Briggs & Stratton Briggs Stratton Vanguard V - Twin Vertical Ohv Engine with Electric Start 23 Hp, 1" X 3 5/32" Shaft, ModelNo. 386777 - 0036 - E1 - Page 8 - Answered Questions & Fixed issues


need more information. Glow plugs? Is it cranking? Injector pump primed? There are a lot of different reasons.

Briggs &... | Answered on Oct 18, 2013 | 54 views


Go for a hotter plug but the burning oil means that the rings are worn and need to be replaced.

Briggs &... | Answered on Jun 08, 2013 | 72 views


Sounds like your carb is plugged up with gunk. Will require a good cleaning OFF the engine. This includes running small diameter wire into the ports and bore holes in the carb to dislodge any gunk in them. You can use low pressure air to blow out the channels and hoes, even your breath will be enough, just blow through a straw or tube, or use WD40 with the red tube that comes with it to flush the channels. Make sure you keep track of all parts you remove!! Work on a tray or other containment surface.

Make it nice and clean and then reassemble and reinstal on engine.

Also make sure your air filter is clean.

Briggs &... | Answered on Oct 08, 2012 | 176 views


starter is very ??? Can you turn motor by hand? (mower blade turns)

Briggs &... | Answered on Aug 24, 2012 | 105 views


change filter

Briggs &... | Answered on Jul 11, 2012 | 38 views


Yes, your gut may be right on the fuel mixture. It may also be the piston rings are worn and need replaced. But you should definitely try the right fuel mixture first! Another way to back up the gut is to take the muffler off and look into the cylinder that way. If there is a lot of carbon build up in there, then you know that that is the problem. There will also be carbon build up in the muffler too.

Good Luck!

Jim

Briggs &... | Answered on Aug 08, 2011 | 178 views


Although you may not have the exact mower that is in the video, all of your smaller mowers are pretty much the same.



Good Luck with your project!

If you should have any questions about"Drywall Finishing/Patching", or know someone who does, put your questions to Category:"Tools- Building & Power- HAND TOOLS" at FixYa.com

I will do my best to answer your questions about drywall finishing. However, it would be best if we could speak on the PHONE or do a live CHAT. I can answer any question you have if it involves getting a wall ready for paint!

Thanks for looking,

Jim

Briggs &... | Answered on Aug 08, 2011 | 92 views


I had a B&S lawn mower engine that did this unless I kept pushing on the prime button and I found I had a Cracked primer rubber bulb. Maybe you have something similar or another type or carb problem.

Briggs &... | Answered on Jul 28, 2011 | 178 views


David,

Has anyone checked the valve clearance on the engine?

Also, sometimes simple things will make the engine perform intermittently. Try running it without the gas cap on when it has died. It could be a clogged gas cap so the engine is not ventilating.

Handie Andie

Briggs &... | Answered on May 27, 2011 | 52 views


Most modern push mowers have a safety bar near or on the push handle. The cable may be stretched need a slight adjustment.

Briggs &... | Answered on Jan 27, 2011 | 151 views


If this engine has been sitting for awhile I would guess the carb. is gummed up and need a good cleaning. First thing I would do is try a fresh spark plug. Just because the plug looks good doesn't mean it is. If you have a fuel filter check this also. If it is getting fuel into the carb and has spark and compression I would remove the carb and clean it.

Hope this helps

Bob

Briggs &... | Answered on Oct 28, 2009 | 302 views


I would start by draining the old gas out of the tank and filling with fresh gas. Replace the spark plug.

Briggs &... | Answered on Jul 13, 2009 | 246 views


For PaperPro Prodigy. Best stapler I have used but after about 8 years the flat steel staple driver broke. To repair, remove the bottom by forcing it back, force the stapler halves apart with a flat screw driver and the top comes off. The springs and levers are on one half and they will not fly apart. I couldn't find the staple driver part (on the left) so go to the store and buy a new stapler.
img_20200110_114233-undefined-undefined-0.jpg

Tools & Hardware... | Answered on Jan 10, 2020 | 12,765 views


Type in google staple gun breakdown

Tools & Hardware... | Answered on Jan 08, 2020 | 26 views


Request an assembly diagram from the manufacturer/distributor.

Tools & Hardware... | Answered on Dec 24, 2019 | 1,055 views


Gi?m gi? cung c?p l?m ??p
12799086-undefined-undefined-0.jpg

Tools & Hardware... | Answered on Dec 06, 2019 | 317 views


Scaffolding systems require the use of many accessories. Base jacks, U-head jacks, fork heads and adjustable fork head jacks, v-pressings, c-cups and make up some of the necessary accessories of a scaffolding.

Tools & Hardware... | Answered on Nov 29, 2019 | 39 views


Didnt give much info to go on lol. Make /model and a little more detail on your issue will be needed before anyone can try to help you

Tools & Hardware... | Answered on Nov 13, 2019 | 34 views


In all ro systems filtering sea-water or brackish water, there should be much more waste water than potable water produced. You didn't say if the system is producing potable water. If you can give more information about your inlet water and the quality of your potable water quality I may be able to help.

Tools & Hardware... | Answered on Nov 13, 2019 | 90 views

Not finding what you are looking for?
Briggs & Stratton Briggs Stratton Vanguard V - Twin Vertical Ohv Engine with Electric Start 23 Hp, 1" X 3 5/32" Shaft, ModelNo. 386777 - 0036 - E1 Logo

270 questions posted

Ask a Question

Usually answered in minutes!

Top Briggs & Stratton Tools & Hardware - Others Experts

Bill Boyd

Level 3 Expert

53757 Answers

Randy Schumann
Randy Schumann

Level 2 Expert

408 Answers

Tom Chichester

Level 3 Expert

55370 Answers

Are you a Briggs & Stratton Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...