hoses (both upper and lower). Continue to squeeze and release the hoses to help push any errant air bubbles out of the system.
Once you are unable to fill the radiator any further, replace the radiator fill cap and stop the engine - you are finished.


Nov 15, 2009 | 2003 Volkswagen Jetta TDI

Not finding what you are looking for?
2001 Ford Taurus Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...