Question about 1992 Toyota Pickup

3 Answers

EFI fuse blows

My 1992 truck suddenly started blowing the 15A fuse. I had to jumper it to get home but then the 30A AM2 fuse blew. If I replace both the truck starts fine. If I put the truck into drive the 15A fuse blows almost instantly. The 30 A fuse blew about a mile down the road (15A jumpered). I don't think its the fuel pump but not sure. Any other ideas???

Posted by on

  • Anonymous Mar 27, 2014

    no spark



3 Answers

Check your O2 sensor wire. it hanging on your exhaust pipe.

Posted on Aug 20, 2008


  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 3 Answers

Grounding the vehicle.

Posted on Jul 06, 2008


  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 1,010 Answers

You have a short in one of your fuel injector wires. Check the wires from your fuel injectors for burns or cuts, look for bare wires grounding out on medal

Posted on Jul 01, 2008

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Amp fuse 30a keep blowing

You have possibly melted a couple of wires together along the radio circuit. Also the radio unit itself has 1 or more protection fuses actually inside the unit that have blown, usually at back of unit in little bay near the wire clusters.
Check your relays too, a blow out through jump starting can do all sorts of little burn-outs.

Oct 15, 2016 | 2006 Lexus Rx 330

2 Answers

88 toyota pick up v6 keeps blowing efi fuse

you may have a short of some kind, when a fuse blows repeatedly it is no good just replacing, you are being told that something is wrong with the equipment.
You will almost certainly have to visit a technician for a diagnosis. It is unlikely to be something that an inexperienced end user can sort out I am afraid.


Oct 26, 2015 | 1988 Toyota Pickup

1 Answer

Fuse blown during car running

Thats the EFI fuse ,it should be replace .Its a fuel cut fuse.

Feb 22, 2014 | 1998 Toyota Corolla

1 Answer

My power window and door locks fuse keeps blowing.

When the fuse blows figure out what you are doing, what switch is being pressed, then remove the needed panels to access the wiring to the switch and motor it operates, then you will find the damaged wiring and repair the short, no quick fix, just hard grunt work.

Mar 16, 2017 | 1996 Toyota 4Runner

1 Answer

Where to start looking for a short in a 1992 ford ranger. keeps blowing the fuse that runs the dash lights and the tail lights ..first it blew .i replaced .was fine till next night .turned on lights...

connector under the truck, near the trans
cannot remember specifics at this time but remember starting there every time one cam into the dealer with tail light issues and blown fuses

Jun 17, 2010 | 1992 Ford Ranger

1 Answer

I have a 1991 Toyota MR2 that will not start.

The EFI fuse is for fuel components, and for powering up the ecu. There is a lot on that circuitry. The 15 amp fuse, is also the power for the EFI relay. If this relay is without the power from that fuse, you probably won't have the fuel pump working, and the ecu won't be fully powered up.
Check the fuse again to see if it blew out again. If it did, you will have to trace the circuits for a short. Also, the EFI fuse gets power from the 40 amp AM2 fuse, so if the EFI fuse has power to it, the AM2 fuse is okay.
If I were you, I would test and check all fuses in all fuse/relay boxes under the hood. checking fuses is easy with a cheap test light. With the key in ON, every fuse on the car has power to it. So you clip tester light to ground (use neg. batt'y post), and then use test light probe into the little slot on the top end of a fuse. You do not have to take fuse out to visually inspect.
On the top end of all fuses are 2 little slots (one at each end of fuse) that is open to the metal strip inside. So you turn key to ON, then probe one end of the fuse. The test light should light up. Even a blown fuse will light up tester on one end of the fuse. Now to test the fuse itself, use the probe and touch into both ends of the fuse. A good fuse will light the tester on both ends of the fuse. A blown fuse will only light up one end of the fuse-the metal strip has blown so no power on both ends of the fuse, SEE?
And by using the test light, you also verify that power is getting to
the fuse. It is easy, and you are on the way to becoming an automotive electrician. Next, you need to buy and use a multi-meter, for automotive uses buy a digital volt-ohm meter (DVOM), which is what most multi-meters really are. And you don't have to buy an expensive one. I have a Sears Craftsman DVOM, about 20 years old, and it only cost like $30.

May 09, 2017 | 1991 Toyota MR2

1 Answer

1994 toyota corolla blowing AM2 30A fuse under the hood

On top of the cover of the fuses it will tell you what that fuse was for. Odds are whatever it is, is shorting out and will need to be replaced.

Dec 12, 2008 | 1994 Toyota Corolla

1 Answer

Keeps blowing 15a efi fuse 1991 toyota pickup 2.2 re

there's a short somewhere causing that amperage to go up

Dec 12, 2008 | 2004 Toyota Corolla

Not finding what you are looking for?
1992 Toyota Pickup Logo

666 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides