20 Most Recent Uniden DCT648-3 Cordless Phone Questions & Answers


I means the paygo phone you are calling is out of funds.

Uniden DCT648-3... | Answered on Dec 27, 2014


You have unheard messages on the voicemail system provided by your telephone company. This system records messages when someone calls while you're already on the phone. Please contact your telephone company for instructions on accessing their voicemail system.

Uniden DCT648-3... | Answered on Jul 09, 2014


On the Base Station select HS Registration then on the Handset hold # for 2 sec

Uniden DCT648-3... | Answered on Oct 16, 2013


This may be a little late, you are probably home already, but here it is anyhow:

Remote Operation
You can check, play, or delete messages, even record a new greeting message from a remote
location (when you are away from home, or from another room using a handset).
Additionally, you can turn On or Off your answering system remotely.
Remote access away from home
You can operate your answering system from a remote location using any
touch-tone telephone.
1) Call your telephone number and wait for the system to answer. If the answering system is
off, it will answer after about 10 rings and sounds a series of beeps.
2) During the greeting message (or a series of beeps when the answering system is off),
press 0 and enter your PIN code within 2 seconds (see "Setting a PIN Code" on page 25
or 54).
3) The answering system announces the current time and the number of messages stored in
memory. You hear "To play incoming messages, press zero-two. For help, press one-zero".
You will hear a beep.
4) Enter a command within 15 seconds, each command there after must be entered within 2
seconds. You may select a command from the following chart:
Command Function Command Function

0 then 1 Repeat a Message* 0 then 6 Answering System On
0 then 2 Playing incoming Messages 0 then 7 Memo Record/Stop**
0 then 3 Skipping a Message 0 then 8 Greeting Message Record/Stop**
0 then 4 Deleting a Message 0 then 9 Answer System Off
0 then 5 Stop Operation 1 then 0 Help Guidance
* For Repeat a Message function, press 0 then 1 within about four seconds to repeat
the previous message, or press 0 then 1 after about four seconds to repeat the
current message.
** For Memo Record and Greeting Message Record function, the first time you enter the
corresponding command, it starts the Recording function. If you want to stop the
recording, press 0 then 7 or 8.

5) After the command has finished, you hear intermittent beeps indicating that the system
is in the command waiting mode. You may enter another command at this time from the
chart above.
6) When you are finished, hang up to exit the system. The answering system automatically
returns to standby.

Uniden DCT648-3... | Answered on Jul 25, 2013


i lock my samsung galaxy pocket
how can i unlucking

Uniden DCT648-3... | Answered on Jan 25, 2013


Here you go
http://www.uniden.com/pdf/DCT648om.pdf
Enjoy!

Uniden DCT648-3... | Answered on Mar 03, 2011


I had this exact problem. My solution was to clean the top of the condensor microphone. Something was spilled onto the phone and ran down into the hole that leads to the microphone. It not only affected the microphone, but made some of the buttons stick as well. The phone is not difficult to disassemble, just try not to touch the electronic components. If you are experienced in electronics, you may know that using a wrist strap( available at electronics supply stores or online) and grounding yourself will help protect the electronics. While you are at it, get some pure isoproply alcohol, and some cotton swabs, making sure that the swab is saturated with the alcohol. Just clean around the interior area of the phone where the condensor microphone is. You will want to even remove the black screen over the microphone to be sure everything is clean!!! Make sure the little hole that leads from the front of the phone to the microphone is clear and clean. I believe you will solve your problem.

Uniden DCT648-3... | Answered on Jan 02, 2010


base station has a display E 1 and no dial tone

Uniden DCT648-3... | Answered on Oct 09, 2009


THAT IS AN ERROR MESSAGE, PHONES NEED TO BE REPLACED.

Uniden DCT648-3... | Answered on Sep 07, 2009


See if in the menu choices there is an option to reset all factory defauts. It seems someone has mistakenly locked out the other to units. Can you still use them as intercoms?

Uniden DCT648-3... | Answered on Aug 13, 2009


I had this exact same problem. I had to reset all three handsets. Select menu, system reset, replacing base, then follow directions. This worked for one unit but the other ones I had to buy new batteries eventhough they showed fully charged. Good Luck

Uniden DCT648-3... | Answered on Jul 01, 2009

Not finding what you are looking for?
Uniden DCT648-3 Cordless Phone Logo

51 questions posted

Ask a Question

Usually answered in minutes!

Top Uniden Lands Phones Experts

k24674

Level 3 Expert

8081 Answers

Cindy Wells

Level 3 Expert

6063 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

Are you an Uniden Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Uniden Lands Phones

  • Uniden Lands Phones

Most Popular Question

handset not working

  • Lands Phones
Loading...