Question about 2001 Yamaha V Star 1100 Classic

1 Answer

How to remove and replace the oil filter - 2001 Yamaha V Star 1100 Classic

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,230 Answers

Hi there,

Well you can follow the below steps -
Tools needed - 
6, 8 and 10mm Allen (hex) key 3/8" sockets or "T" wrenches
Socket wrench (3/8") and a 2" & 10" extension
12, 14 & 17mm. sockets
8 and 17mm short box wrenches
Funnel
Shallow oil drain pan.
Short section of a 2"x4" piece of wood. About 4" long will do.

Supplies needed - 
Oil - 4 Quarts of MC specific oil (your choice) 
Oil filter - Yamaha 4X7-13440-90
Wipe rags & Paper towels
A 10" square of aluminum foil paper towels

1. ) With your bike in gear, place the short piece of 2\"x4\" under your side stand. The small block of wood positions the bike in more of an upright attitude. This will give you a bit of working room under the bike, but it will not raise it to the point of going over in the other direction.

2. ) Locate and lightly loosen the following bolts and nuts:
The oil drain plug - With the 17mm. socket wrench, Break loose the oil drain plug, but do not unscrew it (make sure that you have not loosened it to the point where the oil starts to seep out. (The silver colored bolt on the underside of the case, on the left side of the bike under the shifter)
The two nuts holding the forward exhaust pipe to the exhaust manifold with a 12mm socket wrench (Just break them free, do not remove them)

3. ) Take the bike out of gear. Remove the block of wood from under the side stand and warm the engine up by starting it and letting it idle for a few minutes. Then shut it down.

4. ) Put the bike back in gear and place the wood block back under the side stand. Slide the shallow oil drain pan under the engine and back out the oil drain bolt using either the 17mm short box wrench or the 17mm. socket wrench, so that you can unscrew it the rest of the way and remove it with your fingers. Clean the drain bolt with a rag and put it aside.

5. ) Using the 10mm hex socket, remove the two bolt holding the mufflers to the frame. Next, loosen the clamps holding the front pipes to the mufflers using the 6mm hex socket. Using the wipe rags (HOT!), pull the mufflers toward the back of the bike. They should slide right out.

6. ) (This step is only required if you have an 1100 Classic with floorboards) Using the 14mm socket and wrench, loosen the two bolts holding the right floorboard until they are almost completely out, and the floorboard will hang down slightly.

7. ) Next, using the 8 mm wrench, remove the bolt holding the rear brake reservoir. Let the unit hang loose.

8. ) Using the 12mm socket, remove the two nuts on the forward exhaust pipe flange. Grabbing the front of the pipe with wipe rags, gently remove the front exhaust pipe. Take extreme care in removing the pipe as you will scratch it (like the dealer's shop always does) if you are not careful. If the copper gasket falls off the engine, just let it go. I promise you that it will be very, very HOT! Just make sure that it goes back on when you re-assemble the pipes.

9. ) Using the 8mm hex socket with the 10 in. extension (or an 8mm. \"T\" wrench) loosen the five case screws holding the filter cover. There are 3 different lengths of screws, so leave them in the cover. You don't need to remove the 3 screws holding the round \"Yamaha beauty\" cover on the filter cover, there is nothing behind this cover (It comes off easily to enable you to buy a new one from the Star Catalog for $39.95 STR-5KS27-43-02 that does not say Yamaha). Remove the filter cover. If you wrap a small square of aluminum foil over the section of frame and wiring just below the filter cover, you will avoid slopping oil over the frame of your bike.

10. ) You will find an unpolished filter hatch plug underneath which you will need to wiggle back and forth as you pull straight out to remove it. Be careful not to damage the O-rings on the cover. Wipe any grit or dirt away with a clean paper towel.

11. ) Remove the filter (pay attention to the orientation of the filter when you remove it). Wipe any sediment from the filter chamber with a clean paper towel and insert the new filter.

12. ) Reinstall all parts in the reverse order of disassembly

13. ) Unscrew the black plastic oil filler cap and insert the funnel into the filler hole. Engine Oil with oil filter replacement (3.28 US qt) ( 0.28 quart = 8.96 oz ) Engine Oil- Without oil filter replacement 
(3.17 US qt) ( 0.17quart = 5.44oz )  

Start the bike and bring it up to full operating temperature. Check for any signs of leaking oil from the filter hatch and the drain plug.

When you shut the engine down, check your oil level in the sight glass on the left side lower engine case. The bike must be held level front to back and side to side. This is quite a balancing act as your head needs to be about 14" off the ground in order to see the oil level in the sight glass. Post comments for further help or information.........

Good Luck!!

