Question about Motorcycles

Open Question

How do iget the cover off to change the battery charger this is the cover that covers the unit that is under the seat

Posted by on

  • Gregg Mahin
    Gregg Mahin Oct 06, 2017

    Hi, Waymon I would really love to help you with your bike question but due to the magnitude of yesterday's solar flare the batteries in my crystal ball are dead and my mental telepathy headset circuitry was melted. I need the year, make, and model of your motorcycle please click on the word "COMMENT" below and provide this information in the box that will open and then click on the green comment box in the bottom right-hand corner after it posts I will receive an "ALERT" icon that will allow me to respond to your information. Good luck and have a wonderful day.



6 Suggested Answers


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017



  • 243 Answers

SOURCE: Fusabl iink on Positive battery terminal??? how to change it >>

There should be two small 8mm bolts holding the fusible link by the sides...don't pull the fusible link before unscrewing the 2 bolts as they will damage the holder.

Posted on Oct 29, 2008



  • 1 Answer

SOURCE: jane powertwin has stains on seats do covers come off for washing

I normaly Scrub the seats down with some stain remover and hot water on a sunny day, or ona day when it is dry. Then leave them to dry, and they come up pretty good.They only detach from the pram as a full seat so not able to put in a washer.

Posted on Jan 14, 2009


  • 1 Answer

SOURCE: dismantleing canopy

If this is for the Graco Snugride (I have the Windsor model from the Quattro Travel System), this will work:

1. Push the Graco canopy to one side, exposing the plastic support bars that hold the canopy in place.

2. The center of the support is where the canopy comes apart. Using both hands, pull the canopy support
bar apart (as if you were playing tug-of-war). It's best to grab the curved ends and pull HARD (and point it away to the side so that you don't hit your face).

3. Once the support bars are apart, remove the old Graco canopy and slip on the new/freshly washed canopy.

4. Secure the support bars by snapping them shut, and then slide the canopy into place.

Posted on Feb 07, 2009


  • 1 Answer

SOURCE: fitting rear seat covers to AU Ford Falcon

To remove the rear seat off an au falcon get in the rear of the car facing the opposite way to which you drive facing the rear seat. you need to slide your hands along down where the seat belt conectors are pulling it up abit. than you need to use quite a bit off force pulling it towards your self.

Posted on Nov 08, 2009


  • 1 Answer

SOURCE: how to change seat covers on a quinny buzz stroller

Try this link
The instructions & diagram are in section 6.2 on page 5 of this 7 page pdf document.
Hope it helps!

Posted on Nov 25, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Battery needs charging

Try looking under the seat or behind one of the side covers. A standard 12 volt automotive battery charger should do the trick.

Nov 18, 2013 | Honda XR 125 L Motorcycles

1 Answer

I would like to know how to change the battery in a 2008 r350 Mercedes

Try this To get to it is complicated

Move seat as far back as possible. Seat rails have covers on them - slide them forward....the left one will only slide forward, cannot be removed. Between the two seat rails you will see two little battery cover mounting nuts. Use 6 mm T-handle hex key to remove the nuts. Move seat as far forward as possible and twist rear rail covers to left and right and then pull toward rear of car. Pull back/fold floor carpet under seat from front to back (carpet is perforated so you may have to really yank the first time). There are two more battery cover mounting nuts between rear seat rails. There is a battery cover with an air vent pull it slightly to right and then lift out. There is a vent hose attached to battery on left side -- pull it out. Unfasten & remove attachment nuts on left side (low). Remove the battery attachment once those nuts are off. Push battery to the left. Disconnect battery negative lead (right) (do not let it touch pos. lead on left). Remove cover from pos (red/left) terminal and disconnect lead.

