20 Most Recent Hampton Bay 24750 Huntington III Ceiling Fan Questions & Answers


Yes you can operate them with two styles of remotes: either the remote wall switch, or a hand held remote. Both require the receiver to be mounted above the top of the fan in the base it is wired to. The receiver has wires on both sides; the one side wires directly to the house wires, and the other goes to the fan and light. They are both sold at Home Depot and Lowes. The ones at Home Depot also include the set made by the fan manufacturer.

Hampton Bay... | Answered on Jul 11, 2019


home depot and lowes carry hampton bay products, go to ceiling fan area and replacement blades and hardware are sold in packs of four and five. cheaper than buying a new fan. hope this helps.)

Hampton Bay... | Answered on Jul 02, 2019


mcdevito75 here, Hopefully your ceiling fan will go where there has been an already light fixture, if so, that light fixture shoud be mounted to the ceiling beam, and your new fan will be mounted the same way. If by chance your new ceiling fan is being mounted where nothing was ever mounted you"ll have to make sure the ceiling fan will mount to a beam, they are every 16 inches apart. This way you:"ll know that vibration from the fan won"t hurt anything.

Hampton Bay... | Answered on Jun 25, 2019


I had a hampton bay fan that absolutely did not have a revers switch on the fan anywhere! MOST fans bought today will reverse. I was not about to give up. I scoured the net for an answer and could not find anything to help. I did however find a comment somewhere that said it could be done internally. After about six months I decided to search again (now). Nothing... so I started playing with the remote and the wall switch and Shazaam! I figured it out on my hampton bay fan. Turn the fan on high... Turn the wall switch off.... wait until the fan is pretty slow in rotation... hold the HI button on the remote.... Turn the switch back on. IT Worked for me! Hope this helps someone. SparqMark

Hampton Bay... | Answered on Apr 17, 2018


I never could find the 5 wire 4 speed replacement. I did however find a solution.
4-speed (five-wire) pull-chain ceiling fan speed switch--Use 3-speed ZE-208S6-A09.
How to use the 3-speed ZE-208S-A09 to replace a 4-speed switch:
old ZE-208S5-1T or ZE-268S5: . . . . . for ZE-208S6-A09 use:
L=Black . . . . . . . . . . . . . . . . . . . . . . . . L=Black
1=Gray . . . . . . . . . . . . . . . . . . . . . . . . 1=Gray
2=Brown . . . . . . . . . . . . . . . . . . . . . . . . (Don't use Brown)
3=Purple . . . . . . . . . . . . . . . . . . . . . . . 2=Purple
4=Green . . . . . . . . . . . . . . . . . . . . . . . . 3=Green
old ZE-208S5-1T or ZE-268S5: . . . . . For ZE-208S6-A09 use:
L=Black . . . . . . . . . . . . . . . . . . . . . . . . L=Black
1=Gray . . . . . . . . . . . . . . . . . . . . . . . . 1=Gray
2=Green . . . . . . . . . . . . . . . . . . . . . . . . (don't use Green)
3=Brown . . . . . . . . . . . . . . . . . . . . . . . . 2=Brown
4=Purple . . . . . . . . . . . . . . . . . . . . . . . 3=Purple

Hampton Bay... | Answered on Sep 30, 2017


mcdevito75 here, Close to the ceiling but still on the fan motor shroud should be another small pull chain switch, this pull chain switch is the fan reverse switch, the switch may also be a toggle switch but I doubt it. Look close to the other pull chain switch for the fan, for the reverse switch.

Hampton Bay... | Answered on Jul 17, 2017


4-speed (five-wire) pull-chain ceiling fan speed switch--Use 3-speed ZE-208S6-A09.
How to use the 3-speed ZE-208S-A09 to replace a 4-speed switch:
old ZE-208S5-1T or ZE-268S5: . . . . . for ZE-208S6-A09 use:
L=Black . . . . . . . . . . . . . . . . . . . . . . . . L=Black
1=Gray . . . . . . . . . . . . . . . . . . . . . . . . 1=Gray
2=Brown . . . . . . . . . . . . . . . . . . . . . . . . (Don't use Brown)
3=Purple . . . . . . . . . . . . . . . . . . . . . . . 2=Purple
4=Green . . . . . . . . . . . . . . . . . . . . . . . . 3=Green
old ZE-208S5-1T or ZE-268S5: . . . . . For ZE-208S6-A09 use:
L=Black . . . . . . . . . . . . . . . . . . . . . . . . L=Black
1=Gray . . . . . . . . . . . . . . . . . . . . . . . . 1=Gray
2=Green . . . . . . . . . . . . . . . . . . . . . . . . (don't use Green)
3=Brown . . . . . . . . . . . . . . . . . . . . . . . . 2=Brown
4=Purple . . . . . . . . . . . . . . . . . . . . . . . 3=Purple

