Question about Ultra Motorcycles

1 Answer

2006 ultra clASSIC HOW DO YOU PHYSICALLY REMOVE BATTERY I CANNOT GET MY HANDS AROUND BATTERY IN ORDER TO PULL IT UP AND OUT

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,633 Answers

There is a strap available that clamps to the battery posts.. you could buy one of them.. or, you could work a strap or rope down under the battery and pull it up by that.

Posted on Jun 03, 2018

Ad

5 Suggested Answers

Mitchy123

Mel Jacobson

  • 216 Answers

SOURCE: how to remove starter from ultra classic. engine

Yes, The first thing you do is disconnect the battery ,,,Harley says to pr3vent accidental starts, but if you dont, your going to short something out..... You are going to have to remove the outer primary to get to the jackshaft. Disassemble and pull the jackshaft then you can unbolt and remove the starter ,,,,,

Posted on Apr 18, 2009

Ad

Anonymous

  • 80 Answers

SOURCE: removing harley davidson ultra classic gas tank

Drain the fuel either by siphening or removing the cross over tube at the front of the tank and letting it drain that way or just block off those cross over lines and leave the fule in the tank for removal.

0) remove seat
1) drain fuel
2) undo cross over line (bottom front of gas tank.
3) shut off pet **** and remove fuel line from pet ****.
4)there should only be 2 bolts holding the tank on, one at the top front of the tank and one at the back of the tank.

All in all a pretty easy (but possibloy messy) job.

Posted on Jun 06, 2009

ollie reece

ollie reece-jones

  • 1167 Answers

SOURCE: starter removal on 2004 ultra classic harley davidson

Disconnect battery , remove the outer primary case, pull back the lock tab on the starter jackshaft, unbolt the retainer screw, then remove the two starter bolts from the right side, sometimes you need to loosen the oil tank mounts to get at these, slip the starter and coupler out as a unit, replace the coupler and jackshaft the same way they came out when the new starter goes in, install bolts , retighten the jackshaft bolt and bend over the retainer, install and fill primary case, connect battery thats it buddy

Posted on Oct 12, 2009

Anonymous

  • 60 Answers

SOURCE: O2 ULTRA CLASSIC STARTER JUST CLICKS AND BATTERY

check the solenoid on the starter. and all of the connections.

Posted on Oct 13, 2009

ironcrossaud

Iron Cross Audio

  • 281 Answers

SOURCE: I have a 2006 Ultra Classic, Washed it Saturday

06 radios did not have enough liquid protection on the faceplate PCB. The radio will need to be repaired. Contact Iron Cross Audio for repair options.
www.ironcrossaudio.com

Posted on May 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the signal flasher located on an 03 ultra classic


On an 03 bagger it will be under the seat. You'll have to remove it. Under the seat is the battery you should see a little silver clip towards the back ledge of the battery tray. That's the turn signal module. Remove the clip and pull the unit up amd out.

Jan 08, 2015 | 2003 Harley Davidson FLHTCUI Electra Glide...

1 Answer

How to you remove the starter from a 2002 harley ultra classic


Pull MAXI fuse or disconnect battery.Drain primary, then remove primary cover, remove bolt from jack shaft on starter and pull of gear. On the other side remove the two 1/4 alan bolts holding starter on and of course remove starter wire.You will have to replace the seal after.

Aug 20, 2013 | 2002 Harley Davidson FLHTCUI Electra Glide...

1 Answer

Removal of an 06 ultra classic trans


This removal requires some special tools and a manual. First remove the negative battery cable.Drain and remove primary cover. Remove the shift shaft from the housing.Remove the primary drive. The clutch nut has left-hand threads so righty loosey. Remove the small screw on the end of the starter gear shaft. Remove the screws holding the inner primary housing. Now on the right side. Remove the exhaust. Remove the two screws holding the starter motor to the trans housing. Inner primary will now come off. There is a race that is pressed onto the mainshaft that requires a special puller to remove. Drain trans fluid. Remove trans side cover, the one with the clutch cable. Remove the trans top cover. Remove the shifter drum. Remove the shift fork shaft through the right side of the trans bearing door. Remove the shift forks through the top off the trans housing noting location. Remove the screws that hold the bearing door to the case. There are a couple of pry points that you would use to separate the door from the case. Should come on out after all that.