Posted on Mar 27, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change the oil


1.prepare materials needed such as:
  • An allen wrench or screwdriver (for fairing removal, if necessary.)
  • An oil filter wrench (for removing the oil filter.)
  • The appropriate crush washer for your oil drain plug-- this can be purchased from a hardware store or motorcycle service shop.
  • A pair of needle-nose pliers, in case the oil filler cap is hard to reach or tightly screwed on.
  • An adjustable socket wrench.
  • Clean rags.
  • The proper amount of manufacturer-recommended engine oil.
  • A new, manufacturer-approved oil filter.
  • A funnel
2. Unscrew the oil filter caps 3. Remove the oil rain plug 4. Replace and remove the crush washer 5. Clean the oil drain plug 6. Remove the oil filter 7. remove and clean plastic mesh filter 8. Lubricate the O-ring of the new filter and attach it to the engine 9. Replace Oil drain plug and plastic mesh filter then pour oil 10. Check oil level

Jun 14, 2010 | 1983 Honda XL 125 R

1 Answer

How do i change the oil on my 01 vw gti vr6


This engine requires synthetic oil, 5 quarts, and oil filter. Remove dip stick, remove oil drain plug at bottom of engine oil pan, remove filter housing, remove oilf filter and o-ring. Replace o-ring and filter, rub o-ring with some new oil, replace filter housing, replace oil drain plug, pour new oil in at top of engine oil cap, replace dip stick, start engine, run for 45 seconds, turn off, check dip stick to make sure oil is at correct level. You are done, recycle old oil.

Sep 19, 2009 | 2002 Volkswagen GTI

1 Answer

Oil filter


To change your oil filter, remove oil drain plug, drain oil into an oil pan, clean and replace oil drain plug, then remove oil filter, pour a drop of clean oil onto a new oil filter, and lube gasket, then replace the old oil filter with the new oil filter. Finally, add clean oil to the motorcycle until the oil level window shows oil in the middle of the viewing window when the bike is upright.

Nov 10, 2008 | 2004 Vertemati SR600

1 Answer

Oil filter


To change your oil filter remove oil drain plug drain oil into an oil pan clean and replace oil drain plug, then remove oil filter, pour a drop of clean oil onto a new oil filter, and lube gasket, then replace the old oil filter with the new oil filter. Finally, add clean oil to the motorcycle until the oil level window shows oil in the middle of the viewing window when the bike is upright. ,,,

Nov 10, 2008 | 2001 Sachs Roadster 800

1 Answer

Oil filter


To change your oil filter remove oil drain plug drain oil into an oil pan clean and replace oil drain plug, then remove oil filter, pour a drop of clean oil onto a new oil filter, and lube gasket, then replace the old oil filter with the new oil filter. Finally, add clean oil to the motorcycle until the oil level window shows oil in the middle of the viewing window when the bike is upright. ,,,

Nov 10, 2008 | 2008 Qlink XF 200

1 Answer

Oil filter


To change your oil filter remove oil drain plug drain oil into an oil pan clean and replace oil drain plug, then remove oil filter, pour a drop of clean oil onto a new oil filter, and lube gasket, then replace the old oil filter with the new oil filter. Finally, add clean oil to the motorcycle until the oil level window shows oil in the middle of the viewing window when the bike is upright. ,,,

Nov 10, 2008 | 2005 Qianjiang QJ125T-12C

1 Answer

Oil filter


To change your oil filter remove oil drain plug drain oil into an oil pan clean and replace oil drain plug, then remove oil filter, pour a drop of clean oil onto a new oil filter, and lube gasket, then replace the old oil filter with the new oil filter. Finally, add clean oil to the motorcycle until the oil level window shows oil in the middle of the viewing window when the bike is upright. ,,,

Nov 10, 2008 | 2005 Qianjiang QJ125

1 Answer

Oil filter


To change your oil filter remove oil drain plug drain oil into an oil pan clean and replace oil drain plug, then remove oil filter, pour a drop of clean oil onto a new oil filter, and lube gasket, then replace the old oil filter with the new oil filter. Finally, add clean oil to the motorcycle until the oil level window shows oil in the middle of the viewing window when the bike is upright. ,,,

Nov 10, 2008 | 2004 Petronas FP1

1 Answer

Oil filter


To change your oil filter remove oil drain plug drain oil into an oil pan clean and replace oil drain plug, then remove oil filter, pour a drop of clean oil onto a new oil filter, and lube gasket, then replace the old oil filter with the new oil filter. Finally, add clean oil to the motorcycle until the oil level window shows oil in the middle of the viewing window when the bike is upright. ,,,

Nov 10, 2008 | 2006 Maico 320 Supermoto

1 Answer

Oil filter


To change your oil filter remove oil drain plug drain oil into an oil pan clean and replace oil drain plug, then remove oil filter, pour a drop of clean oil onto a new oil filter, and lube gasket, then replace the old oil filter with the new oil filter. Finally, add clean oil to the motorcycle until the oil level window shows oil in the middle of the viewing window when the bike is upright. ,,,

Nov 10, 2008 | 2004 Kymco Venox 250

Not finding what you are looking for?
2001 Yamaha V Star 1100 Classic Logo

507 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1176 Answers

Paul Ellermets

Level 1 Expert

6 Answers

Neil Lancaster
Neil Lancaster

Level 1 Expert

14 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...