20 Most Recent GE Profile JK915 Electric Single Oven Questions & Answers


It's your oven temperature sensor. It's a thin metal stick that juts into the oven. It is located on the upper right back wall of the oven cavity. Flip your breaker, slide out the oven. You install it from the back, very simple, two screws, i think. I'm a beginner at DIY and had no problem fixing it.

GE Profile JK915... | Answered on Nov 26, 2014


Hi, Consumer. We're sorry to hear about the difficulty with your oven. Below are links to our Use & Care guides, Parts Diagrams, Troubleshooting information and the Service are of our website. We hope this helps! http://bit.ly/112Lu7q

GE Profile JK915... | Answered on Jun 06, 2014


Has this just happened or have you suddenly just tested the oven temperature with a RELIABLE thermometer? Some cheaper thermometers can give a false reading. Check with a accurate thermometer first and place it at intervals in different parts of the oven ( it does vary) and take the average

GE Profile JK915... | Answered on Jan 19, 2014


oven display element supply all working perfectly
only 1 problem i face oven did not heat up...
plz help me quickly
thank you
Regarded
Hannan Ashraf

GE Profile JK915... | Answered on Jan 01, 2013


Appu, the F0 error for this built in means there is a shorted or stuck off key. Sometimes this can be resolved by removing the keypad ribbon cable from the board and cleaning the ends with an eraser. If that doesn't work, you want to find out whether its the board or keypad by ohming the ribbon cable, 3 to 4, probes on the conductor side...should read 125 to 1750 ohms while pressing the off key. Catriver..post back.

GE Profile JK915... | Answered on Oct 07, 2012


  • 1.Press the "Clear/Off" button on the control panel to reset the oven. This will clear the lock setting and unlock the door.

    2.Allow the oven to cool to room temperature to avoid turning the lock on again during this heating cycle.

    3.Reset the oven to the temperature you require to finish cooking by pressing the correct temperature control on the control pad.

    or

  • 1.If your GE Profile microwave won't turn on, unplug it, then plug it back in. A power outage may have occurred due to a power surge. Check your home's fuses and circuit breakers.

    2.Set the clock of your GE Profile microwave. Certain models will not operate until you set the clock. Select the "Clock" key and type in the correct time.

  • 3.Hold down your microwave's "Off" button. You may have accidentally hit the control-lock feature on your GE Profile microwave. Hold down the "Off" button for three seconds to turn the lock off.

  • 4.If the sensors of your GE Profile microwave are not working correctly, remove the food from the machine. If the sensors detect food-surface temperatures over 200 degrees Fahrenheit, it will not work properly until the area cools down.

  • 5.Contact GE Support if you are unable to resolve the issue on your own. Call the GE Support hotline or browse the help library on the GE website. You can also schedule a service visit on GE's website.

  • GE Profile JK915... | Answered on Nov 22, 2011


    If actual over temperature condition occurred: Look for welded relay contacts on bake or broil relays. If this happens, replace oven control (also called clock or ERC).

    If no over temperature condition occurred: Look for a high resistance connection or any other cause of high resistance in the oven temperature sensor circuit. Check sensor, sensor harness and sensor harness connection at sensor and oven control. Replace sensor if found defective.

    Remember: Oven control (ERC) measures resistance of sensor circuit , not actual oven temperature.

    thats what a F2 code is on a GE

    GE Profile JK915... | Answered on Jul 15, 2011


    It sounds like somethin did burn, likely a wire, and it has "gone to ground" and tripped the breaker. If the breaker will only reset momentarily, it is doing it's job, and it is telling you that a hazard exists. It is probably time to call a serviceman, or someone who is comfortable with appliance repair. Good luck, Rob

    GE Profile JK915... | Answered on Jan 01, 2011


    First you need to remove all four burners' bases, so the cook top assembly which is one unit to be clean and by removing the secure screws you can lift up the whole unit. If there is some dry burned oil around it can be stuck but you can use a straight screwdriver as a lever to force it up.

    Now you have clear underneath burner manifold pipe with orifice and air valve control so you can clean and adjust.

    However my advice is to use a thin pin or a metal wire to clean the burner orifice first since if it is dirty the gas pressure is lower and you have the same blackening problems. If after that you still have the same problem then you can adjust the air valve.

    Here below we have a link with the parts layout of your range so it will help you dismantle the cook top assembly and know before how is your range.


    http://www.appliancepartspros.com/partsearch/model.aspx?model_id=5203190&diagram_id=22289624#d22289624

    GE Profile JK915... | Answered on Sep 30, 2010


    Hello there:
    Normally this is due to a bad temperature sensor F3 Open oven temperature sensor circuit Measure oven temperature sensor circuit at oven temperature sensor (should be approx 1100 ohms at room temp); check for cut or pinched wire or loss of contact and replace if found faulty

    GE Profile JK915... | Answered on Apr 30, 2010


    F7 stuck keypad
    Stuck keypad may mean relay is turned on.
    Determine if problem is with the Key Panel or Control by:
    1. Pushing CLEAR/OFF pad.
    2. Disconnecting Ribbon Cable from control and waiting at least 32 seconds to see if Code recurs

    If code recurs, problem is in the control. Replace control.

    If code does not recur, problem is with the Key Panel.

    GE Profile JK915... | Answered on Sep 21, 2009


    I flipped the breaker so that it would go back to its original settings and that worked

    GE Profile JK915... | Answered on Aug 24, 2009

    Not finding what you are looking for?
    GE Profile JK915 Electric Single Oven Logo

    Popular Tags

    33 questions posted

    Ask a Question

    Usually answered in minutes!

    Top GE Ovens Experts

    William Miller
    William Miller

    Level 3 Expert

    9179 Answers

    Ekse

    Level 3 Expert

    13434 Answers

    Marvin
    Marvin

    Level 3 Expert

    85222 Answers

    Are you a GE Oven Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    View Most Popular

    GE Ovens

    • GE Ovens

    Most Popular Question

    access adjustment air fuel

    • Ovens
    Loading...