May 15, 2012 | 2006 Harley Davidson FLHTCUI Ultra Classic...

1 Answer

Remove the outer fairing on 2006 ultra classic SE


Hi Anonymous, for more information about your question please visit the websites below. Good luck and have nice day.
Remove and install Harley Davidson Touring outer front fairing Law Abiding...

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Mar 31, 2012 | 2006 Harley Davidson FLHTCUI Ultra Classic...

1 Answer

How do I remove the wrap around lights on an 06 Ultra Tour Pack?


Hi Anonymous, if you remove the tour pak liner this will give you access to all light fasteners. Good luck and have nice day.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Jan 09, 2012 | 2006 Harley Davidson FLHTCUI Ultra Classic...

1 Answer

I just pulled my 2006 screaming eagle ultra classic out of winter storage and it won't start. The battery had a full charge and it makes a long clicking sound when I try to start it. It's the...


Harleys pull a lot of amps starting,, Just because the battery says 12v doesn't mean the charge is handling the draw when trying to start them ,, get the battery LOAD checked,, remember also,, Harley's are known for drawing Juice when starting , thats why any dealer or shop will tell you that if you start one be sure and drive it a while,, start and stop trips eat up the battery since the alt won't keep up with the charging. when I leave mine for any time, I use one of the trickle charge units just to keep it at full

May 13, 2011 | 2006 Harley Davidson FLHTCUSE Screamin...

1 Answer

I have a 2005 harley davidson electra glide standard and need to get to the battery. Where is the release?


In order to get to the battery on your touring model Harley you need to
first open your tour pack (if you have one)
at the back of your passenger seat the is a Philips head screw with a star washer under it.
with a long (but not too long) #2 Phillips screw driver remove the screw and place it where you can not lose it (be sure not to scratch your tour pack)
while standing on the low side of the bike or right side place your left hand over the seat tab (where the screw cam out of) and your right hand at the nose of the seat pull slightly to the back of the motorcycle until the front tab has been released from the bike.
then push the nose of the seat to the high side of the bike still keeping your left hand completely over the rear seat tab so that now you don't scratch the rear fender and push a little forward and shimmy back the seat strap with your right hand ( this step is a slight pain in the but)
one the seat has been removed you then can access your battery.
in order to remove you need some really good finger strength or a battery removal tool.
on the high side just over the battery is a Torx #45 self tapping screw head holding a small bracket in turn holding the battery in place. remove that and first with a 10mm wrench remove the negative battery terminal and then remove the positive to keep from throwing parks.

Dec 19, 2010 | 2005 Harley Davidson FLHTCUI Electra Glide...

1 Answer

Starter removal on 2004 ultra classic harley davidson


Disconnect battery , remove the outer primary case, pull back the lock tab on the starter jackshaft, unbolt the retainer screw, then remove the two starter bolts from the right side, sometimes you need to loosen the oil tank mounts to get at these, slip the starter and coupler out as a unit, replace the coupler and jackshaft the same way they came out when the new starter goes in, install bolts , retighten the jackshaft bolt and bend over the retainer, install and fill primary case, connect battery thats it buddy

Oct 12, 2009 | 2004 Harley Davidson FLHTCUI Electra Glide...

3 Answers

How to remove starter from ultra classic. engine in frame with exhaust hooked up.engine still assembled. will the primary have to be removed. battery disconnected.


Yes, The first thing you do is disconnect the battery ,,,Harley says to pr3vent accidental starts, but if you dont, your going to short something out..... You are going to have to remove the outer primary to get to the jackshaft. Disassemble and pull the jackshaft then you can unbolt and remove the starter ,,,,,

Apr 17, 2009 | 2000 Harley Davidson FLHTCUI Electra Glide...

3 Answers

Cant find the battery


Under the tour pak on the rear fender is a screw which you have to remove then you can lift the seat out from the rear end. When replacing the battery wrap a thin strap of leather or canvas around the battery and this will allow you to lift the battery out a lot easier the next time.

Feb 15, 2009 | 2000 Harley Davidson FLHTCUI Electra Glide...

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ultra Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Lawrence Oravetz

Level 3 Expert

10543 Answers

Brad Brown

Level 3 Expert

18166 Answers

Are you an Ultra Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...