Aug 28, 2012 | 2008 Mercedes-Benz Mercedes Benz R Class

1 Answer

How do I get to the battery to charge it

To access your battery, take off your side covers. There is a bolt on each side of the back of the seat. Remove the two seat mount bolts and lift the seat off to access the battery. If you only want to charge the battery take off the left side cover, attach you power cable from the charger to the plus cable going from the battery to the starter solenoid. Then, attach the negative charger clamp to a frame bolt or engine mounting bolt. This will charge your battery with out removing the seat.

Jul 10, 2011 | 1994 Honda VF 750 C Magna

1 Answer

How do i connect a trickle charger to my 1150rt

Access to your battery is likely under your seat. Remove the one or two bolts that hold the rear of the seat to the motorcycle and lift. When you find the battery, remove the cover, if any. Connect the red lead from the charger to the + post of the battery and the black lead from the charger to the - post of the battery. I wouldn't use anymore than a 2 amp regulated charger for this and I would not keep it on indefinitely. Couple days on ... couple days off is what I would do.

Thanks for your query @

Feb 28, 2011 | 2004 BMW R 1150 RT (ABS)

1 Answer

How do I change the battery on my VTX? I am going to replace my battery with a new one, what is the proper proceddure to do this?

Depending on your model of vtx1300 there are 2 or 3 bolts holding the seat on. On the S model remove the side covers and remove the 2 bolts(one on each side) and lift off the seat . On the C model there is a nut at the rear of the seat that also has to come off. Lift the back of the seat and pull it toward the rear of the bike. Remove the three bolts on the plastic cover and the two cable bolts. The battery will lift straight up out of the battery box. Be sure to charge your old battery with a 12 volt charger before storing. If installing a new battery be sure to use your charger to bring the new battery up to a full charge before using it.

Dec 03, 2010 | 2004 Honda VTX 1300

1 Answer

Replace batteries

Hi. To remove the batteries, it is neccessary to remove the seat first. Turn the seat a bit and then lift it straight up. Next remove the cover under the seat, it will probably be held on with velcro. Under the cover you will see the batteries. They will be held in place by fabric straps, which you will have to loosen. Make sure that the machine is turned off, unplub the batteries and remove them.
You will be the best judge of the condition of your batteries.
Can you travel as far as you used to, without the battery gauge falling further than it used to?
It is important to recharge your batteries after each trip, and to charge them overnight at least.If you haven't used the machine for a few weeks, give it a charge overnight.
Some chargers can be left on for weeks at a time, and some chargers should only be used overnight only. The reason for this is that some chargers, such as the Invacare 8 amp charger, will drop down to a float charge after charging the batteries. Most of the smaller 4 amp chargers do not drop down to a float charge, but maintain the full voltage untill they are turned of.
Good luck. Neil.

May 31, 2010 | Pride Mobility Products Celebrity X - 3...

1 Answer

How do i get the seat off so i can charge the battery?

There should be a keyhole above LH cover, insert ignition key or if saddle style, grab widest seat corner to expose 2 bolts, remove bolts and pull seat out.T install reverse the process. As battery is a MF unit, you need a special battery charger to charge it, if it is old (>3years) better get a new battery. Good?

Apr 15, 2010 | 1997 Yamaha YZF Thunder ace 1000 R

1 Answer

Change Batteries in Pronto M91 with swivel seat.

Turned out to be a "doh!" moment. Use the lever on the side of the seat to permit swivel. Unplug Controls connector. Lift seat off unit. Remove battery compartment cover by loosening 2 Philips-head screws on the Charger cover at the rear. Disconnect cable to Electronic Controller at front of front battery. Disconnect the Red and Black battery connectors, the ones that join the 2 batteries. Lift out batteries. Transfer battery connections to new batteries. Reverse the above process to reassemble.
Solved this without any help from outsiders, including FixYa, who wanted to charge me for the solution.

Jun 12, 2009 | Invacare Supply Group Invacare Pronto M91...

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6103 Answers


Level 3 Expert

85223 Answers

richard libby

Level 2 Expert

209 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides