York Furnace Draft Inducer Blower Fasco # A224 - Answered Questions & Fixed issues


  1. sounds like the control board. i cannot confirm this as i am not able to come sit in front of your furnace. please have a tech come to sit in front of your furnace and figure it out!!

York Furnace... | Answered on Jan 03, 2018 | 316 views


sorry but a search for that did not locate anything here in USA

York Furnace... | Answered on Nov 18, 2017 | 346 views


Hi check out the pressure switch clean the air filter and check out the fan control see if this is clean

York Furnace... | Answered on Nov 06, 2015 | 967 views


small dual gas turbine and use electric heating and supplies your home also ....

York Furnace... | Answered on Aug 14, 2015 | 56 views


Does it run if youn pull the thermostat from the base?

York Furnace... | Answered on Jun 08, 2014 | 70 views


The "mother board" or integrated control module is essentially the brain that controls the sequence of operation in your gas fired furnace. It is located, generally, in the blower compartment. That is the bottom of the two compartments of the in the furnace. It looks like a circuit board with all the wires of the furnace leading to it.

York Furnace... | Answered on Dec 19, 2014 | 130 views


filter may not be in correctly. if it is gas, check the pilot, if it doesn't have a pilot, it may be the ignitor. depending on how new your furnace is, it may have a safety feature that won't let it start for some reason. seeing that it will at least start the cycle is a good sign. it may be the filter not placed right. i'm not a furnace expert, just know my experiences. you may want to look at the limit switches as well, they only require a tester to see if they are good. if you own the testers, you probably know what you're looking for.

York Furnace... | Answered on Dec 03, 2013 | 120 views


Hello,
Check the pressure switch and the little hoses going to the pressure switch. If the pressure switch does not get a vacum from the blower it will not let the furnace light.

Heatman101

York Furnace... | Answered on Sep 15, 2013 | 1,141 views


how can I fix the spill limit switch, also how do I found it

York Furnace... | Answered on Mar 23, 2013 | 2,988 views


There is a switch, activated when you open the service panel, that kills most power to the unit, including the DI Blower motor. Your furnace should also be equipped with an exterior kill switch, or there's always the good old breaker box. Good Luck!

York Furnace... | Answered on Mar 10, 2015 | 82 views


If the light flashes red 7 times, the furnace is not sensing flame. Check for a flame sensing rod (small steel rod in the path of the main burner flame). If you can see it, shut off the furnace, and clean the rod with a rag soaked in vinegar. Turn the furnace back on and see if this cures yyour fault. Make sure you turn the power off to the furnace and then back on as this will reset the circuit board.

York Furnace... | Answered on Jan 05, 2013 | 1,199 views


Is your filter plugged? If so, change it out. is the bottom door on the furnace? Is the draft motor running at normal speed?

York Furnace... | Answered on Jan 05, 2013 | 102 views


Have your gas supplier verify delivery pressure. Too high or low, the valve will lock up. Should be a free service.

York Furnace... | Answered on Nov 08, 2012 | 697 views


The furnace is not sensing the flame. Turn off the power.
There is a metal rod in front of the last burner to light. It is corroded and needs to be cleaned. Its the flame sensor .
take the 1 screw out holding it in to the bar and scrub it with some steel wool till shiny. replace and turn on furnace. all should be fine.

York Furnace... | Answered on Dec 22, 2011 | 1,647 views


OK so you replaced the Thermostat huh? OK well then did you also replace the Thermistor Temperature Sensor? or whatever is used? As often it's BOTH, also check the wiring from the sensor to the host, in any event if it's NOT that then all it can be is the controller board, most likely the Micro? Check any and all sensors first though.. try to get a service manual too, it's hard without one?

York Furnace... | Answered on Nov 15, 2011 | 549 views


York Diamond blinking nine times

York Furnace... | Answered on Jul 29, 2011 | 897 views


There should be a gasket between the mounting flange of the inducer motor and the furnace. If you do not have that you can use a small bead of blue or red silicone caulking to seal it. Hope this helps you. Thanks

York Furnace... | Answered on Dec 21, 2013 | 798 views


replace the fuel nozzel.....if its plugged or restricted it will do this....change fuel filters as well

York Furnace... | Answered on Feb 26, 2011 | 312 views

Not finding what you are looking for?
York  Furnace Draft Inducer Blower Fasco # A224 Logo

136 questions posted

Ask a Question

Usually answered in minutes!

Top York Tools & Hardware - Others Experts

Brad Brown

Level 3 Expert

18127 Answers

Bob Janelli

Level 1 Expert

26 Answers

djbilo

Level 2 Expert

81 Answers

Are you a York Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...