20 Most Recent KitchenAid KEMC378 Electric Double Oven Questions & Answers


switch off electricity to oven, then switch it back on - that reboots the computer that controls the oven.

KitchenAid... | Answered on Jul 09, 2018


your door or interlock switch is not closing press on the door see if it stars if so you will have to check you alignment if not the switch could be bad you wuill need to open the ctrl panel to get to the switches unplug first

KitchenAid... | Answered on Jul 09, 2018


If you've determined the keypad on your Kitchenaid oven, range, or wall microwave is faulty and youre searching for an obsolete part, http://www.FixYourBoard.com has replacements by Ledgestone Technologies. These units are backed with a 2 year warranty. Save your $ and save your oven from the landfill. We have you covered! Call 512-355-1108 for more information and to order. We're happy to help you solve your problem!

ledgestone keypad kp1b1705-vce5mquz3yp03nzfysmmck3z-1-0_0.png
FixYourBoard.com

KitchenAid... | Answered on Sep 12, 2017




F1 - E1
EEPROM checksum error

1.
Disconnect power for at least 30 seconds.
2. Re-apply power and observe for
at least one minute.
3. If code re-appears, replace control board (also
called ERC or clock).

Note: Applies to all F1-E...
codes except F1-E3.

KitchenAid... | Answered on Sep 12, 2017


1. self cleaning cycles destroy parts.
2. replace the thermal fuse behind the rear panel of the oven.

KitchenAid... | Answered on Nov 29, 2016


See if the door is crooked, low, or something is blocking it.

KitchenAid... | Answered on Dec 01, 2013


The F-3 error code typically means you have sensor problem. The sensor is usually mounted in the oven space up near the top of the unit. The first thing to do is turn off the circuit breaker to the oven. Do you have an ohm meter? I suggest if you don't to purchase one. They are relatively inexpensive. Maybe you can borrow one from a friend. Disconnect the sensor from the electronic control and measure the resistance. There should be a wiring diagram in the top of the unit that will help you to locate the sensor wires. Most sensors should read around 1100 ohms at room temperature. If sensor reads as an open circuit or has a very high resistance, it must be replaced. If instead it reads very low, then there is a short in the wiring. Some units have a fuse in series with the sensor. Check to see that the fuse has not blown.

KitchenAid... | Answered on Apr 20, 2013


F2 - E6 Cancel key drive line open 1. Check keypad connector for firm connection (keypad connects to control board).
2. Press CANCEL. If error code returns after 60 seconds, replace keypad (also called touch pad or membrane switch). Some models incorporate keypad in to control board as one unit. In this case, replace control board (also called ERC or clock).

KitchenAid... | Answered on May 05, 2011


the light cover at the back of the oven needs to be unscrewed. There is normally 2 or 3 little screws involved. Once it has been removed it's like any other light bulbs, unscrew and change. Make sure to put back the cover tightly in place or the light will burn when the oven turns on.

KitchenAid... | Answered on Mar 14, 2011


The problem is with the "probe jack" that the probe plugs into. Replace the jack and all will be good. Here is a link to the part.

KitchenAid... | Answered on Feb 27, 2011


F1-E1 - EEPROM Checksum Error - Disconnect power for at least 30 seconds and then reconnect.
Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

KitchenAid... | Answered on Oct 01, 2010


The part CNTRL-ELEC solved our problem. The warranty repair person replaced it and it has worked fine for a week now.

KitchenAid... | Answered on Sep 10, 2010


Hi,
You will have to kill the power to the oven at the circuit breaker or pull the plug...

Self Cleaning Oven Problem

heatman101

KitchenAid... | Answered on Sep 08, 2010


F1- E0 = electronic control malfunction. Replace control see page 21.



If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

KitchenAid... | Answered on Mar 26, 2010

Not finding what you are looking for?
KitchenAid KEMC378 Electric Double Oven Logo

44 questions posted

Ask a Question

Usually answered in minutes!

Top KitchenAid Ovens Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

jdthefixer

Level 3 Expert

746 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a KitchenAid Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

KitchenAid Ovens

  • KitchenAid Ovens

Most Popular Question

error code e6 f2

  • Ovens
Loading...