Briggs & Stratton Briggs Stratton Vanguard V - Twin Vertical Ohv Engine with Electric Start 23 Hp, 1" X 3 5/32" Shaft, ModelNo. 386777 - 0036 - E1 - Page 9 - Answered Questions & Fixed issues


Leaky seal most likely, or a broken spring, or worst a bad valve. Check the seal first, then the spring, then the valve. Always check the cheapest thing first.

Tools & Hardware... | Answered on Nov 02, 2019 | 42 views


Hello Gayle,

I found this video and I hope it helps you out.
https://www.youtube.com/watch?v=wWOubLQ5luc

Good luck,
Andrew

Tools & Hardware... | Answered on Oct 31, 2019 | 43 views


Have to pull off the front face and panels access from the front of machine

Tools & Hardware... | Answered on Oct 25, 2019 | 46 views


Do you mean tremclad? You can either leave it alone and hope it eventually dries, or you can remove it and try again with the right kind of paint. tremclad was made for metal and rust, not cupboards. I suggest you wipe it off with a suitable solvent, perhaps acetone will work. Once you have as much off as possible, sand down the cupboards and paint with latex or even oil base house paint, or if you sand all the paint off you could use a stain. At any rate, use the right product for the job.

Tools & Hardware... | Answered on Oct 23, 2019 | 57 views


Not familiar with your torch, but does it have a trigger? Possibly goes behind the trigger?

Tools & Hardware... | Answered on Oct 11, 2019 | 57 views


LOADING NAILS
* Disconnect the tool from the power source when loading brad nails * Tilt the tool or lay the tool flat, so the nails will not drop out while loading
*Press lever (A) while pulling slider (B) backwards Place the nail strip into magazine (C) (maximum capacity 100 nails)

Tools & Hardware... | Answered on Oct 03, 2019 | 64 views


You have reboot the mobile or new software install

Tools & Hardware... | Answered on Jan 07, 2020 | 1,032 views


fixya sells no parts for anything contact mastercraft for help

Tools & Hardware... | Answered on Sep 27, 2019 | 92 views


Google (amt)(4750)(manual) without parens OR contact AMT directly to request it.

Tools & Hardware... | Answered on Sep 22, 2019 | 78 views


check the power, check the switch, check the bulb. One of those three items is at fault.

Tools & Hardware... | Answered on Sep 20, 2019 | 62 views


You will get all the information on Toolbox & Hardware from here https://toolboxwidget.com. Download your PDF copy today or email us to toolboxwidget@gmail.com for ordering book.

Tools & Hardware... | Answered on Sep 20, 2019 | 101 views


by first engaging the quill lock (or blocking the quill in place), then removing the nut over the center of the spring housing opposite the quill handle, but be very careful; The spring is under a lot of tension, and if broken or jarred, it can fly out of the housing, causing serious injury. I'd strongly suggest you find a service manual for it before attempting any repairs or adjustment. The fact that the quill is binding leads me to believe that the spring is set improperly, which might be remedied by carefully (slightly) loosening the nut, thus allowing you to rotate the housing, allowing a small amount of tension at a time to be removed from the spring, until desired operation is achieved. In any case, no attempt should be made to remove the housing until the spring tension is safely relieved. The procedure is very similar to that for a bridgeport mill, so that manual for quill (clock) spring adjustment/replacement might be of use to you also.

Tools & Hardware... | Answered on Sep 19, 2019 | 198 views


Shapewear is essentially the corset of today. Shapewear slightly shapes the body, smoothes curves and enhance appearance. It also creates support for the wearer. It has a high lycra content. When lycra yarn is stretch, the elasticity causes it to hug the body. It's used to smooth underwear lines and curves. It can also be cut and sew with a woven fabric, thus holding the body in due to the inability for the fabric to stretch (like a corset). To answer your question about if it works, yes it does. With consistent use, you will definitely see a difference as I have. Try to search some relevant on https://www.prettygirlcurves.com/ there are many cool variants.

Tools & Hardware... | Answered on Sep 13, 2019 | 380 views


the pin that makes contact with and drives the nail is coupled to a piston.either that connect has failed OR the piston is stuck in a bind(probably a faulty o-ring)

Tools & Hardware... | Answered on Sep 13, 2019 | 94 views


Google (calhawk)(1000m/m)(manual) without parens.

Tools & Hardware... | Answered on Jul 25, 2019 | 101 views


This belt should be mounted so that the overlap trails when the belt sander is used, sometimes these belts will have arrows indicating the direction of rotation but not always. The arrows usually disappear after a bit of use anyway so if you change grits or re-use belts it is good to know which way to run the belt by looking at the join.

Here another fix that has worked for me. Take some ordinary electricians tape and make several laps around the idler pulley on the belt sander. Put more thicknesses near the center of the idler, than the outside. This effectively builds a small crown on the pulley and makes the belt stay centered. Also, always relieve the tension on the belt when not using the sander. The belt can stretch and tracks poorly if this happens.

Tools & Hardware... | Answered on Jul 17, 2019 | 93 views

Not finding what you are looking for?
Briggs & Stratton Briggs Stratton Vanguard V - Twin Vertical Ohv Engine with Electric Start 23 Hp, 1" X 3 5/32" Shaft, ModelNo. 386777 - 0036 - E1 Logo

270 questions posted

Ask a Question

Usually answered in minutes!

Top Briggs & Stratton Tools & Hardware - Others Experts

Bill Boyd

Level 3 Expert

53768 Answers

Randy Schumann
Randy Schumann

Level 2 Expert

408 Answers

Tom Chichester

Level 3 Expert

55370 Answers

Are you a Briggs & Stratton Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...