Top 20 York Furnace Draft Inducer Blower Fasco # A224 Questions & Answers


  1. sounds like the control board. i cannot confirm this as i am not able to come sit in front of your furnace. please have a tech come to sit in front of your furnace and figure it out!!

York Furnace... | 324 views | 0 helpful votes


sorry but a search for that did not locate anything here in USA

York Furnace... | 346 views | 0 helpful votes


small dual gas turbine and use electric heating and supplies your home also ....

York Furnace... | 56 views | 0 helpful votes


The "mother board" or integrated control module is essentially the brain that controls the sequence of operation in your gas fired furnace. It is located, generally, in the blower compartment. That is the bottom of the two compartments of the in the furnace. It looks like a circuit board with all the wires of the furnace leading to it.

York Furnace... | 130 views | 0 helpful votes


Does it run if youn pull the thermostat from the base?

York Furnace... | 70 views | 0 helpful votes


filter may not be in correctly. if it is gas, check the pilot, if it doesn't have a pilot, it may be the ignitor. depending on how new your furnace is, it may have a safety feature that won't let it start for some reason. seeing that it will at least start the cycle is a good sign. it may be the filter not placed right. i'm not a furnace expert, just know my experiences. you may want to look at the limit switches as well, they only require a tester to see if they are good. if you own the testers, you probably know what you're looking for.

York Furnace... | 123 views | 0 helpful votes


If the light flashes red 7 times, the furnace is not sensing flame. Check for a flame sensing rod (small steel rod in the path of the main burner flame). If you can see it, shut off the furnace, and clean the rod with a rag soaked in vinegar. Turn the furnace back on and see if this cures yyour fault. Make sure you turn the power off to the furnace and then back on as this will reset the circuit board.

York Furnace... | 1,245 views | 0 helpful votes


There is a switch, activated when you open the service panel, that kills most power to the unit, including the DI Blower motor. Your furnace should also be equipped with an exterior kill switch, or there's always the good old breaker box. Good Luck!

York Furnace... | 82 views | 0 helpful votes


Is your filter plugged? If so, change it out. is the bottom door on the furnace? Is the draft motor running at normal speed?

York Furnace... | 102 views | 0 helpful votes


OK so you replaced the Thermostat huh? OK well then did you also replace the Thermistor Temperature Sensor? or whatever is used? As often it's BOTH, also check the wiring from the sensor to the host, in any event if it's NOT that then all it can be is the controller board, most likely the Micro? Check any and all sensors first though.. try to get a service manual too, it's hard without one?

York Furnace... | 554 views | 0 helpful votes


There should be a gasket between the mounting flange of the inducer motor and the furnace. If you do not have that you can use a small bead of blue or red silicone caulking to seal it. Hope this helps you. Thanks

York Furnace... | 798 views | 2 helpful votes


These pressure switches are safety features on ALL new furnaces, if replacing the switch didn't solve the problem, you might want to make sure there is no blockage in the exhuast pipe like a birds nest, anything that would restrict airflow, is there inline fan motor in the exhaust pipe ? perhaps it's not working also.

York Furnace... | 802 views | 2 helpful votes


I normally would not say this after running my own plbg. htg and a.c. shop for 25 years I always tried to give the competitors the benifit of the doubt. However in this instance I think you need to find a different company cause it sounds like they are ripping you off.Theses motors and squuirrel cage blower usually run about 75-80 dollars and maybe two to three hours on the long side to install.If you are mechanically inclined you can do it yourself. Sorry I'm no more help. Good luck and thank you.

York Furnace... | 443 views | 1 helpful votes


York Diamond blinking nine times

York Furnace... | 901 views | 0 helpful votes


replace the fuel nozzel.....if its plugged or restricted it will do this....change fuel filters as well

York Furnace... | 312 views | 0 helpful votes


I had blades break off on my inducer blower. It was a fairly simple fix. Ordered the part online.

York Furnace... | 688 views | 0 helpful votes


It sounds as if the furnace is working properly. The thermostat is not calibrated.
It is cold here and my heat runs a lot. If you can live with the numbers being off then don't worry about it.

York Furnace... | 121 views | 0 helpful votes


Hi,
I am assuming that the blower in question is the indoor blower motor and no the inducer fan...

The problem is usually caused by a bad circuit board relay and actually is a very common problem...

To be sure... you can jumper the 110 current directly to the motor and see if it will run...

If it does then ...

Replace the circuit board and you'lll be working again....

heatman101

York Furnace... | 849 views | 1 helpful votes


If you're refering to the flammable vapor sensor, it would be part of the gas valve assembly. See what type of gas valve you have. Look it up on the internet. There are several different methods to reset the flammable vapor sensors. White -Rodgers makes one that has two different methods depending on model.

York Furnace... | 588 views | 0 helpful votes

Not finding what you are looking for?
York  Furnace Draft Inducer Blower Fasco # A224 Logo

136 questions posted

Ask a Question

Usually answered in minutes!

Top York Tools & Hardware - Others Experts

Brad Brown

Level 3 Expert

18139 Answers

Bob Janelli

Level 1 Expert

26 Answers

djbilo

Level 2 Expert

84 Answers

Are you a York Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

York Tools & Hardware - Others

  • York Tools & Hardware - Others

Most Popular Question

removed fasco 7021 11577s when bearings

  • Tools & Hardware - Others
Loading...