Hampton Bay... | Answered on Jun 24, 2017


It's actually a very easy repair. Those pull chain switches are very generic and can be found at home depot or any hardware store for about $3. As far as changing the switch there are only 2 wires to connect and there is no incorrect combination to reconnect them.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jerry_612d8419f8984578

Hampton Bay... | Answered on Jun 24, 2017


There is a a major ceiling fan manufacturer in Fort Lauderdale FL called King of Fans (website: kingoffans.com) that deals strictly with Hampton Bay ceiling fans & parts. They are the Home Depot distributor for Hampton Bay ceiling fans. Their number is 1-800-330-3267. There is also a 1-877-527-0313 number for Hampton Bay products other than ceiling fans...

You can also try ebay for OEM replacement fan remotes for various brands including Hampton Bay...

Hampton Bay... | Answered on Sep 21, 2016


There is a a major ceiling fan manufacturer in Fort Lauderdale FL called King of Fans (website: kingoffans.com) that deals strictly with Hampton Bay ceiling fans & parts. They are the Home Depot distributor for Hampton Bay ceiling fans. Their number is 1-800-330-3267. There is also a 1-877-527-0313 number for Hampton Bay products other than ceiling fans...

Hampton Bay... | Answered on May 06, 2016


In theory, they should. Try Hampton Bay first, and if not, check for aftermarket replacements. Those remotes are simple enough that there is no reason that they can't.

Hampton Bay... | Answered on May 06, 2016


Contact "King of Fans" (kingoffans.com) in Ft. Lauderdale at 800-330-3267. They made or make Hampton Bay fans. I just ordered an arm for mine. Have your UPC number handy.

Hampton Bay... | Answered on May 06, 2016


There is a a major ceiling fan manufacturer in Fort Lauderdale FL called King of Fans (website: kingoffans.com) that deals strictly with Hampton Bay ceiling fans & parts. They are the Home Depot distributor for Hampton Bay ceiling fans. Their number is 1-800-330-3267. There is also a 1-877-527-0313 number for Hampton Bay products other than ceiling fans...

Hampton Bay... | Answered on May 06, 2016


Are you talking about a Hampton Bay ceiling fan product. Is there a label stick attached to the top main housing unit that indicates the model & UPC #. If it;s a Hampton Bay...

There is a a major ceiling fan manufacturer in Fort Lauderdale FL called King of Fans (website: kingoffans.com) that deals strictly with Hampton Bay ceiling fans & parts. They are the Home Depot distributor for Hampton Bay ceiling fans. Their number is 1-800-330-3267. There is also a 1-877-527-0313 number for Hampton Bay products other than ceiling fans...

Hampton Bay... | Answered on Apr 19, 2016


Had this happen to me and it was a hunter fan. Similar problem. Fan worked,lights went out. Took light bulbs out, lowered the light fixture. Tested power coming from the ceiling to the quick connect pins for lights. The power was good. So the Problem's in the light kit. Turns out the government requires all new fans to have certain wattage to lights, set at 190. So 3 60w bulbs or 4 40w. Inside the light kit is a limitor hooked to the black power wire coming from the quick connect,It is smaller wire and mine was pink into limitor and white coming out. Not very big. This went bad so i called Hunter, sending new light kit, but I just wired straight black to black wire bypassed that limitor and lights work fine

Hampton Bay... | Answered on Jan 21, 2015


IIt sounds like there is not power to it, so it could be a loose wire nut on the "hot" side of the circuit inside the fan junction box. That's going to be a pain to get to. If you have power there and the connection is faulty, that's the problem. If you have power there and the connections are good it should operate manually without the remote. If not, I would suspect the fan is DOA.

