Question about kawasaki GPZ 500 S - GPX 500 R Motorcycles

1 Answer

Motorbike wont move

My bike wont move? it revs and idles fine but as soon as i click it into gear and start to release the clutch it cuts out, no matter how many revs i give it. ive cleaned the carb, both spark plugs have been changed along with the oil, both spark plugs are sparking well so now i dont know what else i can try. it has been running but the past week its just done this, it back fires more now but i think thats just because i may be flooding it when it cuts out all the time and i re start it up.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 413 Answers

Sidestand lockout switch is sticking...bike thinks that you're trying to ride away with the stand down so it kills the sparks.

Posted on Mar 26, 2013

Ad

3 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

tombones

  • 3567 Answers

SOURCE: kawasaki 300 bayou won't rev up.

No guarantees but try this. Pull the slide from the throat of the carb. Now move the clip on the jet needle down one notch. This will richen the low end mix. Two notches may be needed but do one notch at the start.

Posted on Apr 30, 2009

Anonymous

  • 2 Answers

SOURCE: FXR suzuki 150 will idle but wont rev

Clean the fuel tank, fuel hose and fuel valve.

Posted on May 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

REPLACED CLUTCH ON ZR 550 CLUTCH ENGAGES , BUT WHEN FULLY RELEASED BIKE JUDDERS THEN STALLS OUT . TRY TO ADJUST & GEARS WONT ENGAGE .


So if you raise the revs to say about 4000 rpm and let the clutch out does it stall or judder or both will it engage at all and pull away ?

Mar 07, 2015 | Motorcycles

1 Answer

Why wont my Flymo qs 46sd rev ?


does it have a throttle cable fitted?? you really dont need an idle as as soon as you release the opc or dead mans handle it will cut out anyway. engine should be reving at 3000-3100 rpm. if this mower has a briggs and stratton engine fitted, remove the air filter and check the spring and linkege is still attached to the air vane govenor

May 20, 2014 | Garden

1 Answer

2002 Kawasaki ZX-6R is stalling when the clutch is disengaged


Hi, Jesse the ignition circuit cut-off system comprising of the side stand switch, clutch switch and neutral switch has the following functions:
a. It prevents starting when the transmission is in gear and the side stand is up, but the clutch lever is not pulled.
b. It prevents starting when the transmission is in gear and the clutch lever is pulled, but the side stand is still down.
c. It cuts the running engine when the transmission is in gear and the side stand is moved down.
Periodically check the operation of the ignition circuit cut-off system according to the following tests.
With the engine turned off:
1. Move the side stand down.
2. Make sure that the engine stop switch is set to "RUN"
3. Turn the key to "ON".
4. Shift the transmission into the neutral position.
5. Push the start switch if the engine does not start the neutral switch may be faulty.
With the engine still running:
6. Move the side stand up.
7. Keep the clutch lever pulled.
8. Shift the transmission into gear.
9. Move the side stand down if the engine does not stall you may have a faulty side stand switch.
After the engine has stalled:
10. Move the side stand up.
11. Keep the clutch lever pulled.
12. Push the start switch if the engine does not start you may have a faulty clutch switch.
This check is most reliable if performed with a warmed-up engine.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Bike stalls when clutch is disengaged
zx6r 05 when put in gear engine stalls
Kawasaki 2000 Ninja ZX 6R Service Manual
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Nov 03, 2017 | 2002 kawasaki ZX-6R

1 Answer

1999 Kawasaki VN 750 Vulcan the bike dies when releasing the clutch lever


Hi, Dustin the ignition circuit cut-off system comprising of the side stand switch, clutch switch and neutral switch has the following functions:
a. It prevents starting when the transmission is in gear and the side stand is up, but the clutch lever is not pulled.
b. It prevents starting when the transmission is in gear and the clutch lever is pulled, but the side stand is still down.
c. It cuts the running engine when the transmission is in gear and the side stand is moved down.
Periodically check the operation of the ignition circuit cut-off system according to the following tests.
With the engine turned off:
1. Move the side stand down.
2. Make sure that the engine stop switch is set to "RUN"
3. Turn the key to "ON".
4. Shift the transmission into the neutral position.
5. Push the start switch if the engine does not start the neutral switch may be faulty.
With the engine still running:
6. Move the side stand up.
7. Keep the clutch lever pulled.
8. Shift the transmission into gear.
9. Move the side stand down if the engine does not stall you may have a faulty side stand switch.
After the engine has stalled:
10. Move the side stand up.
11. Keep the clutch lever pulled.
12. Push the start switch if the engine does not start you may have a faulty clutch switch.
This check is most reliable if performed with a warmed-up engine.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Clutch kill switch Kawasaki Vulcan 750 Forum Kawasaki VN750 Forums
bike dies when releasing the clutch
Kawasaki VN 750 Service Manual
OEM Parts for Kawasaki
1999 Kawasaki Vulcan 750 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Jun 09, 2012 | 1999 kawasaki VN 750 Vulcan

1 Answer

1999 Kawasaki Voyager XII dies when the clutch lever released


Hi, David the ignition circuit cut-off system comprising of the side stand switch, clutch switch and neutral switch has the following functions:
a. It prevents starting when the transmission is in gear and the side stand is up, but the clutch lever is not pulled.
b. It prevents starting when the transmission is in gear and the clutch lever is pulled, but the side stand is still down.
c. It cuts the running engine when the transmission is in gear and the side stand is moved down.
Periodically check the operation of the ignition circuit cut-off system according to the following tests.
With the engine turned off:
1. Move the side stand down.
2. Make sure that the engine stop switch is set to "RUN"
3. Turn the key to "ON".
4. Shift the transmission into the neutral position.
5. Push the start switch if the engine does not start the neutral switch may be faulty.
With the engine still running:
6. Move the side stand up.
7. Keep the clutch lever pulled.
8. Shift the transmission into gear.
9. Move the side stand down if the engine does not stall you may have a faulty side stand switch.
After the engine has stalled:
10. Move the side stand up.
11. Keep the clutch lever pulled.
12. Push the start switch if the engine does not start you may have a faulty clutch switch.
This check is most reliable if performed with a warmed-up engine.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Bike dies as soon as clutch is released in first motorcycles
engine dies when let out clutch in gear Kawasaki Vulcan Forum Vulcan Forums
Kawasaki Voyager XII Service Manual
OEM Parts for Kawasaki
1989 Kawasaki Voyager XII Owner Manual

May 29, 2011 | kawasaki Motorcycles

1 Answer

The bike will crank up and idle and I can thottle it up fine but as soon as i put it in gear and release the clutch it dies.


is the kickstand still down when you are doing this. Some bikes have a kickstand sensor and wont let it run when down.

May 18, 2011 | 2002 kawasaki EN 500 Vulcan Classic

1 Answer

Kdx 200 clutch not engaging properly


The clutch in your bike is a wet clutch. There is a lot of hyrdostatic friction even when the clutch is released completely. I think a large factor is the type, age and condition of oil. Perhaps something as simple as an oil change would help.

Jan 14, 2010 | 2005 kawasaki KDX 200

1 Answer

Bike stalls if moved


check carb for bent needel or any other damage

Oct 10, 2009 | 2004 Vento Rebellian

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

164 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5971 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

ROB

Level 3 Expert

858 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...