Question about Peugeot 405

1 Answer

Drawing required for 1997 peugeot 405 1.8 petrol with air-con serpentine drive belt, there are 6 pullies. N:B I do not require the cam belt drawing

Posted by on

  • adyson156 Dec 24, 2010

    to alicantecoli, you have responded to my Q re. the serpentine belt drawing 405 Peugeot. However you did not attach or send anything. Please help, its urgent

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Peugeot Master
  • 22,485 Answers

Drawing required for 1997 peugeot 405 1.8 petrol - alicantecoli_5.tifHope this helps

Posted on Dec 24, 2010

  • Colin Stickland
    Colin Stickland Dec 25, 2010

    sorry but it will come through as it has to be censored first and as its christmas ?? it might take a time ,pictures i have sent before are released as passed straight away but any new ones i do ??

×

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi I need to replace the serpentine belt on Hyundai tucson (2004) the problem is the air con pulls seems to have siezed, can I get a smaller belt as I don't really need air con in scotland. Cheers


my autodata belt book shows 18 hyundai belt set ups 1992 to2012 and only one that runs a special belt for the ac
for all the rest the ac pulley is required as the belt runs around it to drive power steering, alternator , water pump
test the ac pulley by removing the belt( after drawing a diagram of how it runs ) and trying to spin the pulley
if it is as you say have a mobile mechanic/ ac mechanic come and remove the pulley and replace the bearing ( about 1 1/2 hour and $20.00 for the bearing
if the pulley spins then disconnect the wire to the compressor so that the clutch is not engaged for the compressor

May 04, 2016 | Hyundai Cars & Trucks

2 Answers

Greetings for All I need Peugeot 405 Alternator/Power Steering Drive Belt diagram


a serp belt layout is what you require
is this your vehicles engine... if so
the tensioner needs to be moved and held so you can get the belt on
26179957-343vouaw2fo2jhrbxrgaiaqu-5-0.jpg

Apr 29, 2016 | Peugeot Cars & Trucks

1 Answer

How to change serpentine belt on 2006 buick lacrosse


Start by drawing a diagram of the belt routing. Serpentine belts normaly have 1 spring loaded tensioner (1 pully will have a nut or 3/8 or 1/2 inch drive hole) That will be the tensioner. get spanner or ratchet to fit & lever the tensioner away from the belt. Remove belt. fit new belt to most pullys except the easiest to get to, lever the tenioner back & fit the belt to the last pully, Check the belt is on all pullys properly & your done

Jun 28, 2012 | Cars & Trucks

1 Answer

Anyone got a peogeot 405 1997 1.8 petrol drive belt routing drawing please?


I found a drawing that may help you. Let me know if it does.

The website is: http://www.autodata.ru/efisakh/melochi_9.htm
moz-screenshot.png
Scroll down to the bottom of the page and it has your Peogeot belt drawing.

Hope this helps

Dec 23, 2010 | 1991 Peugeot 405

1 Answer

How to replace serpentine belt on a car


1. Make a drawing of the routing of the existing belt before you take it off, or there may be one on the fan shroud or nearby. 2. Locate the spring loaded tensioner. It will be a pully that is not connected to any other component. 3. You will need a long braker bar (most likely half inch drive). On the spring loaded tensioner you will find a place (a cut out square) to insert the braker bar. (Note, no socket is needed, just the braker bar itself) This is a secure way to leverage the tensioner 4. Using the braker bar, move the tensioner to release tension on belt. 5. Slide old belt off pulleys, and move around fan. 6. Install new belt with same method, making sure the routing is correct.

Oct 31, 2010 | 1997 Chrysler Sebring

1 Answer

I get noise from the pulling system when i turn the heater on


hi,

you may get some noise from the pullies to some degree, when you switch your heater and/or defroster on the heater fan draws major amps and the defroster secretly turns the air conditioner on to defog the windows, so thats two major things drawing off the pullies. have you had your serpentine belt serviced ever? it may be time for a new serpentine belt? It could also mean your serpentine idler pully bearings may be getting ready to go, the alternator may be getting ready to buy acreage also. watch your gauges closely when your driving. your car is getting ready to have one of these accessories go out, dont take it on long trips and take it to your mechanic if it gets any worse. clean your battery posts in the meantime also..

jm

jm

Nov 29, 2009 | 2002 Chrysler Town & Country

1 Answer

How to tighten my 306 dt 98 fan belt


you need to take off the drivers front wheel and plastic cover infront of the engine.
then you need to crack off two allen key type bolts holding the braket and tensioner pully in place, that is positioned just right of the crankshaft pully. Once the whole unit is slack you have to loosen the adjuster that is visible underneath the tensioner braket to take the tension off the belt. Once the belt is loose enough take it off and reverse process avoiding overtightening new belt. [It needs a little give to avoid damging bearings in the pully]

Sep 01, 2009 | 1990 Peugeot 405

1 Answer

Pug 405 serpentine belt with air con 1996 xrdt


you cant remember how work the run out ?? or how to adjust the adjuster

Feb 26, 2009 | 1991 Peugeot 405

1 Answer

Engine fires but wont start


check the crank sensor or the cam sensor behind the pully,s to make sure there plugged in.

Dec 18, 2008 | 1991 Peugeot 405

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

scj103

Level 2 Expert

104 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...