Hampton Bay... | Answered on Nov 30, 2014


Hi there,
I'm not sure how your set-up is, but I can definitely walk you through it. To simplify it on my end. Let's start with the neutral (white wire) wire first - and to be honest with you, this ISN'T always true out in the field, especially in homes (residential wiring). But, let's assume this has been verified. And before I start, make sure the power is OFF. Now, you want to take this neutral (white) wire to both fixture's only. The neutral (white) wire does NOT go to the switch. After you hook up the neutral wire to the one fan - then connect this to the second fan. They should be connected together (in series with each other). Okay, now that we have the neutral (white) wire connected, and out of the way...you want to connect the other wire on the fixture (most likely black) to the other fixture's wire (black) - and take this down to the switch. So now, you have both fixture's hooked up - with only the black (which will be called the switch leg) going down to the switch. Then, you'll need to find your constant HOT wire (which might also be black) - and take that directly to the switch. So now, the HOT wire brings the electricity down to the switch. When the switch is turned on - then the switch leg (black) wire will send the electricity up to the light/fan. Once the light/fan is in operation - that means the neutral (white) wire - has received the electricity (load), and taken it back to the electrical panel...completing the circuit. THIS, is how it all works. The HOT wire leaves the circuit breaker, and goes directly to the switch. Once the switch is turned on, then it travels up the SWITCH LEG to the fixture. Assuming the switch on the light/fan is ON - which is what you want when working it off of a switch - then, the NEUTRAL wire takes the electricity (load) back to the electrical panel...Completing the circuit! Also, the ground wire's should've been hooked up first - but if there's no grounding available (which happens a lot in homes (residential applications), then don't worry about it. It's a good practice to have all appliances, etc. grounded. You can get a grounding clamp, and ground it to the cold water pipe on your water heater - then run it into the ceiling, and to your light(s). This is for added protection! It will trip the circuit breaker if there's any short in the circuit. I hope I didn't get to complicated here, but feel free to contact me with any further question's. Good Luck, and be patient as you can. You'll see that you can do this...

Hampton Bay... | Answered on Jul 01, 2014


Hi there,
I'm not totally sure what you're asking? Do you need the numbers on the fan because of a bad motor, and need information for it? Or, are you looking for information to operate the remote - which is usually found in the owner's manual - which I'm sure you know already. Or, is your remote not working - and you think there's information on the motor to help assist you? Or, are you not sure why your remote isn't working - and think it's the motor? Well, the remote has a transmitter up inside the canopy - next to the ceiling, where the fan is attached too. This is usually the reason why the remote doesn't work - unless you need new batteries. It's always good to put brand new batteries in a remote, because a lot of times - people take from a drawer, cabinet, another appliance, remote, etc...and this doesn't always solve the issue. Without going into the phenomenom of electrical theory, etc. - I'd just try new batteries, if you haven't done so already. Otherwise, you'll need a new transmitter. Now, the way to see if this is the problem - is to turn off the switch (or better yet, the electricity) that operates the fan - and remove the transmitter. Then, reattach the wires directly. You should have one Hot wire (usually colored, but not always the case) - and one Neutral wire (usually the white wire, but not always the case. After you connected the Hot wire to the colored wire of the fixture, and the neutral wire to the white wire of the fixture. Go back and turn your power source back on again. This should allow you to work the fan with the wall switch. If it comes on, then you know you need a new transmitter. Otherwise, there could be an electrical issue up in the ceiling, or somewhere. However, I don't believe you'll have to go that far. Try the new batteries first, then bypassing the transmitter next - and I believe you should have your answer by then. Good Luck, and I hope this will help you...Jim

Hampton Bay... | Answered on Jun 17, 2014

Not finding what you are looking for?
Hampton Bay 24750 Huntington III Ceiling Fan Logo

225 questions posted

Ask a Question

Usually answered in minutes!

Top Hampton Bay Dryers Experts

Ronald Buckner

Level 1 Expert

21 Answers

Gene Pitts

Level 2 Expert

159 Answers

Marvin
Marvin

Level 3 Expert

85219 Answers

Are you a Hampton Bay Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Hampton Bay Dryers

  • Hampton Bay Dryers

Most Popular Question

hunter cieling fan replacement zing ear

  • Dryers
Loading...