Top 20 Kenmore 65942 Electric Dryer - Page 10 Questions & Answers


Based on symptom and details, the control has detected a component failure. Since your model does not have digital display window in order to display a fault code, it will flash the four indicator lights of

Drying, Cool Down, Wrinkle Rid (Press Saver), and Clean Lint Filter will flash the number of times for the first digit of the code and the START indicator light will flash the number of times for the second digit.

Take separate counts of each indicator light, then repeat to confirm in order to be accurate in identifying the proper error code. The code is obtained by counting the number of times the lights flash. Example E24: The four indicator lights would flash twice indicating the 2 and the START indicator light will flash four times indicating the 4. The four indicator lights and the START indicator light

start flashing at the same time. The control will pause for 2 seconds, then repeat the code.

The failure is likely because of a faulty thermistor or because the heater is not working. It could have a broken heating element or a burnt wire connection at the control board. I would begin by accessing the thermistor and disconnecting it. The thermistor can be tested with an Ohm meter. The thermistor should measure approximately 50,000/5K Ohms at room temperature.

The heating element is located behind the drum and it can be disconnected and tested for continuity with an Ohm meter.

NOTE: Disconnect the dryer from the power supply before servicing.

Kenmore Dryers | 156 views | 0 helpful votes


searspartsdirect.com will identify part numbers when you contact them and identify model 110.67032601.

Kenmore Dryers | 616 views | 0 helpful votes


yes,unplug it,get a putty knife and slide it under the top control panel on each corner,there's two clips one on each side,then when you free up the control panel there's 3 1/4 inch screws,remove them and slide the top panel forwards,there's 2 phillips screws that hold the door switch in place,get a thin tip screw driver,slide it into the plastic wire connector to separate the switch from the harness.i'm pretty sure this is how you get the top off.go here,open top and console and you'll see the clips on the top panel,then go to cabinet parts and the door switch is the common one it's number 41 on the look up part WP3406107 hope this helps you out,
https://www.searspartsdirect.com/model-number/11068002010/0582/0151200.html?searchType=modelSearch&q=110.68002010&searchTerm=110.68002010

Kenmore Dryers | 359 views | 0 helpful votes


Sounds like the motor is overheating and shutting off on its internal overload. You will need a new motor.

Kenmore Dryers | 103 views | 0 helpful votes


Defective heating element/system or control

Kenmore Dryers | 192 views | 0 helpful votes


That would be a heater relay failure. You will need a control board.

Kenmore Dryers | 202 views | 0 helpful votes


Clean filter and rest
Read manual about unit cool and energy saver mode.a4xeqizqmrq6aaaaaelftksuqmccaa==

Kenmore Dryers | 146 views | 0 helpful votes


http://www.wellalashes.com/factory-mink-lashes-wholesale/ Factory Mink Lashes Factory Mink Lashes Wholesale Mink Eyelashes Silk Lashes Factory Mink Lashes Wholesale Mink Eyelashes Silk Lashes price is fast shipped from our lashes factory. Our mink lashes with Premium quality, strong curl durability is handmade, natural, soft, comfortable feeling.You can get the luxury customized package box for mink lashes. Big discount and Free sample Available
http://www.wellalashes.com/factory-mink-lashes-wholesale

Kenmore Dryers | 143 views | 0 helpful votes


Go to www.repairclinic.com and enter the model. With luck, you will be presented with a list of common repair parts/assemblies and may be able to view a generic Kenmore video showing disassembly.

Kenmore Dryers | 108 views | 0 helpful votes


I would check Kenmore Dishwasher Thermal Fuse W10402110
RepairClinic Item #2443847 ' Whirlpool OEM Part #W10402110 Price $23.00 This will require removal of unit and some disassembly This may or may not be problem. You might want to weigh the options have it repaired or buy an new unit . If you fix this unit that is no longer made you will have a an old unit. In my experience dishwasher are not worth repair.
Thermal Fuse W10402110

Kenmore Dryers | 259 views | 0 helpful votes


This is the heating element that has failed. They are about 100 dollars to replace unless you call a service tech out to your address. Then it is more. The model number you listed does not show up on any of the major appliance parts warehouses.

Kenmore Dryers | 292 views | 0 helpful votes


if you go to the below site there is a video on the page that will walk you thru replacement and the part if needed. There is a 877# that can help too.

http://www.appliancepartspros.com/parts-for-model-kenmore-41783042300.html
hope this helps.
best to you.

Kenmore Dryers | 428 views | 0 helpful votes


Heating element/system or control failure

Kenmore Dryers | 110 views | 0 helpful votes


due to the age the specs are nowhere to be found. here's a like to figure it out though......
https://www.shopyourway.com/questions/1143729

Kenmore Dryers | 154 views | 0 helpful votes

Not finding what you are looking for?
Kenmore 65942 Electric Dryer Logo

25 questions posted

Ask a Question

Usually answered in minutes!

Top Kenmore Dryers Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Ned Halaweh
Ned Halaweh

Level 2 Expert

240 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Kenmore Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Kenmore Dryers

  • Kenmore Dryers

Most Popular Question

kenmore 70 series electric dryer

  • Dryers
Loading...